Question about 2004 Toyota Camry

1 Answer

Broken driver mirror

The casing around the mirror is broken off with the mirror. but the arm and wires are still attatched.

Posted by on

  • Michael Grey
    Michael Grey May 11, 2010

    Do you still have the broken assembly?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

You can epoxy it back together if it did not shatter otherwise buy a used one from your local junk yard it's simple to replce and has only three screws holding the mount on, you can also buy paint from the dealer to get it to match the rest of your car.

Posted on Jun 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2002 VW Jetta GL - Window & Mirror Controls no longer functioning

Check the wire bundle coming in to the door at hinge side. It is a short or broken wire

May 17, 2014 | Volkswagen Jetta Cars & Trucks

1 Answer

I have an 05 Hyundai Tiburon GT and the top side mirror housing is loose, but the whole housing is attatched to the door of my car. How can I tighten the top housing that holds the mirror?

Each Tiburon has an interior triangle cover (some with tweeter speakers in them), They are easily popped of using a small screw driver so you can access/see the three 10mm nuts holding the outside mirror to the door. When you inspect the fasteners (10mm nuts), check to see if each is tight (not loose). You may find that the one at the top could be broken.... the only solution then is replace the mirror (it'll probably have to be painted if you do replace it).

Jun 10, 2011 | Hyundai Tiburon Cars & Trucks

1 Answer

I have a 2006 Kia Sorento. The driver side view mirror got cracked in a minor accident. Only the mirror got cracked, but the entire casing is still in-tack. Do I need to replace the whole casing or can I...

Any shop that replaces windshields can replace just the glass in your mirror usually for around $25-$35. It's not a hard job and it takes about 20 minutes. They might even do a little better on the price if you don't need a receipt. You can do it yourself if you can get the mirror. You need some silicone adhesive, electrical tape and a couple of wood or plastic blocks.Clean all the broken mirror out and clean the glue off in the case. Run a bead of silicone around the inside of the new glass about 1-2 inches from the edge and put a couple of dabs in the center part. If your silicone is too close to the edge, when you press the new mirror on the glue will squeeze out and glue the mirror to the case. Press the new mirror into the case and wrap the electrical tape around the case and over a block on the face of the mirror. You want the tape pulled a little tight so it puts pressure on the glass but not tight enough to break it. Do this on each end of the mirror and leave it for 24 hours, then remove the tape and blocks. Hope this helps.

Dec 13, 2010 | Kia Sorento Cars & Trucks

1 Answer

My driver side mirror is knocked out by someone. The problem is that it has been broken by the holder supporting the whole case and the mirror. It is hanging by wires so can you please tell me how to...

you will have to buy a new one or get a used one from a wrecking yard. They are sold online. If the old one is painted to match the car, you will also need to get the new one painted. :o(

Oct 10, 2010 | 2006 Mitsubishi Lancer

1 Answer

Passenger side view mirror broke and trimming around window

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door.

As for the trim, you should just be able to wedge it back in place into the door

Jul 30, 2009 | 2003 Toyota Corolla

1 Answer

Can't open driver side door from outside--only the inside--I need to know how to get paenl off to get to door latch--or how to fix the problem

undo all fittings on door trim [arm rest] etc.
panel has pressure plugs so be carefull pulling on the trim to release it from the door!
somtimes you may just have to wiggle a bit
so start on the corner first& work it loose all the way around
check the rodsto the door handle & lock mechanism is still attatched or thtat the handle has broken off the tab that moves the rod

Jul 18, 2009 | Volvo 240 Cars & Trucks

1 Answer

Replacing the mirror with out removing the whole mirror 97 jeep

most mirror glass pops out it has plastic clips on back of glass. first practice on broken one take a flat head screw driver and use rag to protect paint pry around glass to release but be gentle at the same time hope this helps u

Apr 03, 2009 | 1997 Jeep Grand Cherokee

2 Answers

How do i remove and replace the driver's side mirror?

If the metal pivot arm is not broken you can just replace the glass and plastic housing. To remove the glass you tilt the glass down towards the floor and use a wide plastic or wood bladed object to prise from behind, the glass should pop off from its clips. Remember to catch it if its not damaged. To remove the housing once the glass is out you need to look underneath the mirror unit, there you will find a small plastic bung, gently prise it out and then use a long small flat bladed screwdriver straight up inside the hole and lever towards the front of the car whilst lifting straight up on the plastic housing, this should then lift off. To replace just slot the new housing on and click into place then fit the glass back, remember to connect the wires first if it is a heated glass.
If the metal pivot arm is broken then you will find the remaining screws behind the plastic trim inside the vehicle.

Oct 26, 2008 | 1998 Volkswagen Beetle

2 Answers

2002 c class, mirror

you can google an exploded view of your wiring harness that leads to the wring of your mirror. However this will probably not be a compatible way of doing it. The mirror is disigned differently.

Sep 04, 2008 | 2007 Mercedes-Benz C-Class

Not finding what you are looking for?
2004 Toyota Camry Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

81342 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides