Question about Ford Ranger

Open Question

2000 ford ranger rpm sensor location

4.0

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: 2000 ford ranger wont start

on the passenger side underneath the engine.

Posted on Jun 24, 2008

Ad
emissionwiz
  • 76164 Answers

SOURCE: speed sensor diagram for 2000 ford ranger

It is in the hole (held in place by a Y shaped clamp) where the speedo cable used to go on the side of the trans, has 2 wires coming out of it, it is round with a round connector. Is this for an ABS problem? if so the sensor is on the top of the differential housing.

Posted on Nov 06, 2008

  • 2 Answers

SOURCE: air bag sensor

A possible solution. i have a 2002 ranger in which the air bag light would present itself. i discoved that the passenger air bag indicater bulb was out if i had the airbag on or off. its located next to the key switch. i pulled it appart and notice the bulb was bad. replacing it fixed the problem. there is a catch. this bulb is solderd to the circuit board and you have to get it from radioshack. is a simple task if have a solder kit. hope that helps.

Posted on Jan 09, 2009

Ajkill
  • 2035 Answers

SOURCE: 2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???

Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Posted on Jan 16, 2009

the recycler
  • 22 Answers

SOURCE: location of the egr sensor on 2000 ford ranger

The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 Ford Ranger RPM seems too high when first


I would check for any vacuum leaks. Also, is the check engine light on?

May 11, 2010 | 1985 Ford Ranger

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Speed sensor diagram for 2000 ford ranger


This video shows the speed sensor and its location for a 2000 ford ranger xlt. It also describes the problems a bad sensor can give.

Nov 06, 2008 | 2000 Ford Ranger SuperCab

1 Answer

Diagrams


your oxygen sensor or sensors are located on your exhaust pipe just after your exhaust manifold

May 26, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...