Question about 2011 Buick Lucerne

1 Answer

REar compartment light stays on 1/2 hour - 2011 Buick Lucerne

Posted by on

  • Bob Granger
    Bob Granger Apr 16, 2014

    I just found out (garage) just tap the light. Too easy!!

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 37 Answers

Compartment switch not working properly

Posted on Apr 15, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do I have to change my license plate assembly since my bulb is out on my 2004 Cadillac cts 3.6l v6


no just change the bulb .

Open the rear compartment.
Remove the rear compartment lid applique. Refer to Rear Compartment Lid Applique Replacement in Body Rear End

1.Remove the rear compartment lid trim. Refer to Rear Compartment Lid Inner Panel Trim Replacement .
Remove the fastener securing the rear compartment pull down strap to the rear compartment lid.
Remove the rear compartment pull down stap.
Remove the fastener securing the rear compartment release handle escutcheon.
Remove the rear compartment release handle escutcheon.
Remove the push-in retainers securing the rear compartment lid trim to the rear compartment lid.
Remove the rear compartment lid trim from the compartment lid.

Disconnect the rear compartment lid applique electrical connector (4).
Remove the fasteners that retain the rear compartment lid applique (1) to the rear compartment lid (2).
Remove the rear compartment lid applique (1) from the rear compartment lid (2).
Remove the rear compartment lid applique electrical harness pass through (3) from the rear compartment lid (2).

Remove the license lamp socket from the rear compartment lid applique by turning it counter clockwise.
Remove the license lamp bulb from the socket if replacing.
Remove the license lamp from the rear compartment lid applique by lifting the retaining tabs and sliding the lamp away from the applique.

Jan 20, 2017 | 2004 Cadillac CTS Sedan

2 Answers

Locked out of trunk 2000 cadillac eldorado release button not working i removed lock on trunk still cant get in trunk


Pressing the rear compartment lid release switch provides an input signal to the instrument cluster. The instrument cluster sends a Class 2 serial data message to the body control module (PZM). The PZM grounds connector C6 of the rear compartment lid release solenoid through CKT 1344 (LT BLU) if the following conditions are present:
?€¢
The transaxle is in the PARK position.


?€¢
The valet lockout switch is closed.

Power is supplied through the following components to the now-grounded CKT 1344 (LT BLU):
?€¢
The RADIO/PHONE fuse


?€¢
CKT 40 (ORN)


?€¢
The coil of the rear compartment lid release relay
The relay coil energizes and closes the relay contacts.
Power is supplied from the CONVENIENCE fuse through the following components:
?€¢
CKT 2040 (ORN)


?€¢
The now-closed relay contacts


?€¢
CKT 56 (BLK/WHT)


?€¢
The rear compartment lid release solenoid
The solenoid energizes and the rear compartment lid latch assembly releases the rear compartment lid.

1

Did you perform the rear compartment lid release system check?
--
--
Go to Rear Compartment Lid Release System Check

2

  1. Place the transaxle in the PARK position.
  2. Turn the valet switch OFF.
  3. Connect the scan tool to the data link connector (DLC).
  4. Turn the valet lockout OFF.
  5. Press the rear compartment release switch.
Does the body control module (PZM) command the rear compartment lid release ON?
--
Go to Step 3
Go to Step 7

3

  1. Disconnect the rear compartment lid release relay.
  2. Connect a test lamp between terminal D4 and ground, and terminal D6 to ground.
Does the test lamp light at both terminals?
--
Go to Step 4
Go to Step 14
  1. Connect the test lamp between terminal D4 and terminal C6.
  2. Press the rear compartment lid release switch.
Does the test lamp light?
--
Go to Step 5
Go to Step 15

5

Connect a fused jumper between terminal D6 and terminal C4.
Does the rear compartment lid open?
--
Go to Step 6
Go to Step 16

6

Replace the rear compartment lid release relay.
Does the rear compartment lid release operate properly?
--
Go to Rear Compartment Lid Release System Check
Go to Step 7
If you don't know what your dealing with there is no way you can fix it . I suggest you take it to a qualified ASE certified repair shop or the dealer !

Aug 24, 2015 | Cadillac Cars & Trucks

1 Answer

Who do you get in to change the back up light


Welcome to FIxYa.com


BACKUP LAMP REPLACEMENT

REMOVAL PROCEDURE

1. Open the rear compartment lid.

2. Remove the rear compartment lid trim.

3. Pull back on rear compartment trim panel.

4. Disconnect the backup lamp connector (5) from the rear compartment lid wiring

harness.

5. Press the grommet (3) out of the rear compartment lid.

6. Remove the fasteners (4) securing the backup lamp (1) to the rear compartment lid

(2).

7. Remove the backup lamp (1) from the rear compartment lid (2).

INSTALLATION PROCEDURE

1magJ

1. Route the backup lamp connector (5) and the grommet (3) through the rear

compartment lid Q).

2. Install the backup lamp (1) to the rear compartment lid(2).

3. Install the fasteners (1) in order to secure the backup lamp (I) to the rear

compartment lid(2).

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten

Tighten the fasteners to 4.5 N.m (40 lb in).

4. Verify that the grommet (3) is filly seated in the rear compartment lid (2).

5. Connect the back-up lamp connector (5) to the rear compartment lid wiring harness.

6. Install the rear compartment lid trim.

7. Close the rear compartment lid.



leedavidian_169.jpg


Thank you for using FixYa.com

Regards, Lee Davidian

Dec 23, 2010 | 2003 Cadillac Seville

1 Answer

How do you replace the tail light bulbs on a 2006 Pontiac Vibe


Tail Lamp: Service and Repair
TAIL LAMP REPLACEMENT
REMOVAL PROCEDURE
1. Open the rear compartment lid.
2. Remove the rear compartment trim panel (4).
3. Disconnect the tail lamp electrical connectors.
4. Remove the following components from the vehicle:
- The 3 nuts (3)
- The tail lamp (7)
5. Remove the following from the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
6. Remove the following from the lamp sockets, if necessary:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
INSTALLATION PROCEDURE
1. Install the following to the lamp sockets, if removed:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
2. Install the following to the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
3. Install the tail lamp (7) to the vehicle. Secure the tail lamp (7) with the 3 nuts (3).
NOTE: Refer to Fastener Notice in Service Precautions.
Tighten the tail lamp nuts to 10 N.m (89 lb in).
4. Connect the tail lamp electrical connectors.
5. Install the rear compartment trim panel (4) to the vehicle.
6. Close the rear compartment lid.

Oct 30, 2009 | 2003 Pontiac Vibe

1 Answer

97 Altima dashboard brake light stays on


Check your brake fluid level in the engine compartment. Its located on the rear RH side of the engine compartment, its a white/clear resevoir connecting to a large black circular object. If the fluid is low, fill to proper level, also I would recommend having your brake system checked as there may be a leak. If the fluid is fine and at the proper level, you may have a damaged/broken brake fluid level sensor or damaged/broken Emergency brake switch. Hopefully this helps....please rate thanks!!

Aug 09, 2009 | 1997 Nissan.5 Altima

1 Answer

Brak Bleeding


on most vehicules you have to unplug the battery for at least 1 hour to reset the computer after a light has come on....

Apr 29, 2009 | 1988 Mazda B2200

1 Answer

How do I replace a taillight lens on a 1991 Geo Storm?


Rear Turn Signal, Brake and Parking Lights


STORM COUPE
  1. Disconnect the negative battery cable.
  2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
  3. Remove the ten plastic retaining clips from the rear end trim panel.
  4. Disconnect the luggage compartment lamp electrical connector.
  5. Remove the luggage compartment trim panel and the rear end trim panel.
  6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm
84256028.gif
  1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
  2. Disconnect the rear combination lamp electrical connector.
  3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
  4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
  5. Connect the rear combination lamp electrical connector.
  6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
  7. Connect the rear combination lamp assembly electrical connector.
  8. Install the rear end trim panel and the luggage compartment trim panel.
  9. Connect the luggage compartment lamp electrical connector.
  10. Install the ten plastic retaining clips to the rear end trim panel.
  11. Install the spare tire cover panel and the luggage compartment floor carpet.
  12. Connect the negative battery cable.

Mar 21, 2009 | 1991 Geo Storm

3 Answers

Have a 2003 Chevy Impala. Check engine light remains on. Scan showed O2 sensor. Could it be a vaccum leak?


Bank 1 is the rear O2 sensor, but experience says to change both. The front one is right behind the engine in the middle of the engine compartment. The rear O2 sensor is on the top of the exhaust pipe, just behind the catalytic converter. But the same code that shows it is the O2 sensor (which is P0420), is the same code for the catalytic converter, or a vacuum leak. Make sure if you do change the catalytic converter, ensure that the new one is OBD-2 compliant. And the vacuum leak could possibly come from the manifold gasket. Let me know what the problem was!

Mar 11, 2009 | 2003 Chevrolet Impala

2 Answers

License plate bulb on 1997 Cadillac deville


this is straight out of the book ok



  1. Open the rear compartment lid.
  2. Remove the rear compartment lid trim.
  3. Pull back on the rear compartment trim panel.
  4. Unplug the lamp connector from the rear compartment lid wiring harness.
  5. Press the grommet out of the rear compartment lid.
  6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
  7. Remove the bulb.

Mar 07, 2009 | 1997 Cadillac DeVille

1 Answer

Inside lights stay on for about 1 hour after shut off


try spraying some WD40 into all the latches including the hatch. the switches have a problem with sticking

Jan 17, 2009 | 1997 Mercury Mountaineer

Not finding what you are looking for?
2011 Buick Lucerne Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...