Question about 2007 Nissan 1400 Bakkie

Open Question

Location of engine number nissan 1400 - 2007 Nissan 1400 Bakkie

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi can anyone help. Can the engine cross member be taken off from the vehicle on a Nissan 1400 van. Many Thanks


Yes, you will need a special tool to support the engine and transmission if you are planning on leaving them in the vehicle when you remove the cross member.

Jun 26, 2017 | Nissan Cars & Trucks

1 Answer

1996 nissan 1400 champ shakes the engine on idling and cuts off.secondly its not accelarating and making some sqicking noise in the engine.


Have you checked for any vacuum leaks ? Have you done a complete and proper tune up ? Any codes in ECM or an engine light on ?

Dec 07, 2016 | Nissan Cars & Trucks

1 Answer

How do I set tappets on Nissan 1400


With a special tool called a feeler gauge remove the valve covers and one by one bring the cylinders up to top dead center (both valves are fully closed at this point) adjust to factory spec. All adjustments are done cold. If engine is very high miles reduce the clearances in specs by slight amount (.002") to the tight side to account for wear in the valve train parts.

Nov 16, 2015 | 2006 Nissan 1400 Bakkie

1 Answer

Location of nissan 1400 dashboard light. dashboard does not light and I need to fix the problem


Often necessary to remove the instrument cluster to access these bulbs, but have you checked the fuses?

Dec 12, 2014 | 2007 Nissan 1400 Bakkie

2 Answers

Nissan 1400 pick up is not starting how do you set the points for igition


Check for spark to the spark plugs during the no start period. If you do not have spark the crank sensor in the distributor is a common failure in these.

Oct 20, 2013 | 2006 Nissan 1400 Bakkie

1 Answer

How do I set the timming on a 1400 Nissan sentra 1998 model


This is for a 1998 nissan sentra 1.4 engine, start engine and allow to reach operating temp.then turn engine off and disconnect throtle postion sensor connector.

With tps sensor disconnected start engine and increase idle to 2000 rpm three times then release and allow it to idle.

now check timing, timing should be at 6-10 degrees BTDC. adjust as needed then turn key off and reconnect tps .
Good day.7_15_2012_4_06_52_pm.gif7_15_2012_4_07_06_pm.gif

Jul 15, 2012 | Nissan Sentra Cars & Trucks

1 Answer

I recently changed the sparks plugs on my 2007 Nissan Versa and now I am getting random idle problems while my car is in park. The car will idle from 1400 rpms them all of a sudden jump up to 2100 rpms and...


If your check engine light is on have it scanned for fault codes. Also check to make sure you don't have a vacuum leak, you could of pulled a hose loose accidently when you changed your plugs.
Signals from the oxygen sensor, and/or a bad throttle position will also cause engine surge.
Good luck, i hope this helps.

Jun 28, 2011 | 2007 Nissan Versa 1.8 Sl Hatchback

Not finding what you are looking for?
2007 Nissan 1400 Bakkie Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...