Question about 2012 Mercedes-Benz Sprinter

Open Question

Fault code p1501

Hot film mass air flow sensor what is these

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
eitan
  • 291 Answers

SOURCE: replace air mass sensor

REMOVE SNORKEL AIR TUBES BETWEEN GRILL AND AIR CLEANER. REMOVE ENTIRE AIR CLEANER--(PULL UP FROM BOTTOM OF UNIT, IT IS JUST HELD ON WITH FOUR CLIPS) AT REAR OF ENGINE YOU WILL SEE A ROUND AIR INTAKE THE SENSOR IS IN THE TOP TUBE. USE FLAT BLADE SCREW DRIVER TO PUSH IN THE CLIP AT THE REAR AND REMOVE THE TUBE UNPLUG THE ELECTRICAL CONNECTION. THE SENSOR IS SCREWED IN WITH 2 TAMPER PROOF SCREWS REQUIRING A SPECIAL BIT (5 STAR WITH A HOLE IN THE CENTER) I GOT ONE FROM A TOOL TRUCK (SNAP ON ETC)

Posted on May 15, 2008

Ad
miket756
  • 2702 Answers

SOURCE: engine light and stalling on aceleration, hooked

oh dear, its still that mass air flow sensor playing up, there very easy to damage just one tuch will do it, try another one but be very jentel when you fit it

Posted on Oct 22, 2009

  • 1 Answer

SOURCE: engine diagram for a 2000 Mercedes-Benz C-Class

navigator software download for mercedes benz c 320

Posted on Nov 01, 2009

  • 1619 Answers

SOURCE: 1996 MERC 220 HAS ROUGH IDLE AND POWER LOSS ON

Coils, wires, plugs, fuel filter. A real tune up in other words.

Posted on Apr 14, 2010

michael4wgv
  • 166 Answers

SOURCE: mass air flow sensor where is it located in the

mass air flow is right behind the air filter box if it's a c230 kompressor.

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTC P1095?


P1095 Mass air flow ahead of throttle valve implausible (too high) Possible fault causes: - Hot-film mass air flow meter faulty (battered) - DME control module faulty (ambient pressure sensor at fault detection threshold)

Sep 09, 2015 | Porsche Cars & Trucks

1 Answer

Ok, i have a 2000 sierra 5.3 slt got the p0101 code it wouldnt star up unles i give it some gas and it shots off so, rough idle and wont stay on, i change the MAF sensor (new delphi) but still doing the...


The Mass Air Flow (MAF) sensor is located in the stream of intake air and measures this intake flow rate by measuring a part of the entire intake flow. It is what they call a hot film and is supplied with electric current from the Engine Control Module (ECM).
The temperature of the hot film is controlled by the ECM to a certain extent. The heat generated by the hot film is reduced as the intake air flows around it. The more air, the greater the heat loss. Therefore, the ECM must supply more electric current to maintain the temperature of the hot film as air flow increases. The ECM detects the air flow by means of this current change.
The OBDII people suggest that before you replace the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with compressed air or by using a cleaner on the mass air flow sensor. Truly, all that may be wrong is a build-up of dirt.Unfortunately, in your case, replacing the Mass Air Flow did not work.After replacement, did you reset the code and drive the vehicle?.
I suggest you replace the air filter and check for intake air leaks.YouTube has some good videos on how to do this, one by Eric the car guy and one by Scottie Kilmer https://www.youtube.com/watch?v=9CPqbaSgcokhttps://www.youtube.com/watch?v=zMok2y05jNE

Jan 13, 2015 | 2000 GMC New Sierra 1500

1 Answer

2008 Chevy Kodiak c4500 duramax desiel code reader (Innova 3100 Can OBD2) shows P0102, what does it mean


P0102 Chevrolet - Mass or Volume Air Flow Circuit Low Input

Read more: http://engine-codes.com/p0102_chevrolet.html#ixzz38p5k1ZD8

Possible causes - Faulty mass air flow sensor
- Intake air leaks
- Dirty mass air flow sensor
- Dirty mass air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor circuit poor electrical connection

Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor.


Read more: http://engine-codes.com/p0102_chevrolet.html#ixzz38p5tpWZk

Jul 28, 2014 | Cars & Trucks

1 Answer

2000 nissan sentra 2.0 error codes p0101& p0102


P0102 - Mass Air Flow Sensor Circuit Malfunction

The mass air flownissan-maxima-maf-sensor.jpg or MAF sensor is placed in the intake air duct between the air filter and the engine intake manifold. The MAF sensor measures the amount of intake air flow. The MAF sensor converts the air flow measurement into a voltage or frequency signal, with the voltage or frequency changing proportionally to the amount of air flow. The air flow sensor signal is monitored by the engine computer (ECM). The engine computer (ECM) uses the mass air flow signal to know the engine load and to calculate the proper amount of fuel injected. If the signal from the mass air flow sensor is out of expected range, the ECM detects a fault and sets the code P0100. For example, the mass air flow sensor signal could be higher than expected when the engine is not running or lower than expected with the engine running. A car with the code P0100 may have some driveability issues, such as stalling, lack of power, surging, hesitation, etc. In some cars, the code P0100 can cause the fail-safe mode where the engine speed would be limited to 2,500 - 3,000 rpm.
If there are other trouble codes present, they might need to be looked at first. Checking the freeze frame may help, as it may contain some important information. The freeze frame is a snapshot of the engine parameters at the moment when the fault was detected. The freeze-frame may show whether the vehicle was running or stopped, whether the air-fuel ratio was lean or rich, was the engine was cold or warmed up at the time of the malfunction. Read more about the freeze frame.


Read more about mass air flow sensor.

What could cause the code P0100:
- faulty or contaminated mass air flow sensor
- open or short in the mass air flow sensor electrical circuit
- open or short in the sensor power or ground circuit

- other electrical problem with the MAF sensor wiring, (corroded wires, bent terminals, bad ground connection, burned fuse, etc.
- vacuum leaks
- restricted air flow at or before the air filter
- wrong air flow sensor installed
- problem with ECM





P0102 - Mass Air Flow Sensor Circuit Low

The mass air flow or MAF sensor measures the amount of air entering the engine. The engine computer (ECM) uses the mass air flow signal to calculate the amount of fuel injected (read more how the MAF sensor works below). The code P0102 is set when the signal from the mass air flow sensor is lower than expected. Often a car may exhibit some driveability symptoms, such as lack of power, surging, hesitation on acceleration, hard starting, pinging (detonation), or rough idle when started cold. Often the codes P0171 or P0174 could also be stored along with the code P0102, as the incorrect air flow signal can cause the engine to run lean. The codes P0171 and P0174 indicate a lean condition. Checking the freeze frame might help in the diagnostic process. The freeze frame is stored in the ECM along with the trouble code. The freeze frame contains some recorded parameters (e.g. vehicle speed, engine temperature, fuel trim) at the moment when the fault was detected. The freeze frame can also be accessed with a scan tool.



What could cause the code P0102
- faulty or contaminated mass airflow sensor
- debris blocking the air flow at the mass air flow sensor
- unmetered air leaking past the MAF sensor (vacuum leaks)
- PCV system vacuum leaks
- restricted or collapsed intake air duct
- dirty or restricted air filter
- restricted air screen before the air filter
- improper application of aftermarket components (e.g. cold intake, modified air filter, etc.)
- wrong air flow sensor installed
- electrical problem with the MAF sensor wiring, connector, power supply or ground.
- problem with ECM
- in some cases other issues with the fuel injection system like a clogged catalytic converter or a faulty manifold absolute pressure sensor (MAP) can also cause the code P0102.




Solution for MAF repair

Oct 20, 2012 | 2006 Kia Sorento

1 Answer

P0121


Hi there:This code can also be related to the MAF or mass air flow sensor. Lets test it before we try anything new.
Testing and Inspection:
8_16_2012_9_45_44_pm.gif



MASS AIR FLOW SENSOR (MAF SENSOR)
This hot film type air flow sensor is composed of a hot film sensor, housing, and a metering duct (hybrid, sensor element). The mass airflow rate is measured by detection of heat transfer from a hot film probe. A change in the mass air flow rate will cause a change in the amount of heat being transferred from the hot film probe surface to the air flow. This results in a change in temperature of the hot film probe and a change of resistance.


Circuit Diagram:

8_16_2012_9_47_04_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 16, 2012 | 2001 Hyundai Elantra

1 Answer

Service engine light soon.CodeP0101


Here is the meaning of the code.

P0101 GMC Description The Mass Air Flow (MAF) sensor is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module (ECM).

The temperature of the hot film is controlled by the ECM acertain amount. The heat generated by the hot film is reduced as the intake air flows around it. The more air, the greater the heat loss. Therefore, the ECM must supply more electric current to maintain the temperature of the hot film as air flow increases. The ECM detects the air flow by means of this current change.
Read more: http://engine-codes.com/p0101_gmc.html#ixzz22j2iAwpz

Aug 05, 2012 | GMC Envoy Cars & Trucks

1 Answer

P0101


Here is the definition of the code.

P0101 GMC Description The Mass Air Flow (MAF) sensor is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. It consists of a hot film that is supplied with electric current from the Engine Control Module (ECM).

The temperature of the hot film is controlled by the ECM acertain amount. The heat generated by the hot film is reduced as the intake air flows around it. The more air, the greater the heat loss. Therefore, the ECM must supply more electric current to maintain the temperature of the hot film as air flow increases. The ECM detects the air flow by means of this current change.
Faulty mass air flow sensor
- Intake air leaks
- Dirty mass air flow sensor
- Dirty air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor electrical circuit poor connection
Read more: http://engine-codes.com/p0101_gmc.html#ixzz223ibNx6t

Read more: http://engine-codes.com/p0101_gmc.html#ixzz223i9HR3J

Jul 29, 2012 | 2002 GMC Safari

1 Answer

ISUZU TROOPER 3.2 V6 CODE P0101


P0101 ISUZU - Mass Air Flow Circuit Performancexicon.jpghttp://engine-codes.com/p0101_isuzu.htmlForum CodePossible causes- Dirty mass air flow sensor
- Dirty mass air filter
- Mass air flow sensor harness is open or shorted
- Mass air flow sensor electrical circuit poor connection
- Intake air leaks
- Faulty mass air flow sensor
Tech notes Before replacing the mass air flow sensor, try replacing the air filter and cleaning the air flow sensor with low compress air or mass air flow sensor cleaner. Reset code and drive vehicle. If the code comes back, it may be necessary to replaced the mass air flow sensor

Jul 04, 2012 | 2001 Isuzu Trooper

1 Answer

I got the code from the OBD IT read a code of 23 and one of 36 now i need to find what it means


code 23 is MAT too low.(mass air temp.) code 36 is Mass Air Flow Sensor Error

The ECM receives a signal from the Mass Air Flow sensor depending on the amount of air entering the engine. The ECM uses information from this sensor to help calculate fuel delivery and spark timing.

Fault Code Description

  • 36 - Mass Air Flow sensor error

    Symptoms

    • Engine stalling
    • Lack of power

    Common Problems Faulty Mass Air Flow sensor,Broken wire to Mass Air Flow sensor,Dirty sensing element in Mass Air Flow sensor

      May 17, 2011 | Pontiac Bonneville Cars & Trucks

      2 Answers

      Want to know engine light p0102 code means


      P0102 is the generic DTC (Data Trouble Code) for (Mass or Volume Air Flow Circuit Low Input), and it would most likely be a fault with the MAF (Mass Air Flow) sensor.

      The MAF sensor could be dirty or faulty, and there might even be restricted air flow to the MAF sensor (like a plugged up air filter). Also be sure that there are no air or vacuum leaks in the air induction system especially between the MAF sensor and the throttle body and that the hose clamps on the air induction system are all tight.

      Jun 08, 2010 | 2001 Chevrolet Venture

      Not finding what you are looking for?
      2012 Mercedes-Benz Sprinter Logo

      Related Topics:

      133 people viewed this question

      Ask a Question

      Usually answered in minutes!

      Top Mercedes-Benz Experts

      Colin Stickland
      Colin Stickland

      Level 3 Expert

      22246 Answers

      yadayada
      yadayada

      Level 3 Expert

      76846 Answers

      Michael Contreras
      Michael Contreras

      Level 2 Expert

      166 Answers

      Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

      Answer questions

      Manuals & User Guides

      Loading...