Question about Cars & Trucks

Open Question

2001 mitsubishi diamante, no headlight warning?

No warning buzzer when headlights are left on and removing key, opening door. Is there something to adjust or fix? Hard to believe it wasn't a standard function.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
HondaAl
  • 72 Answers

SOURCE: headlights reminder buzzer malfunctions.

First does the dome light come on when the drivers door is opened? If not check the door switch, if it is not working, the circuit is not completed to turn on the buzzer.

Posted on Apr 19, 2009

Ad
Hightower971
  • 183 Answers

SOURCE: Headlight reminder buzzer does not work.

Change the fuse.

Posted on Apr 25, 2009

techbuster
  • 5081 Answers

SOURCE: 2003 MITSUBISHI GALANT HOW TO REPLACE HEADLIGHT BULB

First you disconnect the 3 prong electric plug. To disconnect squeeze the side tabs together (hard) and pull away from the bulb, then you can pull off the protective rubber covering, (its a little snug so give it a tug from the 2 tabs on the top and bottom).

Next unscrew the little Phillips head screw to loosen the bracket that clips in the bulb (take note of how the clip is installed before you remove it, it holds the bulb securely in place).
Just loosen the screw as you do not need to remove it all the way. Pull out the old bulb and replace it with the new one.

The bulb has 3 spacing tabs on it so it can only go in one way. Make note of this when you remove it so you may replace it the same way. follow the steps in reverse and your done.
Note: The little wire clip that holds the bulb in can be a pain. Make sure you get a really good look at it, since it pops out as soon as you loosen the screw. If you get lost, you can always look at the other headlight. Oh, and don't do this in the dark.

Posted on Sep 28, 2009

  • 1986 Answers

SOURCE: adjusting 2001 nissan frontier headlights

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

If you have one adjustment screw, it will control your vertical aim. If you have two adjustment screws, one will control your vertical aim and the other will control your horizontal aim

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 30, 2009

  • 4793 Answers

SOURCE: 2001 VW Jetta Headlight adjustment. Headlights

sometimes the headlights stick to the adjusters,just pull/push(wiggle it)to free it, then try setting beams.

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlight warning buzzer not working


My 2010 tacoma doesn't have a buzzer. The lights automatically go off when you turn off the engine and open a door.

Apr 05, 2014 | 2008 Toyota Tacoma

1 Answer

How do you replace headlamps on a 2003 Mitsibushi diamante?


To change a bulb you have to remove the headlight unit ,sorry

Nov 30, 2013 | 2002 Mitsubishi Galant

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

1 Answer

Headlight On alarm sounds every time you open the driver door in a 2002 Intrepid.


put the key in the drivers door and turn to unlock, that should disarm it.

Oct 01, 2012 | 2002 Dodge Intrepid

1 Answer

I am in the Army and away from home attending a course and my wife calls me to inform me that a steady warning chime is going off inside the truck. When I asked to hear the chime it sounds to me like it...


The headlight switch turns on the courtesy light when twisted. Tell her to make sure that the headlight switch is twisted off the indent. If this isn't it, it may be the body control module.

26fe158.gif

Oct 20, 2010 | 2001 Chevrolet Blazer

1 Answer

How do I remove a parklight bulb from the


open the trunk then twist open the lock cover thats in front of the light u want to change then change the bulb.

May 30, 2010 | 2003 Mitsubishi Diamante

2 Answers

How do you stop / turn off an 89 Mustang chime / buzzer?


If You Are Talking About The Door Chime There Are Two Ways To Do It One Is To Simply Unplug the Chime Two Is To Remove The Steering Columm cover and Unplug the black wire that is going to the side of the key switch I would Recommend This Method Because Unpluging The Chime Its Self Will Disable the Headlight on Switch off Warning As Well Removing The wire From Switch on column will disable key in switch door open only

Aug 17, 2009 | 1989 Ford Mustang

1 Answer

Door open w/ key and headlights on alarm not sounding


The two most likely causes of this are either a door catch switch faulty, or the buzzer itself is faulty. If its the door catch switch that is faulty (I am assuming its the drivers door in question), then the control unit will never know that you have opened the door, and therefor the buzzer stays quiet. I would have thought that your car will have a red light that lights up on the dash when you open any door, so check if this operates when opening the door (try it with both doors to see if the light does exist). If this light only works on one of the doors then clearly there is a door catch switch fault. this can be down to the switch itself, located within the door catch or the wiring to it which can sometimes break inside the rubber boot from car to the door near the door hinges. Constant opening and closing the door causes this area to flex back and fourth, and wires sometimes break here.

If the fault is not related to the door, then it is likely to be the buzzer. They do occasionaly fail. Unfortunately they are integral with the dash panael insert (The part with the speedo and rev counter).

Jun 16, 2009 | 2001 Volkswagen Beetle

1 Answer

03 Jetta headlight warning buzzer does not sound.


The sensor is in the door panel itself. The only fix I've found is to dismantle the door to replace the circuit board/sensor contained near the outside door handle. My 02 Jetta hasn't dinges for a few years now.

Jun 05, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

Light warning buzzer constantly on


Have you checked that the headlight switch is in the right position? Are the headlights or parking lights still on when the key is removed?

If so, then rotate the lamp switch to the correct position and the buzzer will go off. Headlights and parking lights are not controlled through the key circuits.

Jan 29, 2009 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...