Question about 2003 Dodge Caravan

Open Question

Diagram for rear drum brake 2003 dodge minivan\

Diagram for rear brake shoe assembly

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
280zlvr
  • 126 Answers

SOURCE: REAR BRAKES

i think your aware of how to change the brakes if im right and your problem is the rusted drum doesnt want to come off the only way to get the old drum off is to remove adjuster plug from behind drum dustshield and adjust the shoes so that there not even close to the braking area of the drum then try and wiggle the drum off of the assembly if it is not coming off then you need to use the old nylon hammer on the drum and i mean you must hit the drum from side to side trying by hand to wiggle the drum off its a tight fit and you need to strike the drum on the face not on the fins not wanting to damage with persistance and care and patience you will eventually be able to remove the drum to service brakes take care and good luck with it

Posted on Jul 01, 2008

Ad
  • 718 Answers

SOURCE: How do you get the rear brake drum off?

2003 dodge neon sxt

Here are the steps;
) Park on a level surface. safety
) Block all the other wheels. safety
) Put the vehicle gearshift in PARK. safety
) Release the handbrakes.
) Slightly break the rear wheel lug nuts seal while on ground. Just loosen do not remove.
) Jack up the rear wheel.
) Check to see the wheel will turn so you know the brake shoes are not binding against the drum.
) Now you can remove the lug nuts and wheel.
) Remove the drum. Some times the drum has frozen on with rust. You may have to use a hammer and hit along the drum near the outer edges to break it free.

Posted on May 08, 2009

pippall
  • 1486 Answers

SOURCE: 2001 dodge neon rear drum removal wheel cylinder

You need a pullers to get it off.But if your lucky putting a screwdriver between the drum and back-plate and pize it when your hitting with a hammer it may come off.good luck.

Posted on Jun 03, 2009

  • 1986 Answers

SOURCE: Rear drum brakes system operation

I believe the bar should have a spring attached to it or relatively close by. when you let go of the brake, the spring pulls the shoes off of the drum and the bar keeps the brakes where they are and does not allow them to be pull back too far away from the drum

Posted on Sep 16, 2009

jturcotte
  • 8587 Answers

SOURCE: I need a diagram for rear drum brake assembly

is this the one you have?53adb72.gif9e25d21.gif

Posted on Oct 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Parking brake stuck


where the cables connect to the rear parking brake shoes is like a hook shape waht iv seen happen is thay rust and stick after being aplied only real fix is to remove and free them up and re assemble the parking brake taking the cables off wont release the shoes from teh drum and will cause more damage in more parts will be needed to compleat the repair

Feb 28, 2014 | Dodge Dakota Cars & Trucks

1 Answer

Cannot put on rear brake drum on 2003 dodge dakota


Back the adjuster start wheel off to fit the drum, you have the shoes maladjusted.

Oct 14, 2012 | 2003 Dodge Dakota Club Cab

1 Answer

How do you release the rear brakr shoes to remove the drum and bearings?


Remove or disconnect the following:
  • Rear wheel
  • Wheel speed sensor, if equipped
  • Brake drum, bearing and spindle assembly
  • Brake shoe hold-down springs and pins
  • Brake shoe assembly from the wheel cylinder and anchor block
  • Parking brake cable
  • Lower return spring
  • Upper return spring
  • Primary shoe from the strut and brake shoe adjuster
  • Parking brake return spring
  • Secondary shoe from the strut support
I hope this answers your question. Best of luck!
Greg

Jun 28, 2011 | 2003 Ford Focus

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

1 Answer

I need a diagram of the rear brakes of a 1997 Intrepid Chrysler-where can I get one>


If the following is not enough then maybe try Alldata.com which generally has more information, but it will cost: REMOVAL & INSTALLATION Chrysler Concorde, New Yorker, LHS Dodge Intrepid Eagle Vision
  1. Remove the rear wheels and brake drums.
  2. Remove the dust cap from the rear hub and bearing assembly.
  3. Remove the cotter pin, nut retainer and wave washer. Discard the old cotter pin.
  4. Remove the rear hub and bearing assembly retainer nut and washer. Remove the rear hub and bearing assembly from the spindle.
  5. Remove the automatic adjuster spring from the adjuster lever.
  6. Rotate the automatic adjuster starwheel enough so both shoes move out far enough to be free of the wheel cylinder boots.
  7. Disconnect the parking brake cable from the actuating lever. Disconnect parking brake cable one side at a time.
  8. Remove the both lower brake shoe to anchor springs.
  9. Remove the 2 brake shoe hold-down springs from the brake shoes.
  10. Remove the brake shoes, upper shoe-to-shoe return spring, automatic adjuster and automatic adjuster lever from the backing plate as an assembly.
  11. Separate the brake shoes from the automatic adjuster mechanism.
  12. Remove the brake shoe automatic adjuster lever from the leading brake shoe. To install:
  13. Thoroughly clean and dry the backing plate. To prepare the backing plate, lubricate the bosses, anchor pin and parking brake actuating lever pivot surface lightly with lithium based grease.
  14. Remove, clean and dry all parts still on the old shoes. Lubricate the starwheel shaft threads with anti-seize lubricant.
  15. Assemble both brake shoes, the top shoe to shoe return spring, automatic adjuster and automatic adjuster lever before mounting on vehicle. Make sure the ends of the automatic adjusters are positioned above the extruded pins in the webbing of the brake shoes prior to installation.
  16. Install the brake shoe assembly onto the brake support plate and install the hold-down springs.
  17. Install the lower anchor springs and reconnect the parking brake cable to the park brake lever of the trailing brake shoe.
  18. Rotate the serrated adjuster nut to remove the free-play from the adjuster assembly.
  19. Install the automatic adjuster lever spring on the lead brake shoe assembly and the automatic adjuster lever.
  20. Install the rear hub and bearing assembly. Install washer and retainer nut and torque to 124 ft. lbs. (168 Nm).
  21. Install the wave washer, nut retainer and a new cotter pin onto the spindle. Install dust cap.
  22. Adjust brake shoes so not to interfere with brake drum installation. Install the rear brake drum. NOTE: After installing the brake drums, pump the brake pedal several times to partially adjust the brake shoes. To verify proper operation of the self-adjusting parking brake, be sure that both rear brakes are not dragging when the parking brake pedal is released.
  23. Install the rear wheels and lug nuts. Torque the lug nuts, in a star pattern sequence, to 95 ft. lbs. (129 Nm).
  24. Road test the vehicle. The automatic adjusters will continue brake adjustment during the road test of the vehicle.
prev.gif next.gif

Sep 03, 2010 | 1997 Dodge Intrepid

2 Answers

Chrysler Town & Country Minivan Rear Drum Brakes


I replaced the brake pads on a '94 Chrysler town and country, I had the rotors turned also, I did not use any anti-vibration substance on the shoes. I hear a clicking noise from front brakes.

Apr 16, 2010 | 2005 Chrysler Town & Country

1 Answer

Rear drum brake assembly


google rear break drum

Aug 29, 2017 | 1993 Ford Econoline

4 Answers

Rear drum brakes system operation


I believe the bar should have a spring attached to it or relatively close by. when you let go of the brake, the spring pulls the shoes off of the drum and the bar keeps the brakes where they are and does not allow them to be pull back too far away from the drum

Sep 16, 2009 | 2003 Dodge Caravan

2 Answers

I need a diagram for the rear drum brake for 2002 Ford Ranger


Copy and paste this into your search window: 2002 ford ranger rear brake diagram

You should see four pictures pop up, select the brake parts diagram or the brake picture.

Sep 03, 2009 | 1993 Ford F150 SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...