Question about 2001 Ford Focus

1 Answer

Left door panel

How many screws and how to diiassemble

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

One screw in each corner remove the c clip from the roll up window if manual. remove screws holding the arm rest on and suing a pait scraper pry loose the 8 or so plastic clips in the door and then lift up and out and also remove the lock pole if it has a rounded end, pretty simple.

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove door panel


Trim and molding remove tool and a phillips screw driver
Drivers Side

Remove
Door trim panel and water shield (top where window is)
Plastic panel around door handle. snaps out
1 screw upper front extension assembly (plastic triangle)
2 screws located lower bottom left (drivers side) and door trim panel
Use remove tool to push out retaining 'C' clip behind door handle
Grasp panel where opening are and pull up and out gently
Now disconnect wire harness

May 07, 2013 | 1991 Ford Thunderbird

1 Answer

Thow to take off door pannel and install passenger side window motor on 2000 jeep grand cherokee


first you have to remove dead plugs on door handle and remove screws another screw on door opening handle and you have to disconnect 2 metal pins behind that and look all around the door panel sides and under should have several rivets make sure no any screw and rivets left on door panel pull door panel foward and pull it up dont go too hard dont damage door panel conections for proper reinstallation. before removing door panel from the door dont forget disconnect cable connections from window and door lock switches.good luck

May 07, 2011 | 2000 Jeep Cherokee

1 Answer

I need help pulling the door panel off of my 2006 audi a4


Normally there are four screws to remove. Top left and right of the panel and under the door pull. Remove screws and lift the panel straight up. There is a shield under the door pull . Remove screw and pop out shield. Door panel screws should be visible.

Dec 21, 2010 | 2006 Audi A4

1 Answer

Diagram on how to take off left door panel on 1998 ford expedition


REMOVAL AND INSTALLATION Trim Panel —Front Door, Expedition Removal
  1. NOTE: Release the top portion first.
    Remove the sail panel.
cff7e48.gif
  1. Remove the window regulator switch plate (14524). 3745193.gif

  1. Disconnect the electrical connectors.
d860af8.gif
  1. Remove the upper door trim panel screw. 4b4377b.gif

  1. Remove the door trim panel screw at the window regulator switch plate opening. 149d0a6.gif
  1. Remove the door trim panel screw in the courtesy lamp housing.
    1. Remove the courtesy lamp lens.
    1. Remove the screw. 8fe707b.gif

  1. Remove the inside door handle trim cover. 52f3d0f.gif
  1. Remove the inside door handle.
    • Remove the bolt. abe462f.gif
  1. swj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the front door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the front door trim panel (23943). d6459fb.gif
  1. Remove the courtesy lamp and socket. dfb380f.gif
  1. Disconnect the power mirror electrical connector.
Installation
  1. Connect the power mirror electrical connector.
  1. Install the courtesy lamp and socket.
  1. Install the front door trim panel.
  1. Install the inside door handle.
    • Install the bolt.
  1. Install the inside door handle trim cover.
  1. Install the door trim panel screw in the courtesy lamp housing.
    1. Install the screw.
    1. Install the courtesy lamp lens.
  1. Install the door trim panel screw at the window regulator switch plate opening.
  1. Install the upper door trim panel screw.
  1. Connect the electrical connectors.
  1. NOTE: If a new trim panel is required: Some new trim panels have a cut out opening for the window switchplate that is larger than that on the original trim panel. When installing a new trim panel, install the window switchplate in the following sequence to make sure that the switchplate is secured fully into the door trim panel.
    Install the window regulator switchplate.
    • Insert the rear switchplate clip into the trim panel opening.
    • Install the forward and side clips into the trim panel opening.
  1. NOTE: Install the lower portion first.
    Install the sail panel.

Mar 14, 2010 | 1998 Ford Expedition

2 Answers

Proper way to remove front passenger door panel


some screws.some clips start with screws. one in pull handle also.

Feb 19, 2010 | Mercury Grand Marquis Cars & Trucks

1 Answer

I am trying to pull the door panel on the left driver's side in order to replace the mirror and need guidance as to where to pry or look for holdown screws


The screws are in the armrest, two I think maybe three. There are plastic clips around both ends and the bottom of the door panel. Use a stiff two inch putty knife and slide it in between the door panel and the door. Slide it left or right until you find a clip and pry upward forcing the door panel out to remove the clip from the door. Do this all the way around the three sides. When all clips and screws are out push the door panel upward until it releases from the door frame at the window.

Jan 11, 2010 | 1996 GMC Jimmy

1 Answer

Need to remove left rear door panel


  1. If equipped, remove the window crank handle by using a retaining clip removal tool.
  2. Remove the door handle bezel by inserting a flat trim removal tool between the door panel and handle bezel to release the locking tabs.
  3. Remove all door panel electrical connectors .
  4. Remove the door panel push pins and trim screws. Lift the door panel up and out to release the door panel locking tabs.

May 22, 2009 | 2006 Chevrolet Silverado

1 Answer

How to remove the inside left side front door


Snap out two door pull strap retaining screw covers. Remove screws.
Remove screws on front, rear and center of front door trim panel.
Using the Trim Pad Removing Tool or equivalent, pry the trim panel retaining clips from the door inner panel.
These are plastic so be careful you can use a pair of needle nose pliers if you don't have a trim tool.Just start at bottom of door panel and work your way around and up.

Mar 06, 2009 | 1997 Lincoln Town Car

2 Answers

Removal of left front panel, inside, of 2002 dodge caravan


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls

Feb 18, 2009 | 2002 Dodge Caravan

1 Answer

Door panel


Depends on what door trim you are trying to replace. If you are trying to replace the door trim on the front doors you need to remove two screws from behind the casing around the door handle and then remove a screw from the bottom left of the door and then there will be a screw on the left of the door as high as the arm rest on the door. Finally pull up on the door panel and out to remove the panel. Remove the harnesses and you are complete.

If you are trying to remove the rear doors you need to remove a screw from the bottom of the door again near the left side then remove the screw from behind the casing that surrounds the door handle. Finally pull up on the door panel and out to remove the panel. Remove the harnesses and you are complete.

Oct 27, 2008 | 2001 Ford Crown Victoria

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...