Question about 2000 Ford Focus

Open Question

1.6 zmd camshaft setup

Camshaft timing marks alignment 1.6 zmd dohc engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

martin538
  • 117 Answers

SOURCE: dohc timing marks

This should help you.2724662.png

Posted on Apr 12, 2009

  • 234 Answers

SOURCE: What are the engine timing marks for a 2002 2.0

think thers 1 on the bottom pully line that up and the 2 top 1 s should be facing inwards if correct

Posted on Jun 05, 2009

honeymokey
  • 3113 Answers

SOURCE: there are no marks on the camshaft and crankshaft

A flat tool is needed for this to time the camshafts with the vale cover removed an the crankshaft at TDC.

Posted on Jun 13, 2009

  • 21 Answers

SOURCE: how to align cams on a 95 ford contour 2.0 dohc?

i have had good luck with the Haynes manuals available at almost all parts store chains.they are cheap and very easy to understand.plus they are great for future problems

Posted on Sep 06, 2009

motor1258
  • 6674 Answers

SOURCE: camshaft timing mark crankshaft timing mark

Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

Posted on Oct 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing belt


first ever post, with displacement . 93 Rodeo,
so can be looked up .

the belt (gates) comes with instructions, did you buy a cheap
china belt off fleabay? with none?

alldata.com shows
its a DOHC engine.
28 steps

first the warning. at step 13
Set the timing sprockets so that the crankshaft and camshaft sprocket timing marks align with the timing marks on the oil pump and front plate. When the timing marks are align, no pistons are at TDC for the compression stroke. Valve damage may result if the sprockets and belt are out of alignment.

there is a tensioner that as a locking pin,.do you know how to do that?

ill not answer how do it all, only the timing question.
here is the answer.
Ill answer not for removal but install.

install : step 1 and 2
  1. Align the groove on the crankshaft timing pulley with mark on the oil pump.
  2. Align the marks on the camshaft timing pulleys with the dots on the front plate.

photo 1 shows crank marked at 3pm cog wheel. and pump base.
photo 2 shows.



d8287f6b-372d-4688-85e1-6c00635efd23.jpg

there is more , but do log in at alldata.com and read all steps.
and win.

Jun 17, 2014 | 1993 Isuzu Rodeo

2 Answers

How do you fix the timing on the timing chain


I have a 2.2 single cam where are the marks on the gears

Aug 21, 2012 | 2004 Pontiac Sunfire

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

What is the position for the timing chain gears.


Timing Chain and Sprockets REMOVAL & INSTALLATION 2.3L and 2.4L Engines The following tools will be required to perform this procedure:
  • Camshaft sprocket timing alignment pins - J 36008 or equivalent
  • Camshaft sprocket wrench - J 39579 or equivalent
  1. Fig. 1: View of the DOHC engine "timed position'' - 2.3L and 2.4L engines 86883175.gif
    Fig. 2: View of the SOHC engine "timed position'' - 2.3L engine 86883176.gif
  2. Remove the timing chain guides. There are usually three.
  3. Raise and safely support the front of the vehicle.
  4. Make sure all of the slack is above the tensioner. Gently pry off timing chain tensioner spring retainer, then remove the spring. NOTE: On the 2.3L engine two styles of tensioners are used. Early production engines will have a spring post and late production ones will not. Both styles are identical in operation and are interchangeable.
  5. Remove the timing chain tensioner shoe retainer.
  6. Make sure all the slack in the timing chain is above the tensioner assembly; remove the chain tensioner shoe. The timing chain must be disengaged from the wear grooves in the tensioner shoe in order to remove the shoe. Slide a suitable small prybar under the timing chain while pulling shoe outward.
  7. If difficulty is encountered while removing chain tensioner shoe, proceed as follows:
    1. Lower the vehicle.
    2. Hold the intake camshaft sprocket with a camshaft sprocket wrench - J 39579 or equivalent holding tool and remove the sprocket bolt and washer.
    3. Remove the washer from the bolt and re-thread the bolt back into the camshaft by hand. The bolt provides a surface to push against.
    4. Remove intake camshaft sprocket using a 3-jaw puller in the 3 relief holes in the sprocket. NOTE: Do NOT try to pry the sprocket off the camshaft or damage to the sprocket or chain housing could occur.
  8. Unfasten the tensioner assembly attaching bolts, then remove the tensioner. CAUTION
    The tensioner piston is spring loaded and could fly out causing personal injury. Use care when removing.
  9. Matchmark the timing chain outer surface for reassembly purposes.
  10. If equipped, remove the chain housing to block stud, which is actually the timing chain tensioner shoe pivot.
  11. Remove the timing chain.
  12. Inspect the parts for wear, then replace if necessary. Some scoring of the timing chain shoe and guides is normal. Clean the old sealant off of the bolt with a wire brush. Clean the threaded hole in the camshaft with a round nylon bristle brush. To install: WARNING
    Failure to following installation procedures can result in severe engine damage.
  13. Install the intake camshaft sprocket onto the camshaft with the marked surface showing. Install the sprocket retaining bolt and washer. Use an adhesive compound 12345493 or equivalent on the bolt. Tighten the bolt to 52 ft. lbs. (70 Nm), while holding the sprocket with tool J-36013, J 39579 or equivalent, if removed.
  14. Install tool J 36800 or equivalent, through hole(s) in the camshaft sprocket(s) into the holes in the timing chain housing. This positions the camshafts for correct timing. Fig. 3: Placing the camshaft sprockets onto the marked surface of the camshaft 91063g30.gif
  15. If the camshafts are out of position and must be rotated more than 1?8 turn in order to install the alignment dowel pins:
    1. The crankshaft must be rotated 90┬░clockwise off of TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft COUNTERCLOCKWISE back to TDC. NOTE: Do NOT rotate the crankshaft clockwise to TDC, or valve and piston damage could occur. WARNING
      The side of the timing chain that was marked must be facing outward when installed.
  16. For DOHC engines only, install the timing chain over the exhaust camshaft sprocket, around the idler sprocket and around the crankshaft sprocket.
  17. Remove the alignment dowel pin from the intake (DOHC only) camshaft. Using dowel pin remover tool J 39579 or equivalent, rotate the intake (DOHC only) camshaft sprocket counterclockwise enough to slide the timing chain over the intake (DOHC only) camshaft sprocket. Release the camshaft sprocket wrench. The length of chain between the two camshaft sprockets will tighten. If properly timed, the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated. Fig. 4: Place the timing chain over the exhaust camshaft and around the idler sprocket and around the crankshaft sprocketDOHC engines 91063g31.gif
  18. Leave the alignment dowel pins installed.
  19. Raise and safely support the vehicle.
  20. With slack removed from chain between intake camshaft sprocket (camshaft sprocket for SOHC engines) and crankshaft sprocket, the timing marks on the crankshaft and the cylinder block should be aligned. If marks are not aligned, move the chain one tooth forward or rearward, remove the slack and recheck the marks.
  21. If equipped, tighten the chain housing to block stud. The stud is installed under the timing chain. Tighten to 19 ft. lbs. (26 Nm).
  22. For vehicles through 1991, reload timing chain tensioner assembly to its "zero'' position as follows:
    1. Assemble restraint cylinder, spring and nylon plug into plunger. Index slot in restraint cylinder with peg in plunger. While rotating the restraint cylinder clockwise, push the restraint cylinder into the plunger until it bottoms. Keep rotating the restraint cylinder clockwise but allow the spring to push it out of the plunger. The pin in the plunger will lock the restraint in the loaded position.
    2. Install tool J-36589 or equivalent, onto plunger assembly.
    3. Install plunger assembly into tensioner body with the long end toward the crankshaft when installed.
  23. For 1992-98 vehicles, reload timing chain tensioner assembly to its "zero'' position as follows:
    1. Form a keeper from a piece of heavy gauge wire. See the accompanying figure.
    2. Apply slight force on the tensioner blade to compress the plunger.
    3. Insert a small prybar into the reset access hole, then pry the racket pawl away from the ratchet teeth while forcing the plunger completely in the hole.
    4. Install the keeper between the access hole and the blade. Fig. 5: View of reloading the timing chain tensioner assembly to its "zero'' position - 1992-98 vehicles 86883177.gif
  24. Install the tensioner assembly to the chain housing. Recheck the plunger assembly installation. It is correctly installed when the long end is toward the crankshaft.
  25. Install and tighten timing chain tensioner bolts. Tighten to 89 inch lbs. (10 Nm).
  26. Install the tensioner shoe and tensioner shoe retainer. Remove the special tool J-36589, then squeeze the plunger assembly into the tensioner body to unload the plunger assembly.
  27. Lower vehicle enough to reach and remove the alignment dowel pins.
  28. Rotate crankshaft clockwise (normal rotation) two full rotations. Align the crankshaft keyway with the mark on the cylinder block, then reinstall the alignment dowel pins. The pins will slide in easily if the engine is timed correctly. WARNING
    If the engine is not correctly timed, severe engine damage could occur.
  29. Install the timing chain guides and, if equipped, the crankshaft oil slinger.
  30. Install the timing chain front cover. For details, please refer to the procedure located in this section.
  31. Connect the negative battery cable, then start the engine and check for oil leaks.

Oct 07, 2010 | 1998 Buick Skylark

1 Answer

Hi, I am looking for a timing belt diagram for a 1998 2.5ltr Subaru Outback or can you tell me which timing marks on the sprockets line up to the encasing.


Timing Belt Cover, Belt & Sprockets Removal & Installation 2.5L Engine To Remove:
  1. Remove the drive belts.
  2. Remove the A/C compressor drive belt tensioner. Timing belt & cover DOHC exploded view subaru-03-25-6470.gif

  3. Remove the crankshaft pulley.
  4. Remove the mounting bolts and left timing belt cover.
  5. Remove the mounting bolts and right timing belt cover.
  6. Remove the mounting bolts and front timing belt cover.
  7. Vehicles W/ M/T: Remove the timing belt guide.
  8. Ensure that the timing belt rotation arrows are still visible. If the marks are worn off, place new rotation marks on the belt. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  9. Turn the crankshaft using a breaker bar and special adapter socket on the crankshaft. Align the timing mark on the crankshaft sprocket (1), left intake sprocket (2), left exhaust sprocket (3), right intake sprocket (4) and right exhaust sprocket (5) with the notches in cylinder block and timing belt cover.
  10. Paint alignment marks on the timing belt at the crankshaft and camshaft sprockets timing marks. CAUTION
    Do not turn the camshaft sprockets with the timing belt removed. The valves heads will contact each other causing the valve stems to bend.
  11. Remove the lower right idler pulley.
  12. Remove the timing belt.
  13. Remove the upper right idler pulley.
  14. Remove the lower left (toothed) idler pulley.
  15. Remove the belt tensioner.
  16. Hold the sprocket and remove the left intake and exhaust camshafts.
  17. Hold the sprocket and remove the right intake and exhaust camshafts.
  18. Remove the crankshaft sprocket.
To Install:
  1. Install the crankshaft sprocket.
  2. Hold the sprocket and install the right intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  3. Hold the sprocket and install the left intake and exhaust camshafts with the mounting bolts. Tighten 58 ft-lb (78 Nm).
  4. Reset the automatic belt tensioner as follows:
    • Remove the mounting bolt and belt tensioner. NOTE: Do not exceed more than 2,205 lb. (9,807 N).
    • Place the belt tensioner on a press. Press the adjuster rod down gradually (using more than 3 minutes) 66- lb (165 N) or more until the adjuster rod is aligned with the stop pin hole in the cylinder.
    • Insert a 0.08 in (2 mm) diameter pin or hex wrench into the pin hole to lock the adjuster rod.
    • Install the automatic belt tension adjuster with the mounting bolt. Tighten 18 ft-lb (25 Nm).
  5. Install the lower left (toothed) idler pulley. Tighten 29 ft-lb (39 Nm).
  6. Install the upper right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm). Crankshaft sprocket and oil pump cover alignment marks 2.5L DOHC subaru-03-25-4890.gif

  7. Align the timing mark on the crankshaft sprocket with the mark on the oil pump cover. Timing belt alignment marks DOHC subaru-03-25-6472.gif

  8. Align the single timing mark on the right exhaust camshaft sprocket with the notch on the timing belt cover.
  9. When the single timing mark on the right exhaust camshaft sprocket is aligned with the notch on the timing belt cover, ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned.
  10. Align the single timing mark on the left exhaust camshaft sprocket with the notch on the timing belt cover by turning the sprocket counter clockwise (viewed from front of engine).
  11. Ensure that the double lines on the intake camshaft and exhaust camshaft sprockets are aligned when the single timing mark on the left exhaust camshaft sprocket is aligned with the notch on the timing belt cover. CAUTION
    • The camshafts can be rotated independently causing the valves heads to contact each other resulting in bent valve stems.
    • When the timing belt is removed the camshafts will turn to the lowest cam lobe position by the force of the valve springs. Before installing the timing belt the 4 camshafts are in the lowest lift position (valves closed).
    • When the camshafts are rotated to install the timing belts, # 2 intake and # 4 exhaust cam lobes of the left camshafts are held to push their corresponding valves down. In this position, these valves are held in the open position. Right camshafts are held so their cam lobes do not push the valves down.
    • The left camshafts must be rotated from the lowest lobe position to the position where the timing belt can be installed at the smallest possible angle in order to prevent intake and exhaust valve contact. Camshaft sprockets rotation subaru-03-25-6473.gif

    • Do not turn the camshafts in the direction shown in the illustration because the valves will open at the same time and contact each other.
    CAUTION
    If the timing belt alignment is off the mark buy more than 3 teeth, the valves and pistons may have contact.
    Timing belt alignment marks DOHC subaru-03-25-6472.gif

  12. Align the timing marks on the belt with the marks on the sprockets in the numerical order shown in the illustration.
  13. Install the lower right idler pulley with the mounting bolt. Tighten 29 ft-lb (39 Nm).
  14. Ensure that the timing mark alignment is correct and remove the tensioner stop pin.
  15. Vehicles W/ M/T: Install the timing belt guide and temporarily tighten the mounting bolts.
  16. Vehicles W/ M/T: Measure the clearance between the guide and timing belt. The clearance should measure 0.039 ┬▒ 0.020 in (1.0 ┬▒ 0.5 mm).
  17. Vehicles W/ M/T: Tighten the guide bolts 7.2 ft-lb (9.8 Nm).
  18. Install and secure the front timing belt cover with the mounting bolts.
  19. Install and secure the right timing belt cover with the mounting bolts.
  20. Install and secure the left timing belt cover with the mounting bolts.
  21. Install the crankshaft pulley.
  22. Install the A/C compressor drive belt tensioner.
  23. Install the drive belts.
prev.gif next.gif

Sep 30, 2010 | Subaru Outback Cars & Trucks

1 Answer

Timing belt broke,engine out of time,need to timing and install new belt how do i set timing.98 escort zx2 2.0 L


2.0L Engine SOHC ENGINE
  1. Remove the drive belt and timing cover.
  2. Raise the car and support it with safety stands.
  3. Remove the right-hand splash shield and the crankshaft pulley. Fig. 11: The timing marks on both the camshaft and crankshaft pulleys must be aligned like this before removing or installing the timing belt — 2.0L SOHC engines 90983g66.gif

  4. Align the timing marks as illustrated in the accompanying illustration.
  5. Refer to the accompanying illustration and remove the timing belt as follows:
    1. Loosen the timing belt tensioner bolt (1).
    2. Use an 8mm Allen wrench, and turn the tensioner (2) counterclockwise 1⁄4 turn.
    3. Insert a 1⁄8 inch drill bit in the hole (3) to lock the belt tensioner in place.
    4. Remove the timing belt (4). Fig. 12: Remove the timing belt by following these 4 numbered steps (refer to the text for an explanation) — 2.0L SOHC engine 90983g67.gif

    5. Inspect the belt for damage and signs of oil leakage. To install: NOTE: Install the timing belt over the sprocket in a counterclockwise direction starting at the crankshaft. Keep the belt span between the crankshaft and camshaft tight when installing the belt over the camshaft.
  6. Install the timing belt and remove the drill bit.
  7. Tighten the tensioner bolt to 15–22 ft. lbs. (20–30 Nm).
  8. Rotate the engine two complete revolutions and make sure the timing marks are aligned.
  9. Install the timing belt cover and crankshaft pulley.
  10. Install the right-hand splash shield and the drive belt.
  11. Start the car and check for proper operation.
DOHC ENGINE NOTE: A camshaft alignment timing tool (No. T94P-6256-CH or equivalent) and a crankshaft Top Dead Center (TDC) timing peg tool (No. T97P-6000-A or equivalent) are required for this procedure. NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block. Refer to the accompanying illustration. Fig. 13: A camshaft alignment timing tool . . . 90983g68.gif
Fig. 14: . . . and a crankshaft TDC timing peg tool are required when removing and installing the timing belt 90983g69.gif
  1. Remove the spark plugs.
  2. Rotate the crankshaft to TDC.
  3. Locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg. Fig. 15: Remove the plug bolt by the Crankshaft Position (CKP) sensor and install the TDC timing peg 90983g70.gif

  4. Raise the car and support it with safety stands.
  5. Unfasten the splash shields bolts and remove the shield.
  6. Lower the car and remove the water pump pulley.
  7. Remove the valve cover and the timing belt covers.
  8. Align the camshafts and install the camshaft alignment tool on the back of the camshafts as illustrated. Fig. 16: Align the camshafts and install the alignment tool 90983g76.gif
    WARNING
    If the camshaft belt is being reused, mark the direction of the camshaft belt to the rotation of the camshaft prior to removal, or premature wear and belt failure could occur.
  9. Loosen the tensioner pulley bolt and relieve the tension on the belt by disconnecting the tensioner tab from the timing cover back plate.
  10. Slide the belt off the sprockets.
  11. Inspect the belt for wear and replace as necessary. Fig. 17: Timing belt routing — 2.0L DOHC engine 90983g71.gif
    To install:
  12. If, for any reason, the engine was disturbed, the camshafts moved or the sprockets replaced, perform the following procedure: NOTE: Make sure the correct notch in the pulley is indexed to the lower cylinder block.
    1. Position the crankshaft just prior to Top Dead Center (TDC).
    2. If not already done, locate and remove the plug bolt by the Crankshaft Position (CKP) sensor (refer to the illustration) and install the TDC timing peg.
    3. Rotate the crankshaft clockwise against the TDC peg. NOTE: Installation of the alignment tool into the exhaust camshaft may require the camshafts to be rotated clockwise.
    4. Install the camshaft alignment tool on the back of the camshafts.
    5. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
    6. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
    7. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool.
    8. Remove the TDC peg tool and install the plug bolt.
    9. Install the timing and valve covers.
    10. Install the water pump pulley and the splash shield.
    11. Install the spark plugs. If the engine or the camshaft were not disturbed in any way, or the sprockets were not removed, perform the following procedure:
  13. Install the timing belt and engage the timing belt tensioner tab into the upper timing cover backplate. Fig. 18: Engage the timing belt tensioner tab into the upper timing cover backplate . . . 90983g72.gif
    Fig. 19: . . . then use a 6mm Allen wrench to adjust the tensioner until the index marks are aligned 90983g73.gif
    Fig. 20: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt (arrow) — 2.0L DOHC engine 90983g75.gif
    NOTE: A 3⁄8 inch drive, 10mm, 2 inch torque adapter offset is required to tighten the tensioner bolt.
  14. Using a 6mm Allen wrench, adjust the tensioner until the index marks are aligned and tighten the bolt to 17–20 ft. lbs. (22–28 Nm).
  15. Rotate the crankshaft clockwise against the TDC alignment peg, then remove the camshaft alignment tool. Fig. 21: Rotate the crankshaft clockwise against the TDC alignment peg 90983g74.gif

  16. Remove the TDC peg tool and install the plug bolt.
  17. Install the timing and valve covers.
  18. Install the water pump pulley and the splash shield.
  19. Install the spark plugs.
prev.gif next.gif

Aug 26, 2010 | Ford E-Series Cars & Trucks

1 Answer

Timing marks 2000 ford escort


Hi!!

Here are 3 diagrams that correspond to the 3 engines types available for your vehicle.


0996b43f80208cbd.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Be sure that the intake and exhaust camshaft timing marks align so that they face each other-Ford 2.0L (VIN A) engines

2.0L (VIN P) Engines


0996b43f8022f40e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Align the timing marks before removing or installing the timing belt-2.0L (VIN P) SOHC engines



0996b43f80208cbe.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft alignment position-Ford 2.0L DOHC Zetec engines

In case the diagrams don't show, click the following link http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?chapterTitle=Engine+Mechanical+Components&partName=Engine+Mechanical&pageId=0996b43f802e7310&subChapterTitle=Timing+Belt&partId=0996b43f802e7275#hd1-1-3

Don't forget to rate this answer, GOOD LUCK

Apr 17, 2010 | 2000 Ford Escort

1 Answer

Need to find timing marks for camshaft on 2002 hyundai sonota dohc


hi from uk the camshaft marks at TDC should be both cams at 12o/clock positions in line with pointer on on rear of cams on engine? the crankshaft at TDC marks lined up at approx 11 o/clock thebalance shaft/cog must also aligne with marks on cog and engine these are at 9 o/clock position ? the oil pump cog also is market to aligne with engine mark on engine at approx 11 o/clock all above is prior to fitting new belt+tensioner hope this helps ? best wishes from n/west uk

Nov 08, 2009 | Hyundai Sonata Cars & Trucks

2 Answers

2000 isuzu trooper 3.2 v-6 dohc camshaft timing marks pulled camshafts to do valve job and need to align marks on drive gear and cams


It's more to it than aligning the marks since the cam pulleys turn about three times or more to one turn of the camshaft on this engine. You need to find someone that is experienced on this vehicle.

May 12, 2009 | 2000 Isuzu Trooper

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...