Question about 2007 Jaguar XKR Convertible

Open Question

Brake light bulb replacement on 2007 Jaguar xor

Cannot see how to remove the tail assembly to replace a brake light bulb.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnthejag
  • 286 Answers

SOURCE: Rear Brake Light

Hi

In the trunk, just un clip the light cluster, twist out the bulb, and renew the stop bulb, refit the light cluster.

Good Luck !

John.

A FixYa rating would be appreciated please !

Posted on Feb 07, 2009

  • 91 Answers

SOURCE: Rear interior light and door courtesy lights not working- Jaguar

take off the cover and replace them. if you have a volt/ohm meter you can put if on the car side and make sure you have voltage and the ohm meter on the buldb should give a 1 rating if its good. it would be the cheapest and easiest to just get a new bulb and see if it works then start checking fuses if its not the bulb.

Posted on Mar 31, 2009

  • 262 Answers

SOURCE: How do I replace the tail light on my 2004 Jaguar

unsrew the rear panel in your boot then four srews hold the tail light

Posted on Nov 13, 2009

  • 1810 Answers

SOURCE: how to replace headlight bulb on a 2003 jaguar s

push bar clip towards light it is on a hang up bracket one you press in then you push left then right 1 way or the other will pop the clip

Posted on Jan 06, 2010

mpcheeseman1
  • 1400 Answers

SOURCE: how to replace right rear stop and tail light?

Should have acsess to lightbulbs in trunk of car.

Open trunk and remove any carpet or cover around light area.

Bulb should be in a socket,turn socket until it comes out of light lens.

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

No tail lights and only middle and passenger brake light works on my 2001 chevy venture


The tail light assembly on this vehicle is a poor fit and moisture softer invades the bulb assembly when it rains. Remove the tail light assembly and replace any bulbs that have shorted out. You may need to replace the assembly.

Feb 04, 2014 | 2001 Chevrolet Venture

1 Answer

2002 GMC Yukon XL brake light replacement


Hello Weaver124!
Open the tailgate(s) completely and you'll find two phillips-head screws on the inside edge of the tail light assembly. Take out those two screws (keep one hand on the assembly when you remove the last screw) and the whole tail light assembly will come off of the vehicle. On the back side of the tail light assembly, twist and remove the light bulb housing for the blown bulb. The bulbs themselves on some models vary in the manner in which they are removed: (1) If the base on the bottom of the bulb itself is a *round* brass base, press down on the bulb then twist it to remove it, or (2) If the base on the bottom of the bulb itself is *flat* plastic, pull the bulb straight out of the assembly. To replace the bulb, simply reverse the order. Best wishes!

Mar 12, 2011 | 2002 GMC Yukon XL

1 Answer

How to replace LR2 Third Brake Light


The Freelander is Land Rover's entry-level crossover SUV. Unlike other Land Rover vehicles that use a traditional "truck," body-on-frame chassis, the Freelander is built on a unibody, front-wheel drive car chassis. The Freelander is sometimes known in the U.S. as the "LR2."

1 Purchase replacement bulb P21/5W, available at most auto parts stores and at any Land Rover
dealer.

2 Turn off engine and open rear cargo door.

3 Remove the two Torx screws from the side of the tail light assembly. Carefully pull the assembly
away and unplug the electrical harness.

4 Turn the assembly over to access the bulb modules. There are three separate bulb modules; the
top module should be the brake light.

5 Rotate the bulb module counterclockwise to release it from the tail light assembly. Push the bulb
down (into the module) and turn it counterclockwise to remove it from the module.

6 Insert the new bulb into the bulb module. Carefully push the bulb down and turn it clockwise.
Reinsert the bulb module into the tail light assembly and turn it clockwise.

7 Reconnect the electrical harness to the tail light assembly. Remount the tail light assembly and
replace the Torx screws.


Dec 26, 2010 | Land Rover LR2

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

1 Answer

I need to change the brake and tail light on my 1996 toyota corolla . I would need a manuel on that please.


The steps to replace the brake light bulb on a 1996 Toyota Corolla:

The bulb needed is type 1157. After opening the trunk you need to remove the trunk liner on the side (right side for this example)where the brake light bulb is out. The plastic capture grommets hold the liner in place. Once the grommets are removed there is a nut (10mm) that is a bright brass-like color. This needs to be removed. Then on the outside of the trunk on the tail-light lens left side there are two nuts black in color (10mm) they need to be removed. Now the fun starts .... you needto slide the whole assembly back. You will note two black plastic posts on the rear quarter-panel, do not remove these ... these are used to hold the tail-light assembly in place since on the inside of the tail light assembly there are two rod-like protrusions that slide into these brackets. So.... remove the screws and wiggle the assembly back and it "should" slide back so that you can get at the bulb socket hat you twist to remove from the assembly. Now the bulb is visible and you reverse the order of steps to get it all back together .... a miserable design!

Sep 30, 2010 | Toyota Corolla Cars & Trucks

1 Answer

Change rear light bulb


Pull the tail light assembly out.
Owner manual has instruction on how to remove tail light for bulb replacement.

Jul 16, 2010 | 2007 Audi A3

1 Answer

How do you replace brake light bulb on a 2006


you need to remove the 2 torx screws (accessable when you open the tail gate). once they are out, you are able to pull the whole tail lamp assembly out of its position, and then turn the socket counter clockwise to remove it from the assembly. replace the bulb, and reassemble. good luck!

Jun 21, 2010 | 2006 Chevrolet Silverado 1500 2WD

1 Answer

How di i get the tail light assembly of to change the brake light bulb on nisson versa hatchback


open the rear hatch and pull carpet away from the lens you want out,you will see four plastic thumb nuts,remove them and pull lens assembly out and replace your bulb

Jan 22, 2010 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Need to replace rear brake light on a 1999 Buick Park Avenue. How do I remove the plastic lenses or assembly?


you will need to open the trunk and remove the carpet covering the inside where the tail lights are, find 2 or 3 nuts which are probably 8 or 10 mm,so use a socket and ratchet,remove the nuts and pull the tail light asembly out from the back and you will find the tail light bulb sockets. release the little latch/lock clips while turning the socket assembly about 1/4 turn counter clockwise and you can check each bulb. watch where the wire harness for each socket and also the tail light assembly is so you dont pinch or damage the wires when putting the tail light assembly back in. your owners manual may also give you these instructions and will tell you the correct bulbs to use for tail, brake and turn signal lights.

Oct 27, 2009 | 1999 Buick Park Avenue

Not finding what you are looking for?
2007 Jaguar XKR Convertible Logo

Related Topics:

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...