Question about 2003 Chrysler Voyager

Open Question

Engine code p1294 - 2003 Chrysler Voyager

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CAN YOU PLEASE TELL ME WHAT THIS CODE MEANS P1294 FROM A SMOG CHECK ON A 1997 DODGE STRATUS


The code is "target idle not reached". This indicates that the idle is too fast and this is what sets the code. The cause could be the TPS or the IAC, but normally if these were the problem, you would have additional codes to indicate them.. The P1294 without any other code is most likely going to be caused by an intake leak, one that occurs after the MAF sensor if your car has one, or the throttle body if not.

Mar 13, 2015 | Dodge Cars & Trucks

1 Answer

What does code P1294 mean?


see http://engine-codes.com/

Possible causes
- Vacuum leak
- Throttle cable not free
- Idle speed screw misadjusted

Reason.
The Engine Control Moduel (ECM) has detected idle speed not within specified range




Feb 18, 2015 | 2001 Dodge Grand Caravan

1 Answer

Error code P1294


I need the model and engine size. P1294 in general is idle control valve or motor slow or no response. Inspect the wire harness and connector to the IAC motor. inspect the wire harness for short to ground. Replace IAC motor

Apr 16, 2014 | 2004 Jeep Grand Cherokee

1 Answer

P1294


your idle it too low you have a vacuum leak. check with a vacuum gage

Jan 21, 2014 | 2002 Dodge Durango

1 Answer

P1294


EGR valve , either the valve is malfunctioning, or the electronic control is...

Jun 19, 2012 | 1999 Chrysler Cirrus

1 Answer

ROUBLE CODE P1294


The code P1294 means that the computer is setting a target for the engine to idle at and the engine cannot do it therefore setting the DTC. Start by checking or replacing the spark plugs and wires. Try to use Autolite spark plugs. Also remove the idler motor from the throttle body and spray it out with carb cleaner. Also spray out the passages in the throttle body that the idle motor use. If that does not fix it you could have another problem like a bad idle motor or something relating to that circuit.

Jan 18, 2012 | 1996 Dodge Neon

1 Answer

What does the P1294 Manufacturer Specific Code mean in a failed Emissions OBD Test?


P1294 Target idle not reached this is the code in the chrysler list of codes for this number and reading it ,it must mean the idle isnt correct when engine is warm but i could be wrong here in my interpretation as our europeon test puts a probe up the exhaust and the idle doesnt come into the equation .So long as the gas output from the engine is below the specified limits on first run at 2500 rpm then idle is read but this is only for the CO and oxygen levels in the exhaust gas as the level of CO2 will depend on the size of the engine but must be below 2% on idle ,so a big monster american gas burner will still be below the 2% by volume on idle but rise with the increase in engine RPM .Complicated business and costly when the cat goes

Mar 25, 2011 | 1999 Jeep Grand Cherokee

1 Answer

Code p1294 03 sebring


P1294 verbiage is simply "Target Idle Not Reached (+/-200 RPM)" which unfortunately is one of the DTC's that is least helpful. The most likely cause of this is a simple vacuum leak, very possible a leaking gasket at the base of the throttle body. What happens is unmetered air enters the engine confusing the PCM, forcing the IAC to chase the idle speed up and down. The first thing you should do is look under the hood and verify that all of the vacuum hoses are connected and in good shape, the brake booster isn't leaking and finally get a can of carb cleaner and go hunting for a leak. If you haven't done this before I recommend letting someone who is comfortable with the procedure do it for you or show you how.

Nov 27, 2009 | 2003 Chrysler Sebring

2 Answers

Target Idle Not Reached (Chrysler, Jeep)i am getting a dash display code of p1294. how do i find the problem? I did find a vacuum line broke and fixed but the error came back!


The code P1294 means that the computer is setting a target for the engine to idle at and the engine cannot do it therefore setting the DTC. Solution start by checking or replacing the sparkplugs. Also remove the idler motor from the throttle body and spray it out with carb cleaner. Also spray out the passages in the throttle body that the idle motor use. If that does not fix it you could have another problem like a bad idle motor or something relating to that circuit. Did you replace the TB or make an adjustment to the TPS?

Sep 22, 2009 | 2003 Jeep Wrangler

Not finding what you are looking for?
2003 Chrysler Voyager Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...