Question about Suzuki Grand Vitara

Open Question

Remove a/c vents - Grand Vitara Suzuki Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Vapor Canister Vent Solenoid located on a 2003 Chevy Silverado 1500, 4.3L engine? And do you ave to remove the pick-up bed to access it, if it is on top of the tank?


No you don't have to remove the pick up bed to get at it. It's on the left frame rail along side of fuel tank !
Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister vent electrical connector, if equipped. Disengage the 2 vent valve pipe clips securing the pipe to the underbody.
Remove the clips from the underbody and discard.
Disconnect the vent valve pipe at the EVAP canister. Remove and retain the EVAP canister vent valve bracket mounting bolt. Remove the complete EVAP canister vent valve assembly with bracket attached and discard.
Notice: Refer to Fastener Notice in the Preface section.
Video on youtube !

Dec 31, 2015 | Cars & Trucks

1 Answer

How do i replace a heater core in my 97 blazer


Heater Core Removal & Installation To Remove:
Heater core removal gm-10-00-651.gif

  1. Remove the heater/vent module.
  2. Remove the heater core access cover screws.
  3. Remove the heater core access cover.
  4. Remove the heater core from the heater/vent module
To Install:
  1. Install the heater core to the heater/vent module.
  2. Install the heater core access cover and screws to the heater/vent module.
  3. Install the heater/vent module assembly to the vehicle.
prev.gif next.gif

Dec 19, 2010 | 1997 Chevrolet Blazer

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

1 Answer

Heater core replacement


Heater Core Removal & Installation To Remove:
Heater core removal gm-10-00-651.gif

  1. Remove the heater/vent module.
  2. Remove the heater core access cover screws.
  3. Remove the heater core access cover.
  4. Remove the heater core from the heater/vent module
To Install:
  1. Install the heater core to the heater/vent module.
  2. Install the heater core access cover and screws to the heater/vent module.
  3. Install the heater/vent module assembly to the vehicle.
prev.gif next.gif

Oct 08, 2010 | 2003 Chevrolet Blazer

1 Answer

We accidently had the door shut on my friends 95 fork truck, and the keys were still in ignition. We had to break the ventglass window, how do we replace that? window


1st. Remove door trim panel by removing the screw retaining the armrest section of the trim panel to the door inner panel and remove armrest.
2nd. Remove the screw retaining inside door handle and remove the handle.
3rd. On vehicles with manual operated window cranks remove the screws retaining the crank, then remove the crank and washer.
4.th On vehicles with power windows, remove the power window switch panel by inserting a thin blade screwdriver between the bezel abd the trim panel, at either side of the bezel. Then carefully pry the bezel from the trim panel and the housing assembly will snap out. Remove the retaining screws from the bottom side of the connector and remove the switch assembly from the connector.
5th Remove door lock control knob on models rquiped with.
6th On models with power door locks, remove the switch housing assembly from the panel by inserting thin blade screwdriver into the spring tab slot located at the top and bottom of the switch housing. Apply pressure and the assembly will pop out. Disconnect the housing from the wirring assembly connector by separating the lock fingers.
7th. If equipped with power outside rear view mirror, remove the switch housing bezel by removing the two retaining bezel nuts and the bezel.
8th. Remove the screw retaining division bar to inner door panel.
9th.Remove the screws retaining vent window assembly to the leading edge of the door.
10th. Lower the door glass to the bottom of its travel.
11th. Pull the glass run out of the upper run retainer next to the vent window division bar. Pull the glass run out just far enough to allow the vent window assembly to be removed.
12th Tilt the vent window and the division bar assembly toward rear of the door. Carefully guide the assembly up and out of the door.
13th. Remove the two upper pivot-to-vent frame screws.
14th. Remove the retaining nut and tension spring from the vent vindow lower oivot.
15. Separate the vent glass retainer and the pivot stops from the vent frame and weatherstripping assembly.
16th. Installation is reverse of the removal procedure. The pivot tension spring should be adjusted so the vent will remain open at higway speeds. Be sure the front door window spacer is in place when installing the vent window and division bar assembly.

I know it is hard to picture it but this is best I can explain with out picture.

Feb 23, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

93 sts upper dashpad removal


remove the vents with a flat head screw driver. use a 7mm socket to remove 1 bolt each vent . now thair are 3 screwes in the defrost vent remove them. remove the trim that covers the matal wher the windshild is thay just pop off it goes from the dash pad to the headliner u should know what im talking about. now be carfule and remove the sensor where the defrost cover is . and thats it

Jan 20, 2010 | 1994 Cadillac Seville

1 Answer

How do i remove dashboard clocks


Do not leave the instrument cluster face down for any length of time. Lower and extend the steering column to its maximum rearward position. Disconnect the battery ground cable. Remove the air vent. Release the tangs. Remove the air vent. Remove the air vent. Release the tangs. Remove the air vent. Remove the center air vents. Release the tangs. Remove the center air vents. Detach the switch assembly. Remove the switch assembly. Disconnect the electrical connector. Remove the instrument panel veneer trim retaining screw. Remove the instrument panel veneer trim retaining screws. Remove the instrument panel veneer trim retaining screws. Detach the instrument panel veneer trim. Remove the instrument panel veneer trim. Detach the instrument cluster. Remove the instrument cluster. Disconnect the electrical connectors. To install, reverse the removal procedure.

Jul 28, 2009 | 2002 Jaguar X-Type

1 Answer

Leak at bottom of water expansion tank on 2001 s-type se


SECTION 303-03: Engine Cooling 2001 Lincoln LS Workshop Manual REMOVAL AND INSTALLATION Degas Bottle Removal and Installation
  1. Drain the engine cooling system. For additional information, refer to Cooling System Draining, Filling And Bleeding in this section.
  1. Remove the cowl vent screen. For additional information, refer to Section 501-02 .
Cowl Vent Screen Removal
NOTE: To remove the left side cowl vent screen, the right cowl vent screen must be removed first. Follow the entire cowl vent screen procedure.
Right Side Only
  1. NOTE: The fasteners are reuseable.
    Remove the right side of the cowl vent screen.
    1. Remove the two-part pin-type retainers and separate the Velcro ® attachment of the rubber hinge cover to the rear outboard corner of the cowl vent screen.
    1. Pull up on the cowl vent screen to release the lower clips.
Entire Cowl Vent Screen
  1. Remove the two wiper pivot arms.
    1. Remove the two pivot arm nut covers.
    1. Remove the two nuts.
    1. Remove the two wiper pivot arms.
  1. NOTE: Remove the right side first when removing the entire cowl vent screen.
    Remove the cowl vent screen.
    1. Remove the two-part pin-type retainers and separate the Velcro® attachment of the rubber hinge cover to the rear outboard corner of the cowl vent screen.
    1. Lift up on the cowl vent screen to release the clips.
  1. Disconnect the engine vent hose, and separate the air bleed hose from the degas bottle.
  1. Remove the seven bolts and reposition the cross vehicle support.
  1. Disconnect the degas return hose from the degas return tube.
  1. Remove the two bolts.
  1. Remove the degas bottle from the vehicle.

Apr 12, 2009 | 2001 Jaguar S-Type

1 Answer

Cabin air filter


it;s under the cowl vent panel.

Cowl Top Vent Panel Removal
  1. Remove the windshield wiper pivot arm (17526) . Refer to Section 01-16 for the removal procedure.
  1. Remove the front door weatherstrip (20530) to access the windshield outside side moulding screws.
b981661.gif
  1. Remove the five windshield outside side moulding screws and the windshield outside side moulding (03136) .





  1. Pull the windshield outside moulding (03144) from the windshield glass (03100) .
  1. Remove the three Phillips-head screws from the cowl top vent panel (022A68) .


9bc8ed6.gif

  1. Remove the three plastic screws by turning them 90 degrees to unlock.





  1. Remove the six pushpins from the front edge of the cowl top vent panel .
  1. Lift up on the cowl top vent panel and disconnect the windshield washer hose (17A605) at the Y-connector.





  1. Remove the cowl top vent panel .

Mar 15, 2009 | 1998 Mercury Villager

1 Answer

Vent window repair.


To replace the window seal, you first have to remove the vent window assembly from the door. After it is removed, the nut and spring on the bottom of the window has to be removed. Then remove the glass and frame from the vent assembly frame. Then gently remove the rubber off of the frame and install the new one after you replace the top vent bar seals. Reverse the window removal procedures to reinstall the glass and frame. The top vent bar seals requires a special tool to remove and replace the rivets you get with the replacement seal. You need to replace the top vent bar seal before reinstalling the new vent window rubber. When I replaced my top vent seals, it was fairly easy with my removal/installation tool.

Oct 03, 2008 | 1965 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...