Question about 2010 Dodge Challenger

Open Question

Dodge troubleshooting code P3040 I CHANGED THE CAM SENSOR AND ALSO THE CRANK SENSOR CLEARED CODE BUT STILL WILL NOT CRANK

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 137 Answers

SOURCE: 2003 stratus cam sensor replaced still unresolved

you bypassed the wires that connect to the sensors? that would have been my first guess the harness that plugs into the sensor. after that i would check the ground connection from the ecm. wouldn't hurt to check the battery posts too. if the battery posts are oxidized you can have all kinds of goofy electrical problems. hope that helps.

Posted on May 27, 2009

  • 1 Answer

SOURCE: 2003 stratus both sensors replaced still unresolved

Have the exact problem. Replaced cam sensor and timing belt. Still happens intermittently. code is p0344.

Posted on Jul 22, 2009

  • 98 Answers

SOURCE: have code p1391 and p0340, replaced both sensors

had similar problem with 99 ram. i made holes in crank sensor a bit bigger,removed rubber seal that sensor goes through in trans,installed 1 bolt and adjusted sensor back towards firewall and tightened that 1 bolt and its worked fine ever since

Posted on Aug 07, 2009

  • 2 Answers

SOURCE: 1997 Dodge Intrepid cranks over won't fire

I have this same NO START problem...
Began with tach giving readings not exceding 1200 rpm with strange 4000 + spikes.. Cruse control would not turn on or off at times and indicator light would only work sometimes..Had several episodes of excessive cranking to get it to start.. Stalling out while driving and even at freeway speeds.. Pulling the negative cable for 10 min. allowed it to start although with lots of cranking and put it in limp mode which required another computer reset to get out of.. Had thrown error codes related to cam and crank sensors which were replaced along with coil and manifold temp sensors.. Had the 9 volt power to sensors when key was on but the check engine light does not stay on with all the other idiot lights..
I wish people who respond would read the post first..
Original post states,
Cranks,No spark,No fuel pump run, changed some sensors ect...
If it cranks it ain't the neutral safety switch, starter or battery!! WAKE UP!!
Seems the computer is not turning on the coil, injectors or fuel pump for a reason.. Find that reason and you will find the solution to the problem.. Seeing as that the computers logic states are a dealer secrete the poster as I have changed many parts in blind hope that it will fix the problem.. Relays, sensors and ecu computer.. Did a visual check of all harness potential wear spots like where it crosses over the power rack..
Could it be in the wiring harness inside the dash??
Could it be a bad ground??
Can an alternator that has failed cause the computer not to start??
Can a bad oil pressure sensor cause the computer not to start??
Can signal loss from the TCU or BCU to the ECU cause this??
Is there an undocumented kill if the ECU thinks it was in an accident??
I can ground the relay line from the ECU and the fuel pump runs and pressures up and the other relays turn on as well..
This crank but no start problem seems to be common with a lot of 1994-2001 Dodge and Chrysler owners.. All these systems have become interlaced with undocumented safety features that baffle the DIYer..If you have seen this and have fixed it PLEASE RESPOND!!!!

Posted on May 02, 2010

yegarboy
  • 286 Answers

SOURCE: 1999 dodge ram 1500 318 engine no spark no signal

Check the ASD relay in the fuse box. Swap it with the starting relay. If the engine fails to roll over. Thats your problem. If not, check and see if your fuel injector connectors have voltage to them if not its a bad PCM. Hope this helps.

Posted on Jun 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dodge Avenger 2.4 wont crank code po 198. Po 11 change one cam sensor did not crank now it's telling me its the ex cam sensor what problems


Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
Best Manuals

Aug 24, 2016 | 2011 Dodge Avenger

2 Answers

My 2001 dodge neon cranked without the cam sensor connected. what's wrong with this picture?


Changing the Cam Position Sensor on Dodge Neon ...

? 10:33
https://www.youtube.com/watch?v=ciCPQ0kVAQY
Dec 21, 2012 - Uploaded by VeeTheAmazingGreek
... had to change out the cam position sensor on my 2001 Dodge Neon. ... 1997 Dodge Neon no start, crank sensor problems - Duration: 26:53.

Dodge Neon Questions - It will turn over but has no spark ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusAug 9, 2015 - I did have a neon while ago and image crank sensor was bad ... my 1999dodge neon has no spark it will turn over but not fire i have changed the crank sensorcoil ... I have a 2001 Dodge Neon 2.0 with 140,000 kms on it.

Dodge Neon Questions - 2001 Dodge Neon will turn over ...

www.cargurus.com > Questions > Dodge > Neon

CarGurusJan 7, 2013 - I have a 2001 Dodge Neon 2.0 with 140000 kms o... ... went about a month before this recent problem, fixed that with no problem now this. ... firing. you said you replaced the cam sensor, did you do the crank sensor as well? ... My 1996Dodge Neon won't stay running whenever I take my foot off of the gas.

Starting Issues and Trouble Code Due to Defective Cam ...

repairpal.com > Problems > Dodge > Neon

Feb 05, 2016 | 2001 Dodge Neon

2 Answers

P0238 dodge code


cam sensor failing, or crank sensor both do the same thing and is common fault they do get hot.

Oct 16, 2013 | 2005 Honda Civic 1.7i

1 Answer

Changed the crankshaft sensor and the cam sensor in a 04 jeep Cherokee Laredo and now the car stalled and gave code p3040


There is no P3040
If you meant P0304 it means you have a misfire on cylinder #4 and it needs to be investigated to determine why.

Aug 14, 2013 | Cars & Trucks

1 Answer

98 dodge avenger p1391 code, had no start first with no code and replaced dist..didnt fix it..then replace crank sensor and that worked..ben running fine for a year..now all of sudden runs crappy and...


Check connections to crank sensor, then reset your comp by disconnecting your battery cables and holding them together. Make sure to have the code cleared as well.

P1391 (M) Intermittent Loss of CMP or CKP Loss of the Cam Position Sensor or Crank Position sensor has occurred.

Apr 14, 2013 | 1998 Dodge Avenger

1 Answer

Dodge sx wont rev past 4000


might be worth checking the air intake for any blockage etc before getting into more invoved work

Jun 05, 2017 | Dodge Cars & Trucks

1 Answer

WONT START WHEN COLD CRANKS FINE. HAS CODE 54 CAM


ok, any obd code means the sensor concerned is not detected by the ecu, or is way out of range of the normal signal the ecu expects. I would therefor check the electrical path between the sensor and the ecu terminals, it may be just a chafed cable or wire.

Jan 14, 2010 | 1997 Dodge Caravan

4 Answers

I have a 2000 dodge durango, I have a code P0320.


I put in a new crank positioning sensor and it fixed my problem. 42.00 dollars from NAPA. took about 2 hours to change it.

Mar 09, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
2010 Dodge Challenger Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...