Question about 2011 Toyota Highlander

Open Question

OBDII malfunction code c1427 - 2011 Toyota Highlander

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is OBD code po4 18 on a 2004 Cadillac deville


P0418 Secondary Air Injection System Relay "A" Circuit Malfunction

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

May 22, 2015 | 2004 Cadillac Deville

2 Answers

My car won't start and is showing a p1000 code . What does this mean?


P1000 is a manufacturer specific fault code:

Ford P1000: OBDII Monitor Testing Not Complete.
Jaguar P1000: Engine control module (ECM) - internal error.
Kia P1000: System diagnosis incomplete.
Land Rover P1000: Engine control module (ECM) memory erased - no codes stored.
Mazda P1000: OBDII Drive Cycle Malfunction.

So depending on the manufacturer of your car would depend on the meaning of a P1000 code!

Jan 21, 2015 | Cars & Trucks

1 Answer

What does mil cmd fail mean?


MIL is your malfunction indicator lamp, (check engine light)

CMD is the computer interface port, or OBDII port indicating a malfunction communicating with your cars computer

check all the fuses, primarily any marked pcm and retest your vehicle
note: your check engine or MIL has to be on in KOEO state (key on engine off), if the bulb is burned out everything will still work and the OBDII test computer will show MIL status ON, and if you don't have a computer to tell you that, you must get that light to light in the koeo state.

Aug 25, 2014 | Saturn Ion Cars & Trucks

1 Answer

What causes the engine light to stay on all the time


The check engine light is officially called the Malfunction indicator lamp
or (MIL) it alerts the driver when an OBDII emission or engine management problem occurs.The (MIL) may remain on if the OBDII system has detected a problem and recorded a fault code.
When the OBDII monitors detect a problem , the system sets a pending code . The (MIL) will not come on yet because the system needs to make sure the problem is real and not a temporary glitch . If the same problem occurs on a second trip (under the same conditions) the system will set a diagnostic trouble code (DTC) and turn on the (MIL) .
Hope this helps a bit .
Regards Faldih Higgins

Jun 28, 2014 | 2006 Dodge Grand Caravan

1 Answer

2002 PT Cruiser CRD 2.2 Engine management light is coming on the dash after you drive for about 10 or 15 mins If you leave the car for about 2 hours the engine management lights goes out the codes are...


Take your car to an auto parts store and ask them to put a code reader on your car. They not only tell you what the codes are (see below) but also the most likely cause and most likely solution. Or Go Look up OBDII Codes

I personally would start by buying throttle body cleaner and having them show you where to spray it.

Code 1511: Idle Switch (Electric Control Throttle)Circuit Malfunction

Code 0070: Outside air temperature sensor -circuit malfunction

Code 0015: Engine Coolant Temperature Circuit Malfunction


Code 0010: IAT Circuit Malfunction

Oct 24, 2013 | Chrysler PT Cruiser Cars & Trucks

2 Answers

2000 ford explorer p1504 code on OBDII


P1504 Idle Air Control Circuit Malfunction here are possible causes IAC circuit open
VPWR to IAC solenoid open
IAC circuit short to PWR
IAC circuit short to GND
Damaged IAC valve
Damaged PCM

heres what I would check,
This code means that there is a fault in your IAC valve located near the throttlebody.

Aug 27, 2011 | 2001 Ford Mustang

1 Answer

I have a 2004 Dodge Ram 3500 why do codes p0483,0541,0243,2121,2127 keep coming up what do these codes keep coming up


To get the meanings of these codes go to
http://www.obdii.com/obdii.html
P2121 - Check with dealer on this code
P2127 - Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
P0483 - Cooling Fan Rationality Check Malfunction
P0243 - Turbocharger Wategate Solenoid 1
P0541 - Air Intake Heater Circuit Low
If you are located near a National Auto Parts store (AutoZone, Pep Boys, etc.) I would take the truck in and have them run diagnostics.
Let me know if you have any other questions. Thanks.

Apr 14, 2011 | 2004 Dodge Ram 3500 Truck

1 Answer

Check engine light comes on


A malfunction indicator lamp (MIL), commonly referred to as the "Check Engine Light" is an indicator of malfunction of the computerized engine management system. It is found on the instrument console of most automobiles. When illuminated, it is typically either an amber or red color. On vehicles equipped with OBD-II, the light has two stages: steady (indicating a minor fault such as a loose gas cap or failing oxygen sensor) and flashing (indicating a severe fault, that will eventually destroy the catalytic converter, such as a misfire). When the MIL is lit, the engine control unit stores a fault code related to the malfunction, which can be retrieved with a scan tool and used for further diagnosis. The malfunction indicator lamp is usually labeled with the text check engine, service engine soon, check engine soon, or a picture of an engine.
The MIL appeared in the early 80s along with computerized engine controls. Even the earliest systems, such as GM's CCC (Computer Command Carburetor) system had self diagnosis functionality. When the computer detected a fault, it illuminated the MIL. Up until OBDII, on most cars the MIL could output codes, when two pins on the ALDL are jumped, the light would flash the codes, for instance (blink) (pause) (blink) (blink) for code 12. Some manufacturers retained this feature even after OBDII, such as Honda.

Hope this help (remember comment and rated this). Good luck.

May 09, 2010 | 1995 Toyota Camry

1 Answer

OBDII CODE PO446. WHAT NEEDS TO BE REPLACED


The vapor pressure sensor, VSV for canister closed valve (CCV), VSV for pressure switching valve are used
to detect abnormalities in the evaporative emission control system.
The ECM decides whether there is an abnormality in the evaporative emission control system by the vapor
pressure sensor signal.
DTCs P0441 and P0446 are recorded by the ECM when evaporative emissions leak from the components
when there is a malfunction anywhere in the VSV for EVAP, the VSV
for pressure switching valve, or in the vapor pressure sensor itself.

checked basic , gas cap.

More than likely you need to take to a garage , rec. dealership
will have to perform a smoke check to see if there is a leak somewhere or wether there is a malfunction with a vac. solinoid valve(vsv)

Apr 17, 2010 | 2001 Toyota Camry Solara

Not finding what you are looking for?
2011 Toyota Highlander Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...