Question about 1997 Chevrolet Malibu

Open Question

Evap canister replacement - 1997 Chevrolet Malibu

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

How do I replace the purge valve on 2006 Yukon Denali


Replacing Vent Valve Solenoid Purge Valve Solenoid EVAP Valve 2005 GMC...

Remove the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement . Remove the evaporative emission (EVAP) line from the canister purge solenoid, perform the following:
2.1.
Push the large size white retainer portion in.


2.2.
Push down, while pulling up slightly in order the disengage the tube.


Disconnect the EVAP canister purge solenoid electrical connector (1).
Remove the EVAP canister purge solenoid bolt (2). Remove the EVAP canister purge solenoid (3) and insulator (1).

Sep 19, 2015 | Cars & Trucks

1 Answer

I have a 1999 oldsmobile aurora, northstar motor. I was told I need to replace my purge valve solenoid. Can someone please tell me where it is located?


It's under the plastic cover on top of the engine . Remove the intake manifold top cover.
Remove the solenoid quick-connect hose (3) at the EVAP canister purge solenoid (4). Remove the solenoid quick-connect hose (7) from the EVAP canister purge solenoid (4) to the enhanced EVAP service port (8). Remove the electrical connector (6) at the EVAP canister purge solenoid. Remove the EVAP canister purge (2) solenoid valve bolt. Remove the EVAP canister purge solenoid tab from the bracket (5).

Aug 06, 2015 | 1999 Oldsmobile Aurora

1 Answer

P1655 came up on diagnostic test for my 1997 Pontiac grand prix. What is it and where is it located on engine? How much is it gonna cost?you


It could just be a electrical problem !
A DTC P1655 set indicates an improper voltage level has been detected on the EVAP canister purge solenoid circuit , Can you check electric circuits with a volt ohm meter ?
Diagnostic Aids
Check for the following conditions:
?€¢
Poor connection at PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection.


?€¢
Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition ON and observe a voltmeter connected to the EVAP Canister Purge solenoid driver circuit at the PCM harness connector while moving connectors and wiring harnesses related to the EVAP Canister Purge solenoid. A change in voltage will indicate the location of the fault.


Test Description
The numbers below refer to the step numbers on the Diagnostic Table.

  1. Normally, ignition feed voltage present on the output driver circuit with the PCM disconnected and the ignition turned ON.

  2. Checks for a shorted component or a short to B+ on the output driver circuit. Either condition would result in a measured current of over 1.5 amps. Also checks for a component that is going open while being operated, resulting in a measured current of 0 amps.

  3. Checks for a faulty EVAP canister purge solenoid.

  4. This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming
Step
Action
Value(s)
Yes
No

1

Was the Powertrain On-Board Diagnostic System Check performed?
--
Go to Step 2
Go to Powertrain On Board Diagnostic (OBD) System Check

2
  1. Ignition OFF, disconnect the PCM.
  2. Ignition ON.
  3. Using DMM (J 39200), measure voltage between the EVAP canister purge solenoid driver circuit at the PCM harness connector and ground.
Is voltage near the specified value?
B+
Go to Step 3
Go to Step 6

3
  1. DMM to 10 amp scale, install DMM to measure current between the EVAP canister purge solenoid driver circuit and ground.
  2. Monitor the current reading on the DMM for at least 2 minutes.
Does the current reading remain between the
specified values?
0.1 amp - 1.5 amps
Go to Step 11
Go to Step 4

4
  1. Disconnect the EVAP canister purge solenoid (leave the PCM disconnected).
  2. Using DMM, measure voltage between the EVAP canister purge solenoid driver circuit and ground.
Is voltage at the specified value?
0V
Go to Step 14
Go to Step 5

5

Locate and repair short to voltage in the EVAP canister purge solenoid driver circuit (refer to Engine Electrical).
Is action complete?
--
Go to Step 16
--

6

Check the ignition feed fuse for the EVAP canister purge solenoid.
Is the fuse blown?
--
Go to Step 7
Go to Step 8

7

  1. Locate and repair short to ground in ignition feed circuit for the EVAP canister purge solenoid. Refer to Fuse Block Details in Electrical Diagnosis.
  2. Replace fuse.
Is action complete?
--
Go to Step 16
--

8

  1. Disconnect the EVAP canister purge solenoid.
  2. Ignition ON, measure voltage between the ignition feed circuit for the EVAP canister purge solenoid and ground.
Is voltage near the specified value?
B+
Go to Step 9
Go to Step 13

9

  1. Check the EVAP canister purge solenoid driver circuit for an open or a short to ground.
  2. If a problem is found, repair the EVAP canister purge solenoid driver circuit.
Was a problem found?
--
Go to Step 16
Go to Step 10

10

  1. Check the EVAP canister purge solenoid driver circuit and the ignition feed circuit for a poor connection at the EVAP canister purge solenoid and at the PCM.
  2. If a problem is found, replace faulty terminal(s).
Was a problem found?
--
Go to Step 16
Go to Step 14

11

  1. Ignition OFF, reconnect the PCM and disconnect the EVAP canister purge solenoid.
  2. Ignition ON, connect a test light between the EVAP canister purge solenoid driver circuit and the ignition feed circuit at the EVAP canister purge solenoid harness connector.
  3. Using the scan tool outputs test function, cycle the EVAP canister purge solenoid ON and OFF.
Does the test light flash ON and OFF?
--
Go to Diagnostic Aids
Go to Step 12

12

  1. Check the EVAP canister purge solenoid driver circuit for a poor connection at the PCM.
  2. If a problem is found, replace faulty terminal.
Was a problem found?
--
Go to Step 16
Go to Step 15

13

Locate and repair open in ignition feed circuit to the EVAP canister purge solenoid. Refer to Engine Electrical.
Is action complete?
--
Go to Step 16
--

14

Replace the EVAP canister purge solenoid.
Is action complete?
--
Go to Step 16
--

15
Replace the PCM.
Important: Replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming .
Is action complete?
--
Go to Step 16
--

16

  1. Ignition ON, engine OFF, review and record scan tool Fail Records data.
  2. Clear DTCs.
  3. Operate vehicle within Fail Records conditions as noted.
  4. Using a scan tool, monitor SPECIFIC DTC info for DTC P1655.
Does scan tool indicate DTC P1655 failed this ignition?
--
Go to Step 2
Repair complete

Apr 08, 2015 | Pontiac Cars & Trucks

3 Answers

WHAT DOES FAULT CODE P1446-00 MEAN


older nissan? evap canister purge fault. check for loose or rotten/disconnected vacuum hoses before testing the vapor canister purge valve.
25439609-xipalmoknr3fbjmp51kycajc-2-0.jpg The charcoal canisters also clog up. Do some diagnosing before you go changing parts.

Feb 16, 2015 | Cars & Trucks

3 Answers

2000 Ford Expedition My Expedition (4.6L V-9 2WD) has had an intermittent problem of cutting out. The Check Engine light was not coming on - so I figured it is not a misfire. It drove just like it had...


Continuous Memory Diagnostic Trouble Code (DTC) P0446 or P1450 indicates that Self-Test has detected the Evaporative Emission Control System has excessive fuel tank vacuum. Also, a DTC P0446 indicates a vent control malfunction.

Possible causes:

EVAP canister purge outlet tube (EVAP canister purge valve to EVAP canister) blockages or kinks.

EVAP canister tube (fuel tank to EVAP canister) blockages or kinks.

Fuel vapor elbow on EVAP canister contaminated.

Restricted EVAP canister.

Canister vent (CV) solenoid stuck closed (partially or fully).

Plugged or contaminated CV solenoid filter.

EVAP canister purge valve stuck open.

Fuel filler cap stuck closed (no vacuum relief).

VREF circuit open in fuel tank pressure (FTP) sensor.

Damaged FTP sensor. (fuel tank pressure)

Check for kinks or bends in the fuel vapor hoses/tubes (EVAP canister purge outlet tube and EVAP canister tube).

Visually inspect EVAP canister inlet port, CV solenoid filter and canister vent hose assembly for contamination or debris.

Check CV solenoid filter for blockage or contamination.

The common things I've seen are are mud in the canister and the canister vent solenoid being shot or the wiring to the canister vent solenoid being torn off. The resistance of the solenoid should be 48-65 ohms..
Pick up a Chiltons book and will give you a diagram of where exactly you find the canister. They are like $15 at any auto store. Good luck

May 22, 2011 | 2000 Ford Expedition

2 Answers

P1443 code problem. How do I fix this?


P1446 - EVAP Canister Vent Control Valve Close
EVAP canister vent control valve remains closed under specified driving conditions.

This solenoid valve responds to signals from the ECM. When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.

This solenoid valve is used only for diagnosis, and usually remains opened. When the vent is closed, under normal purge conditions, the evaporative emission control system is depressurized and allows EVAP Control System (Small Leak) diagnosis.

The EVAP canister vent control valve is located on the EVAP canister and is used to seal the canister vent.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

About the possible causes that your must solved:
- EVAP control system pressure sensor and the circuit
- Blocked rubber tube to EVAP canister vent control valve
- EVAP canister vent control valve
- Water separator
- EVAP canister is saturated with water


Hope this helps.

Apr 27, 2011 | Mercury Cougar Cars & Trucks

1 Answer

Po 442 po 455


P0442 - Evaporative Emissions System Leak Detected (Small Leak)

P0455 - Evaporative Emissions System Leak Detected (Gross Leak)

This diagnosis detects leaks in the EVAP purge line using engine intake manifold vacuum. If pressure does not increase, the ECM will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition. The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Causes:
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve
- Leak is in line between intake manifold

Solutions:
- Re-tighten or replace fuel tank filler cap
- Replace damaged or leaking EVAP canister
- Replace damaged or leaking lines.

Feb 10, 2011 | Chrysler Town and Country Cars & Trucks

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

1 Answer

CAN YOUR CAR CATCH ON FIR DUE TO EVAP CANISTER


No the evap canister is on the wheel well or the side of the tank. It is a charcole filled canister that handles the evaporation of gas coming through the hoses off the tank. your smelling gas from somewhere else. You need to replace the evap canister.

Mar 29, 2010 | 1998 Pontiac Sunfire

Not finding what you are looking for?
1997 Chevrolet Malibu Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...