Question about 2000 Cadillac Catera

1 Answer

COMPUTER RELEARN PROCEDURES - 2000 Cadillac Catera

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Cadillac Master
  • 880 Answers

Computer will relearn at it's own pace while driving. no input needed from the driver.

Posted on Jun 03, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After completing the 45 minute relearn procedure for a 2004 Pontiac Grand Prix message center Now says system not programmed


Relearn for what ? Anti theft system PK3 ? The relearn procedure is three 10 min. procedures for a total of 30 min.
30-Minute Relearn Procedure
Use this procedure after replacing the following components:
?€¢
The passkey III (PK3) keys


?€¢
The BCM


?€¢
The PCM, see important above

Important: This procedure is not available on vehicles equipped with option code (Z49).
If replacing a BCM with an GM SPO Replacement Part, perform the procedure to setup a new BCM prior to the 30-minute relearn procedure.

  1. With a master passkey III key, turn ON the ignition, with the engine OFF.
  2. Observe the STARTING DISABLED DUE TO THEFT message on the drivers information center (DIC), after approximately 10 minutes the STARTING DISABLED DUE TO THEFT message on the DIC will turn off.
  3. Turn OFF the ignition, and wait 5 seconds.
  4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.
  5. Important: The vehicle learns the key transponder information and/or passwords on the ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
  6. With a master passkey III key, start the vehicle. The vehicle has now learned the key transponder information and the PCM has now learned the fuel continue password.
  7. With a scan tool, clear any DTCs.

Dec 07, 2015 | Pontiac Cars & Trucks

1 Answer

After disconnecting and reconnecting the battery the engine does not run smoothly again. What causes this problem? How can I solve this problem?


Battery Disconnect or Replacement Problems Here read this , you erased learned values in the engine computer . You just have to drive the vehicle so it can relearn ! An in some cases you need to take to the dealer to have relearn procedures done !

Aug 16, 2015 | Cars & Trucks

1 Answer

How do you change imrc on 2007 jeep compass


try reading the FSM? yet

or at alldata.com for 15 bucks?

it all there, every day ,all the time. no need to wonder.

or join jeep forum.?

it unscrews,

and screws back on.

but the real question is, is it needing calibration. during or after.

replacing it is childs play, youtube that, bingo?

did you do all 25 test in the FSM, yet, on iRMC

even making sure the flapper is not jammed??????

if yes, and the actuator is really bad,

read this in the last page .



If the Manifold Flow Valve is replaced, a non volatile memory reset must be performed to learn the new port flap adaptive values.



now more lil\'horrors.. see what happens if you jerk the battery

quote

Vehicles equipped with engine and transmission computers may require a relearn procedure after the vehicle battery has been disconnected. Most vehicle computers memorize and store vehicle operational patterns. When the battery is disconnected, the information may be cleared. If the information is cleared, the computer will go into default mode in order to operate the vehicle. The vehicle computer will relearn operational patterns each time the vehicle is restarted. The relearning process may take up to 40 or more key cycles.

When a specific engine component is replaced, a relearn procedure may be required. If the relearn procedure is not performed, the vehicle may exhibit the following:




  • Harsh or poor shift quality


  • Poor fuel mileage


  • Hesitation or stumble


  • Unstable idle or stalling


  • Lean or rich running conditions


If an accessory component was replaced, a relearn procedure may also be required. The following systems and components may not work properly without a relearn procedure:




  • Anti-theft system


  • Steering system


  • Power window system


  • Power sunroof system


It is important to reset any Diagnostic Trouble Codes (DTC\'s) before performing the relearn procedure. Most relearn procedures can be performed with the use of an OBD-2 scan tool.






NOTE




This reconnection procedure is to be performed anytime the battery has been disconnected.






  1. Connect the battery negative cable to the battery post and tighten the clamp nut to 45 inch lbs. (5 Nm).


  2. If the vehicle is equipped with Electronic Stability Program (ESP), once the battery is reconnected, the Steering Angle Sensor (SAS) in the clockspring needs to be calibrated.




    NOTE




    The SAS requires calibration anytime the battery or an ABS (ESP) component has been disconnected for any length of time. If the SAS is not calibrated following battery reconnection, the ESP/SAS indicator lamp is illuminated following 5 ignition cycles indicating the need for calibration.






  3. To calibrate, perform the following:


  4. Start the engine.


  5. Center the steering wheel.


  6. Turn the steering wheel all the way to the left until the internal stop in the steering gear is met.


  7. Turn the wheel all the way to the right until the opposite internal stop in the steering gear is met.


  8. Center the steering wheel.


  9. Turn off the engine.


SIGH !

Jul 15, 2014 | 2007 Jeep Compass Limited

1 Answer

What does codes p0700 and p0605 means on a 2001 pt cruiser


Both diagnostic troubhle codes (DTC's) mean the same thing. There are really no testing procedures listed but look at your connectors and wires. Now for the bad news...P0605 & P0700 means there is internal problem with your transmission control module and in 99 percent of the cases it means replacement of the TCM. They do need to be programed afted installation. 2 procedures need to be performed. One is called a pinion factor and the other is called a relearn or quick relearn procedure and they do require the proper diagnostic computer equipment. The TCM is located behind the splash guard on the front left (drivers side wheel. Once you remove the tire and splash guard it is mount to the frame rail and has a 60 pin connector plugged into it. Wish it was better news but hope this helps clearify what the codes mean....

Jul 01, 2013 | Cars & Trucks

1 Answer

Procedures for idle speed relearn for 2007 pontiac torrant


Is the free instructions explaining the idle speed relearn for a 2007 pontiac torrent?

Dec 29, 2012 | 2007 Pontiac Torrent AWD

1 Answer

Computer relearn procedures Actros truck


HOW WE WILL CHANGE SPEED OF ACTROS TRUCK

Apr 11, 2012 | Cars & Trucks

1 Answer

My car wont reverse or go on drive.....have changed computer box.... please suggest fix


O did you have it flashed by the dealer ..and do the drive cycle relearn procedures..????

May 07, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

Anti theft


hi , not necessarily , did you replace the key and tumbler , or the ignition switch (electrical part) ? there is a password relearn procedure , attempt to start the vehicle , leave ignition on until THEFT SYSTEM indicator turns off , (approximetly 10 minutes) , turn ignition switch off , attempt to start vehicle , if vehicle starts , password has been learned ... if password does not relearn , i can post some diagnostic procedures .

J5

Jan 21, 2009 | 1998 Pontiac Sunfire

Not finding what you are looking for?
2000 Cadillac Catera Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...