Question about GMC Envoy XL

1 Answer

Envoy hatch lock

Rear glass on my 05 envoy never locks,the alarm will go off if some one opens it,but only for a little while and then will reset itself

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • GMC Master
  • 1,138 Answers

There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Posted on Apr 19, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 188 Answers

SOURCE: liftgate ajar is on

Great Job-emissionwiz

Posted on Feb 01, 2009

  • 1 Answer

SOURCE: rear hatch door won't lock dash light showing

You need to tighten the lock mech on the boot lid. this will close the boot just enough more to turn the light on. It's no biggy, you might need a star driver depending on bolt head. move it into the boot lid approx 4mm to start. then 1mm until 10mm. if no joy then it may be the sensor.
All the best
Ally A

Posted on Jul 25, 2009

smartr10U
  • 1305 Answers

SOURCE: Rear hatch and barn doors will not lock or alarm

In time with usage, the electric locks in the doors and gates wear out.
You can purchase replacement parts... a little involved to change but doable.
I suggest a Haynes manual for photos for disassembly .
(I've got a 2001 and all 4 doors eventually quit...bought replacement parts at local dealer)
k

Posted on Sep 25, 2009

  • 1 Answer

SOURCE: rear hatch 2005 chevy tahoe is locked & won't open

my 06 tahoe just got this problem...all other doors lock and unlock with the fab and door switch...but the hatch is in permanent locked mode. i cant even unlock the hatch window. why is this happening?

Posted on Mar 09, 2010

  • 389 Answers

SOURCE: 2006 Tahoe Rear Hatch lock actuator

A wrecking yard is your best bet. The odds of you getting one that is bad are astronomical. Are you sure your remote has fresh battery's? Also check your fuse going to that devise before buying another one. The second choice on where to find one is eBay. Of course they are usually higher then a wrecking yard. They get a lot of there parts for sale by going to the salvage yard them selves. I hope this helps and Good Luck, The Raz

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I open the cargo door if it wont open?


rear door hatch lock repair GMC Chevrolet - YouTube

? 4:26
https://www.youtube.com/watch?v=QS3PMhGgyAg
Apr 5, 2014 - Uploaded by auto resource
2002 Yukon, rear hatch lock not locking. ... rear door hatch lock repair GMC Chevrolet. auto resource ... chevy tahoe lift gate notopening - Duration: 2:12. ... A Method how to unlock your car in 10 seconds :) - Duration: 0:35.

chevy tahoe lift gate not opening - YouTube

? 2:12
https://www.youtube.com/watch?v=xU6ybiY3F4I
Sep 1, 2010 - Uploaded by 76bluemoon
Back lift gate/glass would not open or release. Even when unlocked with the key fob or the unlock switch on the drivers/passenger door. ... How To Install Replace Rear Lift Gate handle 2002-09 GMC Envoy Chevy Trailblazer ...

Jan 16, 2016 | 2002 Chevrolet Tahoe

1 Answer

My toyota kluger Grande 2009 alarm goes off randomly... Usually after using the rear glass hatch. I close the glass hatch, Remote lock it and within a couple of hours the alarm is going off.


If there are any insects or such the motion detector in your car may be detecting them. Your opening and closing of the hatch may be letting something in??

Aug 01, 2015 | Toyota Cars & Trucks

1 Answer

1992 Pajero rear hatch lock will not disengage to open door


My Envoy does that too. I figured out the unlock automatic setting on my keys had to be pushed twice!

Sep 21, 2014 | Cars & Trucks

1 Answer

How to repair rear actuator for ford escape hatch


Bad lock actuator: (NOTE: If your hatch is locked)
First remove rear panel- pull the plastic panel at the top center, until (2)clips pop off, then pop (2) more clips at the mid-center. Stick your arm down until you reach the lock, with your fingers, feel for the squishy plastic( inside is the bar that goes up to unlock), it is attached to the lever to unlock. Pull up the lever until you can open the hatch. There are four more clips at the top sides and middle sides, and four plastic screws at the bottom which is only accessible when the hatch is opened.
The lock is only sold as an assembly at $100.
Part Number #9L8Z-7843150 B

Apr 11, 2013 | 2010 Ford Escape XLT

1 Answer

2004 Highlander rear hatch sets off the alarm.


the switch is bad on the rear hatch cylinder

Aug 14, 2012 | Cars & Trucks

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

1 Answer

Troubleshooting rear lock on 1999 GMC Envoy


There are some mechanical rods in the rear hatch that are probably rusty and you will have to take the inner panel off to acces and clean them to get them moving to operate the lock.

May 09, 2010 | 1999 GMC Jimmy

1 Answer

2004 GMC Envoy rear hatch complete door wont


door lock actuator solenoid ( inside of door) needs to be replaced

Mar 25, 2010 | 2004 GMC Envoy

4 Answers

Rear hatch will not unlock on my 05 Denali


Check the unlock mechanism for the hatch. These are controlled by an electrical motor pulling a cable. If the cable came loose you might or might not hear the click click that it makes. I would also check the fuses and relays related to the system. Usually if you can get the interior panel off all the innards are exposed. I would suggest pulling that panel off, then triggering the keyless remote and see if anything moves, that might pinpoint where it has gone bad.

Sep 28, 2009 | 2005 GMC Yukon Xl Denali

1 Answer

Hatch problem


The glass did close and neither the glass or rear hatch would open. It did turn out to be the lower hatch switch which I had replaced.
Thanks for the follow up.

Nov 30, 2008 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...