Question about Cars & Trucks

Open Question

What is the torque specification for a harmonic balancer on a 97 Infiniti qx4

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: tryen to find location of the crank sensor on 1998 infiniti QX4

looking for crankshaft sensor on 1998 infiniti qx4

Posted on Nov 17, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the torque converter clutch solenoid?


The torque converter is inside the transmission. The (electric) clutch solenoid - usually - is on the outside of the transmission case.

Get a flashlight, get under the vehicle and look on the transmission case for electrical wires..

The link below will give you a general idea of what it may look like:

Transmission Control SolenoidsFor Infiniti J30 M30 Q45 and QX4

Feb 24, 2016 | 2001 Infiniti QX4

1 Answer

How to replace crankpully on 3300 olbs


The harmonic balancer on these engines is now press fit onto the crankshaft and requires the use of Tool J-38197 for removal. The torque specification to be used during installation has also been revised. The procedure to be used when replacing the crank sensor is as follows:

REMOVAL






  1. Disconnect serpentine belt from crankshaft pulley.


  2. Raise vehicle on hoist.


  3. Remove right front tire and wheel assembly.


  4. Remove right inner fender access cover.


  5. Using 28 mm socket, remove crankshaft harmonic balancer retaining bolt.


  6. Remove crankshaft harmonic balancer using Tool (J-38197).


  7. Remove foreign object deflector (DO NOT use pry bar).


  8. Disconnect sensor electrical connector.


  9. Remove sensor and pedestal from block face.


  10. Remove sensor from pedestal




INSTALLATION






  1. Loosely install crankshaft sensor on pedestal.


  2. Position sensor with pedestal attached on Tool J-37089.


  3. Position tool on crankshaft.


  4. Install bolts to hold pedestal to block face, torque to (18-26 lb. ft.).


  5. Torque pedestal pinch bolt to (26-44 lbs. in.).


  6. Remove Tool J-37089.


  7. Install foreign object deflector.


  8. Place Tool J-37089 on harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.


  9. Install balancer on crankshaft.


  10. Apply thread sealer GM #(NNN) NNN-NNNNor equivalent to threads of crankshaft balancer bolt. Torque bolt to + 56 degrees (104 lb. ft. + 56 degrees).


  11. Install inner fender shield.


  12. Install tire and wheel assembly. Torque lug nuts to (104 lb. ft.).


  13. Lower vehicle.


  14. Install serpentine belt.
see this vedio

Jul 11, 2014 | 1993 Oldsmobile Cutlass Ciera

1 Answer

How to disarm a 2006 infiniti G35 alarm


I would like to know about this also.
I have a 97 QX4 same thing.

Mar 21, 2013 | 2007 Infiniti G35 Sedan Sport Sedan

1 Answer

PO744 code 2001 infiniti qx4 how do i fix


CODE PO744 AUTOMATIC TRANSMISSION TORQUE CONVERTER CLUTCH SOLENOID VALVE FAULT. POSSIBLE CAUSE FAULTY TCC SOLENOID.CHECK TCC SOLENOID WIRING FOR DAMAGE.OR YOU COULD HAVE FAULTY TCM OR ECM. IF THE TCC SOLENOID IS FAULTY YOUR ENGINE WILL STALL OUT AT A RED LIGHT OR STOP SIGN.YOUR ENGINE WILL STALL OUT AT EVERY STOP THAT WOULD BE SIGN FAULTY TCC SOLENOID.IF ENGINE DONT STALL OUT THE TCC SOLENOID COULD COULD BE STUCK OPEN, IF YOUR TORQUE CONVERTER FAULTY IT WILL CAUSE PREMATURE LOCKUP STALLING OUT THE ENGINE.

Nov 01, 2011 | 2007 Infiniti QX4

1 Answer

About how much do you think it will run me to fix my torque converter clutch on a 1998 infiniti QX4.


If the clutch is bad the transmission will have to be removed and the entire torque converter will have to be rebuilt or replaced so I believe you're looking at $1000 minimum.

Jan 15, 2011 | 1999 Infiniti.5 QX4

1 Answer

How do you replace the harmonic balancer pulley on the 2000 oldsmobile intrigue


The short answer to your question is:

1. Raise the car on the passenger side and remove the front wheel.
2. Remove the belts on the harmonic balancer.
3. Remove the retaining bolt.
4. With a puller, jack the harmonic balancer off of the crank shaft. You can rent a puller at your local auto parts store. It is easiest to access the harmonic balancer through the fender, hence the need to remove the wheel.
5. You should also consider replacing the seal around the harmonic balancer to minimize the possibility of a leak later.
6. Install the new harmonic balancer and tighten the retaining bolt to the specified torque (I don't know this off the top of my head).
7. Replace the belts and wheel, and voila...mission accomplished.

This was a short answer to your question. You may wish to consult a repair manual for illustrations, torque specifications, additional instructions, etc. This job is not for the faint of heart. Good luck!

Feb 19, 2010 | 2000 Oldsmobile Intrigue

1 Answer

Tryen to find location of the crank sensor on 1998 infiniti QX4


looking for crankshaft sensor on 1998 infiniti qx4

Mar 01, 2009 | 2004 Infiniti QX4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...