Question about 1993 Geo Metro

1 Answer

93 geo metro willnot shift

Will not shift out if low from time to time

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Geo Master
  • 20,706 Answers

A/T box. right
the A/T needs service.

Posted on Feb 27, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 1991 geo metro rough idle

i have no idea about an idle up solenoid relay but i had the same problem.. there is a hex screw on the motor that takes a very small allen wrench head where you can adjust the idle from there. its near the throttle body

Posted on Aug 16, 2008

  • 1 Answer

SOURCE: geo metro transmission slips and

Auto Trans I had to replace solenoid in transmission there are two of them when you drop the pan. After testing with a 12 volt battery one was bad replaced and transmission works fine. Mine was a 1996, cost about $90 for solenoid.

Posted on Feb 24, 2009

emissionwiz
  • 76691 Answers

SOURCE: When i start my 1997 Geo Metro, it often sputters

Try this
Here are the most common causes of surges, stalls at stops, low erratic idle speed, rough idle and engine hesitation, it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

Posted on Apr 03, 2009

  • 850 Answers

SOURCE: 1992 Geo Metro w/ automatic. In drive, won't

may be low on fluid as that wont shift the pistons in the valve body of the transmission
due to no fluid pressure!

Posted on Jul 20, 2009

  • 2 Answers

SOURCE: 93 GEO METRO WONT START WHAT DOES DIAGNOSTIC CODE

P0012 = "A" Camshaft Position - Timing Over- Retarded (Bank 1). Check the timing chain/belt. It must be loose. Must be replaced ASAP if it is indeed loose.

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 93 Geo doesn't shift properly


my guess is a bad governor.
bad throttle valve, on rear of tranny, either the cable one, or vacuum one.
the tests are all in the FSM and online at alldata.com, for $15

Jul 15, 2013 | 1993 Geo Metro

1 Answer

Auto trans will shift some times and manual only


It may be just the vehicle speed sensor. Does the speedometer work OK? The vehicle speed sensor tells the computer how to control the shifting and it also sends a signal to the speedometer. Is the trany full of fluid, is it fairly clean? It should be red. Most vehicles, you check the fluid with the engine idling, in park.

Dec 12, 2009 | 1992 Geo Metro

1 Answer

93 GEO METRO WONT START WHAT DOES DIAGNOSTIC CODE 12 MEAN


P0012 = "A" Camshaft Position - Timing Over- Retarded (Bank 1). Check the timing chain/belt. It must be loose. Must be replaced ASAP if it is indeed loose.

Oct 23, 2009 | 1993 Geo Metro

1 Answer

For 93 Geo Metro:blower switch connection


www.autozone.com
When you register for an account (free), the site asks you what car you are driving and then gives you online access to a free manual, including wiring diagrams.

Hope this is helpful,
matt

Sep 18, 2009 | 1993 Geo Metro

1 Answer

1992 Geo Metro w/ automatic. In drive, won't


may be low on fluid as that wont shift the pistons in the valve body of the transmission
due to no fluid pressure!

Jul 20, 2009 | 1991 Geo Metro

1 Answer

How do I set the timing belt on a 93 geo metro without breaking the belt?


Please go to Auto Zone and ask for a Timing Belt Diagram

Jun 13, 2009 | 1993 Geo Metro

1 Answer

93 geo automatic when running won't move much, and is losing heat...


you are low on transmission fluid .

you are low on engine coolant.

check and correct all fluid levels

Jan 25, 2009 | 1993 Geo Metro

2 Answers

93 Geo Metro


As long as they are the same type of engine ( I believe they should both be 1.0L 3 cyl engines). Most parts for the Geo Metro from 1992 to 1994 interchange with out a problem.

Nov 10, 2008 | 1993 Geo Metro

Not finding what you are looking for?
1993 Geo Metro Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...