Question about 1984 Cadillac Eldorado

Open Question

Vapor canister leak

Intermittent leak after turning off engine

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ftw1952
  • 10319 Answers

SOURCE: The fuel vapor canister on

Was the vapor canister solenoid replaced as well? If no do so for they leak as well

Posted on Apr 12, 2011

Ad
  • 514 Answers

SOURCE: vapor canister 2003 cadillac cts

it will look something like this:
1_10_2012_5_20_27_pm.jpgand is usually located on the fender well on the engine side toward the front corner of the car (it may be inside the fender itself)
there would be 2-3 large vacuum hoses going to it which will help in finding it.

Posted on Jan 10, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 chevrolet Colorado 3.5 intermittent gas smell in cabin


Usually if you smell gas in the cabin the odor is coming in thru the vents from the engine compartment. Is there a fuel leak around the engine or the vapor canister ?

Aug 05, 2014 | Cars & Trucks

1 Answer

Evap emmission,control sys leak


Do not top off your gas tank. The gas is going into carbon canister which is only for fuel vapors to go into (carbon canister opening near the top of fuel neck near the gas cap). Your flooding the fuel vapor canister with liquid fuel; of course you are going to get a sensor message... 'Evap emmission,control sys leak

P0443 The fuel vapor canister reduces that gas smell on hot days outside/inside of car. The fuel vapor canister fillers bad smells from gas tank on hot days when the gas expands and burps fumes through carbon canister filter. From the canister (gas vapor fumes) goes back into the engine to be burned again...it's a closed loop for vapors to be recycled though engine. Don't worry, once the carbon canister dries out and no longer flooded with raw fuel the code should go away...just don't let the top off fuel tank back flow into the 'Evap emission control' carbon filter near the top and close to the gas cap...:)

Apr 20, 2014 | 2000 Ford Mustang

2 Answers

My 1995 subaru legacy lsi cuts out when I rev the engine around 1 rpm. Plus the check engine light is on. I took it to the dealership and they couldn't fix it, but they got a code from the check engine...


code p 0441 refers to evaporative emission (EVAP) system --incorrect flow detected ==== causes --- hose connection/s--- intake leak---EVAP canister purge valve replace the purge valve

May 21, 2017 | 1995 Subaru Legacy

1 Answer

1996 Ford Aerostar 3.0 L V-6 Constant check engine light ON Ran codes. Code says vacuum leak on fuel canister. I'd like to change all the vacuum lines. Don't have a good schematic. Haynes manual only...


what codes?

The vacuum lines run from the canister to the intake manifold. One is the purge hose to deliver stored fuel vapor to the intake to be burnd when engine is warm and you are crusing at part throttle. The other line is the vacuum line to operate it.

Fuel Vapor Valve, Aerostar (4.0L Engine) The evaporative emission valve (9B593) uses a small orifice, 1.83mm (0.072 inch), that allows vapors to pass into the vapor line running forward to the evaporative emissions canister (EVAP canister) (9D653). This evaporative emission valve mounts directly into the fuel tank (9002) using a fuel vapor separator seal. Fuel vapors trapped in the sealed fuel tank are vented through the orificed evaporative emission valve. The vapors from the fuel tank leave the evaporative emission valve through a single vapor line and continue to the evaporative emissions canister in the engine compartment for storage.
-----------------------------------------------------
Fuel Vapor Canister Purge Regulator Valve, Aerostar, Ranger Removal and Installation
  1. Disconnect wire harness from evaporative emission canister purge valve (EVAP canister purge valve) (9C915).
  1. Disconnect wire harness from thermistor.
  1. Disconnect evaporative emission canister purge valve assembly from fuel vapor canister and throttle body.
  1. To install, reverse removal procedure.
-----------------------------------------------------------------

snorkelbobby_48.gif

Mar 25, 2011 | Ford Aerostar Cars & Trucks

1 Answer

Describe your Problemcheck engine light codes p0457 p0455


Trouble code P0455-EVAP Control System Large Leak Detected

Trouble Code Conditions:
ECT sensor less than 90°F at startup, engine running, and the PCM detected several small fuel vapor leaks or a large leak in the system.

Possible Causes:

  • Aftermarket EVAP hardware non-conforming to specifications
  • Canister vent (CV) solenoid stuck open
  • EVAP canister purge valve stuck closed, or canister damaged
  • EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube disconnected or cracked, or canister is damaged
  • Fuel filler cap missing, loose (not tightened) or the wrong part
  • Loose fuel vapor hose/tube connections to EVAP components
  • Purge sensor or FTP sensor is out of calibration or has failed

Jan 22, 2011 | 2006 Ford Explorer

1 Answer

You can smell gas all around the car, but cannot tell that any gas is leaking. The vapor canister looks fine, but can see gas below the engine on the tyrod connector.


Check fuel lines that run up side of engine. Lots of times they can chaffe against block and leak. Also be careful when filling car, if you top tank to top of fill neck that puts pressure on lines to canister where canister will fill w/fuel and literally ruin vapor canister.

Jan 02, 2011 | 1997 Chevrolet Cavalier

1 Answer

Obd-2 code p1455


DTC P1455 - Substantial Leak or Blockage in Evaporative Emission Control System

The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).

Check this possible causes:
After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
EVAP canister purge valve stuck closed
Damaged EVAP canister
Damaged or missing fuel filler cap
Insufficient fuel filler cap installation
Loose fuel vapor hose/tube connections to EVAP system components
Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
Canister vent (CV) solenoid stuck open
Mechanically inoperative fuel tank pressure (FTP) sensor


Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank

Tell us news.

Jul 19, 2010 | 1996 Ford Explorer

2 Answers

Check engine light code PO442


You likely won't notice any drivability problems. P0442 indicates a fuel vapor leak in the EVAP control system. It means a very small leak has been detected. In fact, the leak can be from a hole as small as 0.04" in diameter. 
The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage.
Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

With a P0442, the most common repair is to Remove and reinstall the gas cap, clear the codes, and drive for a day and see if the codes come back. Otherwise, replace the gas cap, or Inspect the EVAP system for cuts/holes in tubes/hoses.

Good luck and hope this helps

May 07, 2009 | 2001 Volvo S60

1 Answer

Check engine light is on for emission evaporator failure-large


P0455 - EVAP Control System Leak Detected (No Purge Flow or Large Leak) The PCM monitors the complete EVAP control system for no purge flow, the presence of a large fuel vapor leak or multiple small fuel vapor leaks. The system failure occurs when no purge flow (attributed to fuel vapor blockages or restrictions), a large fuel vapor leak or multiple fuel vapor leaks are detected by the EVAP running loss monitor test with the engine running (but not at idle).
  • After-market EVAP hardware (such as fuel filler cap) non-conforming to required specifications
  • Disconnected or cracked fuel EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube
  • EVAP canister purge valve stuck closed
  • Damaged EVAP canister
  • Damaged or missing fuel filler cap
  • Insufficient fuel filler cap installation
  • Loose fuel vapor hose/tube connections to EVAP system components
  • Blockages or restrictions in fuel vapor hoses/tubes (items also listed under disconnections or cracks)
  • Fuel vapor control valve tube assembly or fuel vapor vent valve assembly blocked
  • Canister vent (CV) solenoid stuck open
  • Mechanically inoperative fuel tank pressure (FTP) sensor
Check for audible vacuum noise or significant fuel odor in the engine compartment or near the EVAP canister and fuel tank. ----------------------------------------------------------------------------- HX43 DTC P0457: CHECK FOR MISSING OR LEAKING FUEL FILLER CAP
  • Check for missing fuel filler cap.
  • Check for loose fuel filler cap.
  • Check for possible cross-thread fuel filler cap condition.
Is a fault present concerning the proper installation of the fuel filler cap? Yes No REPLACE cross-threaded or damaged fuel filler cap. RECONNECT and TIGHTEN the fuel filler cap only one eighth turn so that the cap initially clicks by sound or touch. CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test . If DTC P0455 or P0457 is present, Go to HX44 . CLEAR Continuous Memory DTCs. COMPLETE an Evaporative Emission Running Loss Monitor Repair Verification Drive Cycle (refer to Section 2 , Drive Cycles). RERUN Quick Test .

For DTC P0455 still present: Go to HX44 .

Otherwise, INFORM the vehicle owner that it is important and necessary to immediately install the fuel filler cap after every refueling event. HX44 DTC P0455: VISUAL INSPECTION FOR SUBSTANTIAL EVAPORATIVE EMISSION SYSTEM LEAKS
  • Check for missing fuel filler cap. If the cap is loose DO NOT DISTURB EVAP system.
  • Verify that both the input port vacuum hose and EVAP return tube are attached to the EVAP canister purge valve. Note: If the EVAP canister-CV solenoid assembly is not accessible during this pinpoint test step, GO to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for disconnected or cracked fuel vapor hoses/tubes between the intake manifold, the EVAP canister purge valve, the EVAP canister, the fuel vapor vent valve assembly and if applicable the fuel vapor control valve tube assembly.
  • Check for damage to the fuel filler pipe and the fuel tank.
Is a fault indicated? Yes No CONNECT or REPLACE fuel vapor hoses/tubes as required. REPLACE damaged EVAP system components (fuel filler pipe, fuel vapor vent valve assembly, fuel vapor control valve tube assembly, EVAP canister purge valve, FTP sensor and EVAP canister-CV solenoid assembly) as necessary. REFER to Evaporative Emissions, Section 303-13 in the Workshop Manual for removal and installation instructions. GO to HX45 . GO to HX45 . HX45 DTC P1443 and P0455: CHECK FOR EVAPORATIVE EMISSION SYSTEM LEAKS
    Note: When checking for leaks or blockages in the EVAP system, energize (close) the canister vent (CV) solenoid through the scan tool for a maximum of nine minutes per pinpoint test step. Then de-energize the CV solenoid prior to performing the subsequent pinpoint test step. This is done to assure proper closing of the solenoid.
  • Disconnect and plug the EVAP return tube (EVAP canister purge valve to intake manifold) at the intake manifold vacuum source.
  • Connect scan tool.
  • Key on, engine off.
  • Access VPWR PID. If the voltage is not 12 volts or greater, GO to HX61 .
  • Locate evaporative test port [marked EVAPORATIVE SERVICE PORT DO NOT USE UNREGULATED PRESSURE ABOVE 6.89 kPa (1 PSI)] near EVAP canister purge valve or EVAP canister.
  • If vehicle is not equipped with the evaporative test port, GO to HX50 .
  • Install the Rotunda Evaporative Emission System Leak Tester 310-F007 (134-00056) or equivalent at the evaporative test port.
  • Close CV solenoid by accessing Output Test Mode on the scan tool.
  • Select ALL OFF mode and push START button.
  • Regulate the nitrogen or argon gas pressure on the tester to 3.48 kPa (14 in-H 2 O).
  • Follow the instructions that come with the EVAP System Leak Tester and pressurize the EVAP system.
  • Perform the EVAP system leak test.
Does the pressure on the EVAP system stay above 1.99 kPa (8 in-H 2 O) and pass the leak test? Yes No GO to HX46 . REMOVE the EVAP System Leak Tester from the evaporative test port and REINSTALL the test port cap. GO to HX50 .

Apr 15, 2009 | 1999 Lincoln Town Car

1 Answer

My taurus failed due to code p0442 ecap emiss ctl sys leak detected (small leak)


    Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
    Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.
    • After market parts and accessories nonconforming to the EVAP system specifications.
    • Damaged, cross threaded or loosely installed fuel filler cap.
    • Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
    • Loose fuel vapor hose/tube connections to EVAP system components.
    • EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
    • CV solenoid partially open when commanded closed.
    • EVAP canister leaking.
  • Check for presence of fuel filler cap.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
    • EVAP canister to EVAP canister purge valve.
    • EVAP canister to fuel vapor vent valve assembly.
    • fuel vapor control valve tube assembly to fuel tank (if applicable).

Jun 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...