Question about 1994 Toyota T100

1 Answer

I have a 1994 toyaota T100 4x4 that i've just replaced the metal brake lines on. I've bled the brakes, and have good pedal pressure until I statrt the truck, then it gets mushy again. Any ideas?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 22 Answers

Fluid could be low still. When it puts on pressure, there isn't enough fluid for the higher pressure it build it up too. So, check your fluid level after a turn on/off.

Posted on Apr 14, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 881 Answers

SOURCE: replaced both rear metal brake pipes cant get good brake pedal

Try jacking up car and put on stands as high as poss as you could have air returning when the pedal is returned ,so jack up car pump pedal 4 times fast and hold down bleed l/h/s/first ,do 2 times then the r/h/side and then push down pedal clamp rubber flex hose over back axlewith small G clamp if pedal good do same to FRONT

Posted on Sep 22, 2009

  • 136 Answers

SOURCE: I have no front brakes on my 88 Toyota. I've bled

You may have to install brake cylinder kits on the front wheels. The kits come with all you need to replace them. Or it could also be the main cylinder that's leaking.

Posted on Nov 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have replaced my brake pads I've bleed my lines several times. The brakes work fine until I hold the brake pedal down, thats when it slowly goes down to the floor in a few seconds and the brak


sounds like the brake master cylinder seals are worn buy a master cylinder kit and get a mechanic to repair it it is a lot cheaper than replacing the whole unit

Feb 27, 2013 | 1995 Honda Passport

1 Answer

No pressure on brake pedal 95 suburban 2500 4x4 7.4L


try bleeding your ABS block first, if that doesn not work could need a master or proportioning vavle. Some scan tools are capable of bleeding the ABS system on some vehicles, and some you have to bleed manually.

Apr 07, 2012 | 1995 Chevrolet Suburban

1 Answer

No pedal 94 saturn


ajust rear brakes untill there is only 4 click on the parking brake

Mar 04, 2012 | 1994 Saturn Sc

1 Answer

2003 chevy silverado 4wd -- front brake line broke repaced and bled brakes now i have no pedal pressure thanks


If there's no pedal pressure, you've still got air in the brake pipes or you've got an open fluid circuit. Look for leaks, if none they need bleeding again.

Sep 01, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

No brake fluid to the rear wheel cylinders


You'll need to start bleeding the brake system at the Master cylinder to determine where the problem lies.

The lines coming out of the master cylinder will need to be loosened & bled there, initially you can just do the back ones to identify the problem, but once fixed, the system will have to be bled from the Master cylinder first, then the farthest wheel from it, then next farthest, then next, until you do the drivers wheel last.

This method of bleeding the brakes prevents air from crossing from one line to another, causing air to be left in the system.

Back to bleeding the rear brakes first: As someone pumps up the brake pressure, making sure the resivoir stays full, with the cap on between bleeding, and have the person pressing the pedal to do these thngs.
1. Always move the pedal slowly, pressing and releasing.
2. Never release the pressure on the pedal after bleeding a brake, until the line is tightened, then release slowly to prevent air from getting into the fluid.

You should of course get fluid at the master cylinder when you bleed it (or just replace it), then you'll need to bleed the line at the right rear wheel (first) a few times to get fluid if it's been leaking, then the left rear wheel. If you get pressure but no fluid to the rear and the master cyliinder did have pressure released when you bled it, there is either a restriction in the line itself, or the porportioning valve could be damaged. (unusual for the valve to go bad actually, inspect lines for damage such as being pinched if you're getting pressure but no fluid.

Final test if it hasn't been resolved-remove lines at porportioning valve & make sure fluid is leaving/entering there as it should. If you find it defective, a good replacement can come from a salvage yard, or you can buy them new.

Brake fluid on the floorboard under the dash near the brake pedal=bad Master Cylinder.

good luck

Feb 21, 2010 | 1996 GMC Jimmy

3 Answers

Replaced both rear metal brake pipes cant get good brake pedal back.i have pressure bled system and now replaced master cylinder still spongy pedal???


there is air there somewhere. try manual bleeding the brakes. do the farthest wheel first. if they are calipers all the way around, when you bleed them tap them gently to remove any air that can still be inside the chambers.

robert

Sep 22, 2009 | Toyota Land Cruiser Cars & Trucks

Not finding what you are looking for?
1994 Toyota T100 Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...