Question about Geo Prizm

1 Answer

1990. How do I reinstall the cross member?

Im replacing the transmission in my geo prism 1990 the transmission and starter are bolted in im trying to put the cross member back on and cannot figure out exactly how it goes back on

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Geo Master
  • 20,706 Answers

Im tire of look at this old post
jacket and bolt it, there.

Posted on Aug 12, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: location of fuel filter-1990 Geo Prism

Right under the master brake cylinder, its really hard to replace it. It has 2 screws, one bolt on top and the bottom one needs to be screwed off under the car

Posted on Oct 03, 2008

  • 9 Answers

SOURCE: Fuse replacement for 94 Geo Prism

just unbolt it and replace it, that easy

Posted on Mar 18, 2009

jonathancole
  • 127 Answers

SOURCE: PO 136 GEO PRISM 1997

it is o2 curcuit (bank 1 sensor 2)

Posted on Aug 13, 2009

agent91
  • 2100 Answers

SOURCE: my ABS light is staying on - 1995 Geo Prism

Your abs light is permanent. Most people don't bother to fix this, it is expensive, and your car is getting old. It means that the anti lock brake system has failed and needs repair. But your brakes still work fine, just don't have anti lock. So I'm not saying tape over the light on the dash, but.

Posted on Apr 08, 2010

  • 59 Answers

SOURCE: 1994 geo prism, fuse blew, I don't have manual

the only fuse for the starter is not located in the fuse box it is located in the positive wires that go to the starter its called a fusible link and when then amperage of the starter exceeds the fusible link rating the fusible link blows the link is usually located inthe positive wire to the starter and at some point fatter then the wire itself

Posted on May 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Changing flywheel on a Chevy four wheel drive454


borrow a puller and a impact driver and a compressor and some impact tools and sockets and replace the seal while yur down there eating road grime! Arrr!

Apr 21, 2015 | Chevrolet Cars & Trucks

1 Answer

How to remove starter from 2004 pacifica


REMOVAL
Disconnect the negative battery cable.
Remove (UPPER RADIATOR CROSS MEMBER) and relocate (UPPER RADIATOR CROSS MEMBER REMOVED) the upper radiator crossmember, (Refer to 23 - BODY/EXTERIOR/RADIATOR CROSSMEMBER - REMOVAL).
Remove the radiator fan module (FAN MODULE IN VEHICLE) (Refer to 7 - COOLING/ENGINE/RADIATOR FAN - REMOVAL).
Remove the wiring harness clip from front mount.
Remove the coolant line clamp bolt (COOLANT LINE BRACKET).
Remove the upper nut from the front mount (FRONT RUBBER MOUNT UPPER NUT).
Remove the upper starter mounting bolt (UPPER STARTER BOLT).
Remove the middle starter bolt (MIDDLE STARTER BOLT).
Raise vehicle and support.
Remove the lower front mount nut (FRONT RUBBER MOUNT IN POSITION).
Raise and support engine (SUPPORT ENGINE).
Remove the lower bracket bolt to transmission (BRACKET TRANS BOLT).
Remove the lower bracket bolt to engine block (BRACKET ENGINE BLOCK BOLT).
Relocate the front mount and bracket.
Disconnect the positive battery cable from starter
Disconnect the solenoid connector from starter.
Remove the lower starter bolt (STARTER LOWER BOLT).
Remove starter from vehicle.

Aug 16, 2011 | 2004 Chrysler Pacifica

1 Answer

Clutch is worn out. How hard is this to repair myself?


You will have to a floor jack to jack the transmission up, to unbolt and pull the transmission, Un bolt the pressure plates and pull off the clutch and pressure plate assembly. To reassemble you have to use a clutch alighnment tool, place the new clutch disk against the flywheel, insert the alighnment toll and bolt down the new pressure plates. Reinstall the transmission by turning the back spline to alighn the front spline(must be in first gear not neutral) slide into position and bolt back in place. There will be a cross member with a rubber mount going to the transmission that will need to be removed first thing.

Feb 24, 2011 | 1996 Geo Prizm

2 Answers

Remove starter from 2005 gmc envoy denali. I can't get at the wires to disconnect them.


YOU HAVE TO REMOVE REAR STEERING GEAR CROSS MEMBER.REMOVE THE WIRE HARNESS FROM THE WIRE HARNESS RETAINING CLIPS ON THE TRANSMISSION OIL COOLER LINE BRACKET.REMOVE TRANSMISSION OIL COOLER LINE BRACKET BOLT.REMOVE RIGHT TRANSMISSION COVER BOLT.THEN REMOVE STARTER BOLTS THEN REMOVE STARTER.

Sep 06, 2010 | 2005 GMC Envoy Xl

1 Answer

1994 geo prism, fuse blew, I don't have manual


the only fuse for the starter is not located in the fuse box it is located in the positive wires that go to the starter its called a fusible link and when then amperage of the starter exceeds the fusible link rating the fusible link blows the link is usually located inthe positive wire to the starter and at some point fatter then the wire itself

May 04, 2010 | 1990 Geo Prizm

1 Answer

I need to replace the transmission mount on a '94 1500 4.3L, 4X4. Which is easier, support the transmission and remove the cross member or release the engine mount bolts and raise the drive train? Tks


Supporting the transmission while removing the cross-member is easier. You will have the engine mount holding the whole thing in precise place, while you deal with the crossmember, and the transmission.

Comparing: if you release the engine mount bolts and jack up the drive-train, the whole thing would shift, and you could have trouble when the cross-member fails to go up well enough.

On the other hand, if the cross-member bolts fail to release due to "home-mechanic" syndrome, you have only the first option.

Dec 03, 2009 | 1994 GMC Sierra

1 Answer

Change transmission instructions


this is for rear wheel drive only front wheel drives require removing axle shat and dropping tie rod end and lower ball joint to get tranny out. If you start this I will give tork setting when I know what you have as it is a lot of work to type this out.

First disconnect the battery, inside the cab pull shifter boot off and remove snap ring to remove shifter, next get a block to go under engine remove drive line bolts and be sure E-brake is set and block the wheels, next put bolts from driveline into the read differential in order so you will be able to find them next disconnect the two starter bolts from the starter and tie starter up as not to allow the starter weight to hang on the wires. Remove two bolts holding slave cylinder on let hang off the side do not lose the shaft out of slave. Next remove the transmission mount bolt out next pull four bolts out of transmission cross member, next remove 5 bolts out of bell housing now get a baggie and a couple of rubber bands and pull drive shaft slide baggie over the transmission tail shaft and put on rubber band on bag to keep from losing fluid move drive shaft out of the way. Next disconnect the Speedo cable and wiring harness the reverse switch is at the top so will have to drop the tranny down to keep from breaking wire. Once you have a gap between the transmission and engine put block under back of engine slide the transmission out let the front drop down then lift up on rear of transmission and slide the cross member out of the way. Next slide tranny out of the way next remove the 6 bolts on the clutch assembly turning each bolt 1 and a ½ turns each till clutch is loose remove the clutch pressure plate and the throw out bearing, remove flywheel take to machine shop and have surfaced, replace the clutch plate pressure plate and the throw out bearing reinstall in reverse if you see any oil leaks replace seals, also replace rear transmission seal now if you don’t it will leak next after it is back together be sure you put new fluid in the transmission and bleed the slave cylinder.

Jun 28, 2009 | Nissan Pickup Cars & Trucks

1 Answer

What is the starter location on a 1990 geo prism?


Look to the rear of the engine way down low by the fly wheel. Good luck.

May 08, 2009 | 1995 Geo Prizm

1 Answer

Ford transmission installation


you will have to take the cross member off to get the old one outand to put the new one in. the cross memeber was put there so people would have to take it to a shop but there are 4 bolts 2 on each side and then whatever bolts are screwed to the transmission.

Feb 20, 2009 | 1990 Ford F150

2 Answers

Location of fuel filter-1990 Geo Prism


Right under the master brake cylinder, its really hard to replace it. It has 2 screws, one bolt on top and the bottom one needs to be screwed off under the car

Aug 06, 2008 | 1990 Geo Prizm

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...