Question about 1986 Ford Ranger 2WD

Open Question

How to change flex plate on 86 ford ranger - 1986 Ford Ranger 2WD

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: 86 ford ranger

its under the carpet on the passanger side at the firewall

Posted on Jul 21, 2008

Ad
wilsodfarm
  • 986 Answers

SOURCE: flex plate torque bolt ratio f-250 ranger 1981 400

35 ft lbs

Posted on Oct 01, 2009

  • 279 Answers

SOURCE: What parts will I need when changing a flex plate?

While you have the transmission removed be sure to replace the rear main bearing seal.On a1982 you will have to remove the oil pan to replace the seal,It has a two piece seal.After removal of the oil pan carefully remove the back main bearing cap,you will have to use a straight pick to roll the top seal out of the block.Lubricate the deal with oil before you install it.Be sure to get a new oil pan gasket with your other parts.Make sure you torque your main bearing cap to manufacturer's specifications.

Posted on Jan 31, 2010

Testimonial: "Thank you. That does help me for my future project. Pat"

jgwhomeequip
  • 1902 Answers

SOURCE: how to change the clutch

The 1st step is to loosen your bell housing bolts and drop your starter. The remove your drive shafts the front drive shaft will slide out from the front and then pull it back to the rear. Then you must take your shifter lose from the Trans not the diff. then drop your cross member. Do not take the transfer case lose from the trans. If you can help it. You will then remove the trans. And unbolt the pressure plate. And everything should come off, make sure when you reinstall the clutch plate that you make sure the side that said to fly wheel is against the fly wheel. Make sure you tighten the pressure plate and clutch plate up with you line up tool all the way in and don't be afraid to tighten down on it. Because it isn't easy getting the Trans back up in there. The reassemble in the same order.

Posted on Jun 08, 2011

charliesloan
  • 5 Answers

SOURCE: will a 87 ford ranger v6 4 wheel drive trans. fit

chance the motor as well to make easier. otherwise youll need a standard ****** for the 4 cyl

Posted on Oct 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a 86 Ford ranger spark plug diagram


https://www.google.com/search?q=86+ford+ranger+spark+plug+diagram&tbm=isch&imgil=ChAyBXLWz1uEmM%253A%253B6p7Wh6PGke8PMM%253Bhttp%25253A%25252F%25252Fwww.therangerstation.com%25252Ftech_library%25252F2_9_Page.html&source=iu&pf=m&fir=ChAyBXLWz1uEmM%253A%252C6p7Wh6PGke8PMM%252C_&usg=__ZS-6FtD-mg1urpuXuWpFu1C0x7w%3D&biw=1024&bih=638&ved=0ahUKEwiXtpyvrI7TAhWj6oMKHTdjAugQyjcIOQ&ei=OW3lWNe1MKPVjwS3xonADg#imgrc=ChAyBXLWz1uEmM:

Apr 05, 2017 | Ford Cars & Trucks

1 Answer

Will a motor out of a 1986 interchange with my 1990 ford ranger


Should bolt in, depending on size of the motor if it's the same 3.8, or 4.0 (6 cylinder) or four cylinder. The problem with using a different size is wire harness, exhaust and the peripherals. But 86 to 90 didn't change very much it's after 93 that Ford made a lot of changes. Hope this helps...

Nov 07, 2015 | Ford Cars & Trucks

1 Answer

Is there a proper alignment for a flexplate on a 93 ranger 4.0 ohv engine? The mounting holes are equally spaced and I did not mark how it came out.


If you look at the flex plate it might have a weight welded to it at one point. Flex plates are balanced before they are mounted to the crankshaft, so as long as the holes line up and all the bolts go in, your good.

Jul 30, 2011 | Ford Ranger Cars & Trucks

1 Answer

2003 Ford Ranger Extended Can 3.0L V-6 Flex Fuel Automatic Transmission. I put a new motor in my little truck and now the transmission acts like its in neutral. I just found out the transmission is...


How do I change the 2003 Ford Ranger XLT 3.0 L Flex Fuel -Auto Trans 2wd Camshaft synchronizer and sensor . Do I need any special tools ? Are there after market parts that are precise replacements for the OEM parts ?

Aug 07, 2009 | Ford Ranger Cars & Trucks

1 Answer

Have a 86 ford ranger 2.3 l 4cy in mornings


its your fule filter theres 2 of them i the 86 ford ranger you need to change them the location of the fule filters are on google just tipe in fule filter 1986 ford ranger location it should pop up there about 8 dollors a peace easy fix and your truck is like new also get a new battey if you havent k have a good day. oh i know this because i own one had the same problem

Apr 02, 2009 | 1986 Ford Ranger 2WD

1 Answer

86 ford ranger


its under the carpet on the passanger side at the firewall

Jul 20, 2008 | 1986 Ford Ranger 2WD

1 Answer

86 ford ranger not running


check the fuel pressure for the fuel pump first

May 27, 2008 | 1986 Ford Ranger 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...