Question about 1990 Lexus LS 400

Open Question

Torque settings on 1uz lexus v8

I need the torque setting for 1uz lexus v8 plse

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: setting crankshaft and camshaft timing

with crank pulley white mark on 0 remove both cam pulley covers and verify yellow painted notches are exactly on the T mark cast in the fwd cam bearing housings..IF u find that it ISNT 'in time' then remove tensioner located near crank pulley and very carefully manipulate the L and R cam sprokets to allow belt to removed from cam sprockets only... DoNOT rotate engine without T belt installed .Do NOT turn engine backwards.. ever.. be advised that should the cam timing be off by more than 3 teeth either way serious engine damage will result ..this series of engines utilizes variable intake camshaft adjustment .. This job is not for the american small block specialist of yesteryear.. even an experienced asian tech is gonna have a difficult time with this lexus .. its not quite the same engine the Tundra uses...Lexus only mods befuddle reg toyota techs

Posted on Oct 29, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi tel me ill want to connect up a obd2 pluk to 1997 lexus 1uz vvti ecu ill need to no wer the 16 pin wiaers are connect to ecu


The connector will always be in or very near to the driver's footwell. The most common place is tucked up under the trim panel at about knee level.
Open the drivers door wide and look in the footwell. Look underneath where the pedals are connected to the floor, over on the door side. On some models it is near the bonnet release lever.
The photo below is from a Lexus CT 200h but shouldn't be that different.

0fd1532f-f340-4209-9aa6-e74a2808b150-an1gbc1gidp3gbwghi4a0iac-4-0.jpeg

May 18, 2018 | Lexus Cars & Trucks

2 Answers

Timing belt/crank shaft and camshafts


Yes, that may cause it the misalignment of the timing belt, you can try to check it and put everything back in..

Good luck.........

Aug 20, 2008 | 1996 Lexus LS 400

1 Answer

What are the torque settings for valve cover bolts on a 2002 Lexus ES 300?


Do the cross pattern....and little by little.
Service manual calls for 69 in lbf.

Sep 28, 2016 | Lexus Cars & Trucks

1 Answer

Will a power steering pump off a 98 lexus es300 work for a 98 lexus ls400?


best ask a steering specialist shop as the engine identification shows a es300 as a 1mz-fe (3.0 ltr) and a ls400 as a 1uz-fe (4.0 ltr)
there may be mounting differences between the engines

Apr 08, 2016 | Lexus Cars & Trucks

1 Answer

I need torque settings for engine 15B/F 4104cc


Check out the help links mentioned below:----
Cylinder Head Torque Setting http://schematicsdiagram.blogspot.com/2012/10/cylinder-head-torque-setting.html
----------- Lexus LS400: Transmission or Torque Converter? http://technoanswers.blogspot.in/2012/04/lexus-ls400-transmission-or-torque.html

----------
For more help.keep updated.
Thanks.

Oct 15, 2012 | Toyota Cars & Trucks

1 Answer

Cylinder head bolt torque on a Toyota 1uzfe v8?


sir pl z told me Toyota 1uz assamble the head ,so one time i com pleat the trque, than agan the open bold and retired , and pl z bold secvence titnes

Oct 26, 2010 | 1990 Lexus LS 400

1 Answer

I NEED TO KNOW THE FIRING ORER ON THE COILS TO PUT WIRES BACK ON CORRECTLY


For the LS400 1UZ-FE V8 the firing order is 1-8-4-3-6-5-7-2, RH from the front 2-4-6-8, LH from the front 1-3-5-7. The RH/LH of the engine is facing forward, in other words, from the drivers2.gif seat looking forward.

Oct 19, 2009 | 1995 Lexus LS 400

1 Answer

Firing order for a lexls400 1995 v8 2 caps


For the LS400 1UZ-FE V8 the firing order is 1-8-4-3-6-5-7-2, RH from the front 2-4-6-8, LH from the front 1-3-5-7. The RH/LH of the engine is facing forward, in other words, from the drivers seat looking forward.

May 10, 2009 | 1995 Lexus LS 400

1 Answer

Setting crankshaft and camshaft timing


with crank pulley white mark on 0 remove both cam pulley covers and verify yellow painted notches are exactly on the T mark cast in the fwd cam bearing housings..IF u find that it ISNT 'in time' then remove tensioner located near crank pulley and very carefully manipulate the L and R cam sprokets to allow belt to removed from cam sprockets only... DoNOT rotate engine without T belt installed .Do NOT turn engine backwards.. ever.. be advised that should the cam timing be off by more than 3 teeth either way serious engine damage will result ..this series of engines utilizes variable intake camshaft adjustment .. This job is not for the american small block specialist of yesteryear.. even an experienced asian tech is gonna have a difficult time with this lexus .. its not quite the same engine the Tundra uses...Lexus only mods befuddle reg toyota techs

Aug 27, 2008 | 1996 Lexus LS 400

Not finding what you are looking for?
1990 Lexus LS 400 Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

918 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...