Question about 2001 Lincoln Town Car

1 Answer

Air motor stop running check it the plug has no power

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 1,171 Answers

Replace the bad air pump.It's part of the emmissions control system and a must have.

Posted on Apr 14, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i check fluid for convertable top


"How do I get the air out of my hydraulic system"?
  • Remove the reservoir plug on the motor pump. Leave the plug out and do not put back until you have finished.
  • Fill the reservoir 3/4 full with fluid (to the bottom of filler plug hole). Put a rag under the hole to catch overflow that will occur as system fills.
  • Run the pump for 15-20 seconds. Stop. Check your fluid level and refill to bottom of filler hole. Continue running the motor in the same direction for an additional 15-20 seconds. When the top gets to the end of cycle, check your fluid level, fill to bottom of filler hole, and run the motor in the opposite direction.
  • You are literally running the top all the way up and down sereral times. Checking the fluid level as you go and fill as required, leaving reservoir 25% empty.
  • When you are no longer able to add fluid, put the top in the down position. Check the fluid level one last time, should be to bottom of filler hole. Put the plug into reservoir.
    "How do I get the air out of my hydraulic system"?
  • Remove the reservoir plug on the motor pump. Leave the plug out and do not put back until you have finished.
  • Fill the reservoir 3/4 full with fluid (to the bottom of filler plug hole). Put a rag under the hole to catch overflow that will occur as system fills.
  • Run the pump for 15-20 seconds. Stop. Check your fluid level and refill to bottom of filler hole. Continue running the motor in the same direction for an additional 15-20 seconds. When the top gets to the end of cycle, check your fluid level, fill to bottom of filler hole, and run the motor in the opposite direction.
  • You are literally running the top all the way up and down sereral times. Checking the fluid level as you go and fill as required, leaving reservoir 25% empty.
  • When you are no longer able to add fluid, put the top in the down position. Check the fluid level one last time, should be to bottom of filler hole. Put the plug into reservoir.
  • Apr 01, 2012 | 2004 Ford Mustang

    1 Answer

    Ac stopped blowing any type of air


    things to check; blower fuse, blower relay, fan control, blower motor resistor, blower motor.

    You can check for power at the plug for the blower motor and back track from there. If you have power at the plug then you need to replace the blower. A cheap 12V probe tester will tell you everything you need to know. Let me know your findings and we can narrow down the possibilities

    Sep 03, 2010 | Chevrolet 1500 Cars & Trucks

    2 Answers

    98 Camero overheats when driving slow or stop, ok


    You need to get the cooling fan checked,it may need a temperature sensor,fan relay or the fan motor may be burnt out.You can check the fan by running your own power and ground to the plug that comes out of the fan motor,unplug it and put the ground to the black wire and positive power to the other one,if it works then the next step would be to check the fan relay.The most common problem if the fan doesn't work but can be made to work with jumper wires is the temperature sensor,you can check it by unplugging it and jumping the wires in the plug.If the rad fans work then you are down to either the water pump or a plugged radiator,a rad shop should be able to narrow it down for you.

    Jul 14, 2010 | 1998 Chevrolet Camaro

    1 Answer

    Fan motor for a/c and heat not blowing air can you help


    The blower motor runs on several settings, but if the motor will run only on the HIGH setting, then the Motor resistor is bad.

    If it will not run at all, first check the blower fuse (Location in your owners manual. If that is good, check to see if power is reaching the motor by setting the inside switch on HIGH (With key ON). Then, using a multimeter or test light at the plug on the motor, check for 12 volts. If you have power there, then the motor is most likely bad or jammed, or the plug connection is corroded. The motor should be mounted in the engine compartment on the drivers side firewall. It will look like a soup can mounted on a flat disk.

    If there is no power, then the blower motor relay is the likely culprit. They are only about $7and easy to replace. Your owners manual should point out the location.

    Hope this helps.

    Jul 04, 2010 | 1998 Ford Escort

    1 Answer

    Car a/c heat blower stopped no warning


    Check for a blown heater motor supply fuse,
    Check operation of heater motor control relay,
    Check operation of fan speed control switch,
    Check heater motor speed control resistor pack (usually located in the heater ducting - in the air flow),
    Check the heater motor runs if power directly applied to the motor- if not motor may be faulty.

    Aug 26, 2009 | 2003 Dodge Neon

    1 Answer

    Air conditioning stopped running, no power


    If the air conditioner has stopped, it can be three things. The clutch, the relay, or the motor. Look around in relay centers to see where the relay and fuse are for the conditioner. You can check with a multi-meter, or ohmmeter to determine if relay and fuse are good. You can also use the same tester to determine if there is power in the wiring going to the air conditioner motor.

    Jun 15, 2009 | 1995 Lexus ES 300

    1 Answer

    Engine checklamp is flashing constantly and the motor stop running.


    first chek your sparking plugs your engine maybe working on with one or more cylinders is off . then check your distributar

    May 31, 2009 | 1994 Toyota Corolla

    2 Answers

    Air stopped blowing on ac/heater


    Check your fuses.If you have a test light, unplug the blower motor, start the car, turn the fan on, if you have power to the blower plug, the blower motor is bad. If no power, if it's not a fuse, check the blower motor resistor. Should be mounted right next to the blower motor. It is inserted into the evaporator box

    Nov 22, 2008 | 2002 Dodge Durango

    3 Answers

    Loss of power


    were is distributor cap on 00 kia sportage

    Aug 17, 2008 | 2000 Kia Sportage

    Not finding what you are looking for?
    2001 Lincoln Town Car Logo

    Related Topics:

    12 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Lincoln Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    fordexpert

    Level 3 Expert

    5520 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you a Lincoln Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...