Question about 2002 Toyota Sequoia

1 Answer

Replacing rear seal

Replace rear wheel seal

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 55 Answers

You will have to take the shaft out. Take the shaft to a machine shop so they can remove the bearing to install the new seal. May also be the internal seal inside the center diff banjo housing. Also check or replace the upper vent to make sure pressure can be released.

Posted on May 04, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wheel seal replace


You will have to remove the rear axle to perform this job The seal will be inside the diff housing and is held in place by the axle bearing.

Nov 08, 2013 | Ford F-150 Cars & Trucks

1 Answer

Rear seal leaking on 2007 ford escape


In order to replace the rear main seal you will need some auto repair tools and experience . this is a big job , the transmission must be removed to replace this seal, also make sure that the seal is the leak,

oil always flows down, a leak on the top of the engine will flow down and drip at the center rear and look like a rear main seal , make sure that is the leak!!.

Depending on what engine you have and if it has 4 wheel drive the time for a shop to do is from 7 to 10 hours depending on engine size and 4wd,

Oct 21, 2012 | 2007 Ford Escape

1 Answer

How hard is it to replace the rear maine oil seal on a 1994 Jeep Grand Cherokee 5.2 liter V8 4 wheel drive


There is some work involve in replacing rear main seal, seal sit in the rear of the engine block, the transmission will have to be remove, and the fly wheel to get to the rear main seal.If you have never removed a engine or transmission, it might be best to pay and have some one do it for you.

Sep 08, 2010 | 1994 Jeep Grand Cherokee

3 Answers

How to replace rear Axle seal on 4x4 chevy


this is very hard if you do not know what you are doing. Ill try to step you through this
  • pull wheels
  • drain pun-kin case
  • pull rear cover
  • in between the spider and axle sets pull C ring with needle nose pliers
  • pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
  • pull seal out at the end of axle housing
  • tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
  • replace axle carefully as the roller bearings are still there
  • replace C clip to original position
  • replace axle diff cover and replace the gasket with a new one
  • refill diff case
  • install tire
  • your good to go

May 03, 2010 | 2002 Chevrolet Silverado

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

I was told I need to replace the seal on the rear


look under the car on the rear diff if it's wet with fluid it should be replaced

Nov 19, 2009 | 2003 Chevrolet TrailBlazer

3 Answers

I have an oil leak between the drivers rear axel and the tire. What parts do I need to look into replacing?


You should be ok replacing the outer seal but check for bearing play or fautly outer wheel bearing before you disassemble. If to much lateral movement in axle shaft it will take out your new seal rather quickley.

Sep 25, 2009 | 2005 Jeep Grand Cherokee

2 Answers

Rear axle seal leaking how difficult would this be to fix


Not that difficult, raise and support the rear of the truck and remove the wheels. Might as well replace both sides so you know you have new seals, remove the differential cover and drain the fluid. Once differential is opened and cleaned , remove the axle "C" clip that hold the axle in place and slide the axle out. Once the axle is out remove the wheel seal and clean around the area. This would be a good time to replace the wheel bearing too since you have access to them and there not that expensive. Install the new bearing and seal, note make sure you oiled the bearing and seal before installing it back and take care when installing the axle back in and "C: clip. Use RTV silicon gasket maker to seal the differential cover and wheels back on and lower. If your lazy like i am, you can drain the differential fluid and replace it with a 50/50 mix with gear oil and Lucas engine oil additives. That may stop the leak and get you a few more miles. You gear oil is 75W-90 and the capacity is 2.6 liters and 3.6 liters if you have the 11.50 Ring gear. Good luck and hope this helps. 

Jul 03, 2009 | 2002 Chevrolet Tahoe

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Replace left rear axle seal 1999 ford explorer


Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the differential housing cover (4033).
    1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
    1. Remove the bolts.
    1. Remove the differential housing cover.
Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
    Remove the differential pinion shaft.
    1. Remove the differential pinion shaft lock bolt.
    1. Remove the differential pinion shaft.
  2. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the U-washer groove.
  3. Remove the U-washer (4N237).
  4. Push the axle shaft inboard.
  5. Remove the U-washer.
Reinstall the differential pinion shaft.
  1. Install the differential pinion shaft.
  2. Install the differential pinion shaft lock bolt finger-tight.
  3. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal (1177).
    Remove the axle shaft.
-----------------------------------------------------------------------------------------------------------------
Seal Removal
  1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.
  1. sxn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
    NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.
6c7eb46.gif Installation
  1. Lubricate the new rear wheel bearing.
    • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
    • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.
  1. Using the special tools, install the rear wheel bearing.

ece7d89.gif
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the wheel bearing oil seal.
c21e27d.gif
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

Feb 22, 2009 | 1999 Isuzu Rodeo

Not finding what you are looking for?
2002 Toyota Sequoia Logo

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...