Question about 2007 Pontiac Grand Prix

Open Question

One side of connector is burnt on low beam headlight

The connector on my left low beam headlight was replaced the next day light didn't work and looked at it connector burnt again and headlight wont work

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: headlights

Pull the headlight switch and check for a burned connector, this will cause a poor connection and in turn dim headlights or no lights.

Posted on Oct 27, 2008

  • 83 Answers

SOURCE: 2002 sunfire Drl problem

check wiring in front of washer bottle and harness will lead to passanger side follow it open up harness ussually broken wires inside causing dim or no headlights.

Posted on Jan 03, 2009

  • 1 Answer

SOURCE: low beam headlights not working on 2004 Pontiac Montana extended

You headlight lamp have a diffuser mechanism which allows it to flip between the hight beam and low beam feature of the bulb. In fact, you high beam will function even if the low beam is not working.

I would recommend the purchase of the new headlight lamp. It would cost you you any where from $15.00 per unit to get a replacement lamp

Posted on Jan 06, 2009

  • 11 Answers

SOURCE: Low beam headlights do not

most cars have a fuse or relay for high and low. if they are good test your bulbs then check or replace your dimmer which is in the multifunction switch

Posted on Apr 06, 2009

  • 564 Answers

SOURCE: headlight low beams do not come on

high low switch is gone or both low beams bad

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

2 Answers

What would cause the low beam headlight not to work when all other lights work?


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

May 11, 2015 | 2002 Mercury Grand Marquis

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

Burnt out low beam headlight connector? Is it eas to fix


When a connector burns out its mainly from a insufficient connection to the load itself,especially the ground,

Nov 08, 2012 | GMC Cars & Trucks

2 Answers

2003 GMC Envoy low beam head lights will not come on. The bulbs are not blown, fuse's ok, no power coming to the head light connector. minimal power to the fuse compartment with fuse removed. 9 to 10...


The problem is a Headlight module. Fuse box under the hood has two black modules side by side, the one on your right is the headlight module the one on the left is the fan module. Try swapping them, if the headlights work replace bad module, don't drive vehicle with the bad module in the fan slot. Mine kept going bad because I had a high intensity bulb on one side.

Oct 02, 2011 | 2003 GMC Envoy

1 Answer

My headlights went out dont know what the problem is low beam dont work high beams works


it may be the dimmer switch located on the base of the steering colume that is not working on the low beam side.also the headlights themselves may need changing if the low beam filament is burnt out and you didn`t realize one was burnt out then the other one burnt out.if that`s not the case then it could be a bad connection at the plug connector for the low beam or for some reason power is lost between the switch and the headlight.you don`t say if this has day time running lights,if it does then it could be the drl relay that is bad.

Apr 21, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

Euro low beam right side brighter than left side


You have a bad ground on the left low beam. Using a test light connected to ground see what wire is positive with low beams on. Using a piece of electrical wire connect one end to ground and with the headlight connector connected to the headlight and headlights on stick the other end into back of the connector at the ground wire. If the light gets brighter, you can cut the original ground wire to the connector ( 2-3 inches from headlight connector) and run a new wire from ground and connect it to the wire at the connector. Hope this is helpful.

Jun 21, 2009 | 1994 Honda Civic

2 Answers

Low beam headlight not working


Headlight's are not fused, there is a circuit breaker built into the headlight switch, pull the head light switch out and look for a burnt discolored connector and discolored terminals on the switch, if u find either or both replace the headlight switch and the connector, headlight switch connectors are avail in the aftermarket through full service parts stores like NAPA, also on the internet under automotive electrical repair connectors, if the headlight switch checks ok and has power in to it and out to low beams then replace the multifunction switch opn the steering column.

Nov 14, 2008 | 1993 Chevrolet K1500

2 Answers

Dashboard, right side headlight and tail lights are not working


All My lights work the dashlights, headlights, tail lights, turn signals and revers, but not my right side running lights the left side works???

Jul 27, 2008 | 1994 Volkswagen Jetta

Not finding what you are looking for?
2007 Pontiac Grand Prix Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...