Question about 1999 Toyota Camry

1 Answer

I replaced cam sensor on my 2004 jeep grand cherokee had oreilly's to clear the code and after driving about 100 miles my check engine light came back on now its coming back as the cam sensor again after having it checked

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 954 Answers

Please check the following:
- Valve timing
- Camshaft Position Sensor.
- Wiring and connectors.
- Camshaft timing gear assembly
- ECM

Posted on Apr 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: The check engine light keeps coming on for a 1998 Toyota Avalon.

Did you buy the universal replacement sensor where you use the plug off of the old sensor and the splice kit? If so, that is most likely the issue. Had the same problem on a 2003 Avalon. Bought the ones with the plug and codes cleared. ps. Check Amazon.com, lots less expensive.

Posted on Jul 14, 2009

seanpwright
  • 2030 Answers

SOURCE: how do I find out if my ecu is bad. I keep getting

Make sure the check engine light was cleared after you replaced the o2 sensor....if the codes were not cleared then it will come on forever even if thetre is no problem

Posted on Nov 13, 2009

  • 318 Answers

SOURCE: i have a toyota rav4 2003 management light came on

The upper sensors are air fuel sensors and the lower ones are o2 sensors. you cant mix these up. Assuming you did everything right and still coding then either the new sensor b1s2 is bad or the wirng(power and ground need to be checked. A scan tool can be used to look at the performance of the sensors too. Sometimes the codes just point to the area of the problem and changing the part isn't the answer.

Posted on Nov 15, 2009

  • 1 Answer

SOURCE: VSC Trac off/ VSC Trac

how do I determine which oxygen sensor is bad on my 2003 forerunner ? the check engine light is on and also the vsc trac

Posted on Apr 02, 2011

SOURCE: Toyota avensis fault code p0016 and p0016 codes

Crank/cam misaligned timing can be due to a slack timing belt jumping a tooth on a cog. Check that the belt is tight and that the timing marks on belt align with the cam and crank pulley timing marks.

Posted on May 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 grand cherokee had engine replaced. new engine did not have oil sensor attached. display always shows the sensor is bad and to check the oil. i have attempted 2x to go on long highway trips and between...


You can defeat the oil level sensor by shorting the connector. Use a thick paper clip or other wire shaped in a "U" to connect the terminals in the plug. For the other problem, we will need trouble codes. Is the engine light on?

Oct 04, 2010 | 1993 Jeep Grand Cherokee

1 Answer

Check engine light on,1997 Jeep Grand Cherokee,4.0 six cylinder.code 1757.cleared code,comes back on after a few minutes of driving. Trans is sluggish,when pulling out,after a complete stop.


I just had those similar symptoms with my 97 grand cherokee a week ago and my crankshaft position sensor had to be replaced...hope this helps.

Jan 23, 2010 | 1997 Jeep Grand Cherokee

1 Answer

2004 Jeep Grand Cherokee. Keeps stalling, engine


P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Oct 25, 2009 | 2004 Jeep Grand Cherokee

3 Answers

1999 grand cherokee laredo 4.0 and auto trans wont downshift


call the jeep dealer with v.i.n. number so you can get the right speed sensor and just install in the rear of your transmission. will only take about 10 min. to change

Jul 09, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Jeep Grand Cherokee Power Loss


a bad cam sensor will cause vehicle to shut off while driving, and cause a hard time starting. but this usually sets a trouble code p0340. scan vehicle to see if any codes come up. after it is fixed, erase codes with a obd2 scanner. if you do not have one, you can go to any auto parts store and they will erase codes for free.

May 02, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Engine light comes on 2003 Jeep grand cherokee laredo


Check the Fuel Pump Relay, it may be malfunctioning and need replaced. Also, in some vechicles, if the batter is disconnected and reconnected, the service engine light will come on from time to time, going off and on simultaneously. Have a diagnostics done to see if any codes show up. If no codes appear, then have them all cleared and drive for another 200 miles. Sometimes the computer will need to be cleared a couple times before the light will stay off. Make sure that all fuses and relays are good, and securey in place. Check all factory installed lights to make sure they are good, and securly in place as well.

Mar 31, 2009 | 2003 Jeep Grand Cherokee

2 Answers

2002 Jeep Grand Cherokee Lardo misfiring


You say you changed the cam sensor. A1391 code is a crank sensor on the top of the trans. bell housing.

Feb 22, 2009 | 2002 Jeep Grand Cherokee

2 Answers

Enging light on


crank shaft sensor or cam sensor

Aug 07, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Toyota Camry Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...