Question about Ford Freestar

Open Question

Instrument cluster reset

Instrument cluster lighting up

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 231 Answers

SOURCE: instrument lights are out

could be a short in the wiring or you could need a new head lite switch.

Posted on Oct 09, 2008

frankzen
  • 19 Answers

SOURCE: My bmw 318is instrument cluster doesnt work

Common problem on BMW's apparently...there are on-line repair services but they are NOT cheap...100-300 bucks. Tough to fix yourself...unles you are a highly skilled techie!

Posted on May 06, 2009

wiringlunati
  • 576 Answers

SOURCE: instrument cluster bulb is out. how do i replace

It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.

Posted on Dec 22, 2009

  • 1 Answer

SOURCE: instrument cluster problems

my 1998 cadillac deville information display cluster goes on and off for days at a time. most times I do not know how fast I am going or miles.

Posted on Dec 27, 2009

  • 10 Answers

SOURCE: Instrument cluster not working

if its not a fuse. try a relay. itll be under the hood in a little box. if thats not it than it could be a short in the wiring.check your running lights as well. most of the time they are ran on the same fuse so if one doesnt work the other one probably wont. also if you have recently replaced your stereo. check over the wiring on it because something could have got loose.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a2000buick century odometer not working


You would need to take it to the dealer or someother qualified repair shop that has the diagnostic tool to check for DTC'S - diagnostic trouble codes in the instrument cluster .
DTC B0570 Season Odometer Malfunction

The instrument cluster receives a vehicle speed input from the vehicle speed sensor (VSS) over the Class 2 line. This signal is used in order to drive the speedometer and the odometer of the instrument cluster. The instrument cluster will compare the VSS data with a 16-point look-up table in order to determine needle deflection. A smooth filter is used in order to secure a continuous response. The season odometer displays the total accumulated kilometers (miles) of the vehicle. This value is permanently stored in the Electronically Erasable Programmable Read Only Memory (EEPROM) of the instrument cluster. The trip odometer displays the accumulated kilometers (miles) to the tenths of a kilometer (mile) since the last reset. This value is stored in Keep Alive Memory (KAM) of the instrument cluster.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
Always perform the Instrument Cluster Diagnostic System Check before attempting to diagnose this DTC.
This diagnostic procedure requires using a scan tool.
This repair procedure requires instrument cluster replacement.
Step
Action
Value(s)
Yes
No
1
Did you perform the Instrument Cluster Diagnostic System Check?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Instrument Cluster
2
Using a scan tool, clear the instrument cluster DTC and retest for DTC B0570.
Does DTC B0570 reset?
--
Go to Step 3
Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.1L or Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.8L
3
Replace the instrument cluster. Refer to Instrument Cluster Replacement .
Is the repair complete?
--
System OK
Go to Diagnostic System Check - Instrument Cluster
© 2017 General Motors Corporation. All rights reserved.

Feb 27, 2017 | 2000 Buick Century

1 Answer

I just bought a 1998 Pontiac Bonneville and now the system monitor light is on why and what does that mean?


No other messages in the driver info center ?
This section provides an overview of the instrument cluster operation as well as a detailed diagnosis. The instrument cluster serves as the primary interface for the vehicle's driver.
The instrument cluster contains a microprocessor as part of the instrument panel assembly. The instrument cluster performs the following functions:
• Recognizes operational malfunctions
• Alerts the driver through indicators
• Stores DTCs which identify malfunction areas
In order to perform all of these functions, the instrument cluster microprocessor has its own inputs, outputs and program software. The instrument cluster has the capability to diagnose malfunctions in the following components:
• The sensors
• The input switches
• The components
• The systems the instrument cluster communicates with or controls
When the instrument cluster or another microprocessor-controlled module detects a malfunction, the instrument cluster may turn on an instrument cluster indicator in order to alert the driver that a malfunction has occurred. Some indicator lamps have dual controls. Your best bet is have it checked for DTC'S diagnostic trouble codes !

Mar 02, 2016 | Pontiac Cars & Trucks

1 Answer

After disconnect and reconnect the battery of my opel antara, the indication of odometer displays only 888... for all indications. How can i reset it?


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2007 Opel Antara 2.0

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2005 Nissan Almera 1.5

1 Answer

How to replace the dashboard bulb in a 1999 plymouth voyager


Which light is out? Is it an instrument cluster light, or one on the temperature or A/C cluster? It it's an instrument cluster light, here is the process: (I'm assuming the 99 is similar to the 98) Remove the bottom dash panel under the steering wheel, remove the instrument cluster cover around the steering column. This will reveal the screws that hold your instrument cluster cover in place. Remove this cover and you can then see and remove the 4 screws holding your instrument cluster in place. Pull your instrument cluster out, remove the main wire connector, then you have access to all the instrument cluster lights on the back side. Hopefully you remember which one is out!

Aug 23, 2011 | 1999 Plymouth Voyager

1 Answer

Hello, we replaced the instrument cluster light bulbs on my 1997 Ford F150. As part of the operation we removed the dials on the instrument panel (didn't need to do that!) now all of the dials read...


no there isnt a way to reset the the instrument cluster back to zero if your talking about how many miles the vehicle has travelled in its lifetime...you will have to remove the dials and reposition them again...either tht or take it to ford and get some proffesional assistance...

Jan 16, 2011 | 1997 Ford Ranger SuperCab

1 Answer

Insturmentation panel lights fuse blows when i start car


Try to remove the instrument panel and disconnect the harness to see if doing that gets rid of the blown fuse when starting the car. If it does, then the instrument panel should be replaced with another. If the fuse still blows when starting, then there is a wire shorted to ground somewhere.
---
Instruments and Switches Instrument Cluster Removal & Installation To Remove:
  1. Remove the instrument cluster trim plate.
  2. Remove the instrument cluster mounting screws.
  3. Rotate the instrument cluster rearward and lift up on the top of the cluster in order to disengage the locating pins.
  4. Disconnect the electrical connectors from the instrument cluster.
  5. Remove the instrument cluster.
To Install:
  1. Connect the electrical connectors to the instrument cluster.
  2. Position the locating pins to the holes in the instrument panel.
  3. Install the instrument cluster by rotating the top inward.
  4. Install the mounting screws.
  5. Install the trim plate.
prev.gif next.gif

Nov 09, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

1 Answer

Turn the key on and the instrument cluster wont light up or allow it to start push a reset button under hood lever and makes no difference


If the car starts but the instrument panel does not lit, then check ignition, instrument cluster connector and instrument cluster.
If the car also does not start , then check ignition, ignition switch, and wiring.

Jun 29, 2009 | 1994 Hyundai Excel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...