Question about 2003 Ford Taurus

1 Answer

On installing a tension pully

Need specs on installing

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 200 questions.

  • Expert
  • 279 Answers has a lot of info about replacing the belts and tension pulleys.

Posted on Jan 02, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I get a diagram for the serpinetine belt on a 2005 Chevy express 3500 van

There is a spring loaded tension pully that needs to be depressed. I believe is has a 1/2 inch square socket female end on the front of tension pully that you can use a 18" or 20" breaker-bar to get leverage to reduce the tension. Reduce the tension remove belt and just reverse the process to install new belt.

Jan 26, 2015 | 2005 Chevrolet Express

1 Answer

Need the spec on installing a tension pully for a 2003 ford taurus

Not sure what spec your looking for. I replaced the tensioner pully on my F-150 302 last year though. And basically the bolt is left hand thread and turning the bolt gives the slack in belt needed to take belt off, and put back on. Hope this helps.

Apr 14, 2014 | 2003 Ford Taurus

1 Answer

I recently installed a tension pully on my 1999 ford f150 and installed a new serpatine belt. how come the new pully rubs on the block?

Was there a small spacer on the idler arm when you pulled the old pulley? You may be able to resolve this with a small washer behind the pulley. Just make sure you get one that fits well on the shoulder bolt and does not extend out beyond the inner bearing ring. Kind of sounds like the pulley is out of spec though.

Feb 05, 2013 | Cars & Trucks

2 Answers

How to adjust fan belt on izusu bighorn 3.1d

Find the tensioner. Tensioner is a pully to adjust the tension of the belt. Mostly the Alternator is the tensioner pully. Check it. ok

Mar 10, 2010 | 1996 Isuzu Trooper

1 Answer

Drive belt installation, need to get belt over top alternator pully, do I loosen one of the pulleys to accomplish this ?

there is a tensioner as you face the engine on the left side, install the belt around the pulleys using the underhood belt routing. using a 3/8 ratchet pull the tensioner and then put the belt on thealternaor pully.

Aug 16, 2009 | 1999 Lincoln Town Car

1 Answer

Where do I loosen my belt that is runs A/C on 2000 Toyota Sienna?

One of those "wheels" or TENSIONER PULLYS on your vehicle is the tensioner for the a/c compressor. You will need to look at it and see if there is an adjustment bolt behind pully. If there is, loosen center pully nut, then run adjustment bolt out to slack out the belt. Replace belt and reverse prosedure. DO NOT OVERTIGHTEN BELT,as you can damage pullys and or belt. Tighten to factory specs. Rule of thumb is pulling the belt out and check for slack. No more/less than one inch slack.

Jul 23, 2009 | 2000 Toyota Sienna

2 Answers

How do you adjust tension for drive belt

first you need to figure out if you have an automatic tensioner or an adjustable one. so look at the pullies which ones are not accesories (ie not an alternator pully, power steering.) some pullies will just be on there own not driving anything. is this pully connected to something like this O>o <--this end is the pully.
pully mounting bolt ^ ^arm with hole for rachet
or does it look like the pully is attached to a threaded pole.

the auto adjuster need a rachet to pull back on it (because it's spring loaded) while you install the new belt.

the other need the nut on the pully loosened and the threaded pole loosened will move the pully removing tension from the belt (opposite will tension the new belt).

tighten belt until you can only twist it in half.

Jun 25, 2009 | 2003 Toyota Camry

1 Answer

How do you replace a belt tensioner on a 2000 dodge grand carvan?

before you start you need to make sure that you have the sticker with proper routing of the belt to install the new tensioner and if not make a picture of it this will save a lot of time. next if you haven't already purchaced your part i would recomend any auto part store it will be cheaper than the dealer.most tensioners can be removed with a 3/8 or 1/2 ratchet or breaker bar to fit into the slot on the tensioner. pull one way or the other to release the tension and remove the belt off the pully then you will need a socket or wrench to remove the pully then install new part and belt, check to make sure belt is on all grooves and pully before starting.

Jan 03, 2009 | 2000 Dodge Caravan

1 Answer

Need to install new serpentine belt on 96 Jetta 2.0

that is your belt tensioner!! You pull that back when you are gettin ready to finnish putting your belt on the last pulley!! Follow diagram under hood for your specs on motor!!

Dec 07, 2008 | 1996 Volkswagen Jetta

Not finding what you are looking for?
2003 Ford Taurus Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides