Question about 1994 Toyota Pickup

Open Question

Oil sending unit wire broke needs to be replaced

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 200 Answers

SOURCE: NO OIL PRESSURE READING ON DASH

remove sending unit and install mechanical gauge to see oil pressure psi if psi reads ok- change sending unit again if psi to low less then 6 replace oil pump och.

Posted on Sep 19, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to replace the oil sending unit on my 2008 Pontiac G6 as it is leaking oil, but am having trouble determining the right part #. Is there an oil sending switch AND a separate oil sending unit?


there should be a sender unit with one wire attached that is connected to the oil light or gauge and there possible is a oil pressure sensor switch with 2 or more wires attached that reports to the ECM unit that shuts the motor down when the oil pressure is insufficient
take it to a service center and have it identified

Sep 06, 2016 | 2008 Pontiac G6

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

Oil Gauge Marking Way Past 80


Check your dipstick for antifreeze in the oil. You mad need to replace the oil pressure sensor/sending unit. If there's no antifreeze in engine oil, replace sending unit. Should be a round silver sending unit at the left rear place on the intake with a plastic black wiring connector with 2-3 wires going into it.

Jan 25, 2013 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

Oil sending unit


Hi Steve,

You may or may not have an issue with the wire, as per your description...
BUT, most issues are the sending unit. They are replaced diagnostically. You need a special socket to replace it, so buy one at the parts store. This need not be a dealer item. anyways, 99% of the time the sender fails.

Oct 29, 2012 | Cars & Trucks

1 Answer

My oil light stays on at starting the pick up 4 cylinder


FIRST CHECK YOUR OIL LEVEL, IF OK YOU MAY HAVE A FAULTY SENDING UNIT OR BROKE SENDING UNIT WIRE, IF OK, CHECK FOR LOW OIL PREASURE

Jul 20, 2011 | 1993 Nissan Pickup

1 Answer

I recently had my angle gear ( also called transfer case) replaced in my 2004 volvo s60. After I picked up the car, the work seemed o.k., but them my stop engine light came on saying that I had no oil...


Well my best guess would be that in the process of repairing the angle gear they may have bumped and broke your oil sending unit. The angle gear has nothing to do with oil pressure but it is a big bulky part and a oil sending unit could be broke pretty easy while installing something like that. I would take it back to them and have then look at it to see if its broke and a good shop would fix it for free since they broke it.

Jan 06, 2011 | 2004 Volvo S60

1 Answer

Need help with oil pressure sending unit...maybe


You got it, Common for the plastic top where the wire leads connect to crack. This will cause the oil to leak and at worst, what you have indicated happening on your Blazer. Note; when installing the new sensor, do not use any Teflon tape on the threads. The sensor is tapered and works best to have a good ground, so just tighten it enough to keep the oil from leaking. Good luck friend and make sure you pick up the right oil sending unit sensor. One is for just a light to activate and the other is the one you need to be able to give you a oil pressure reading. Best to go at a Dealer for this part with your VIN number.

Jan 12, 2010 | 1998 Chevrolet Blazer

2 Answers

Volvo 850 oil pressure sending unit


It's on the engine, right next to the starter, it has one wire going to it. You don't need to drain the oil. If the light is coming on, you may have bad seals in the oil pan, a fairly common problem, but replacing the switch is a good fisrt step.

Jan 27, 2009 | 1995 Volvo 850

1 Answer

Thanks! and another question?


With the tranny flush, yes. It's possible that they may have knocked the connection loose or broke it at the sending unit. The unit is usually located on the side near the bottom ot the tranny. With the oil change I'm going to say no. The oil sending unit is generally located on the driver side, center of the engine block near or under the exhaust manifold, or on the front of the block towards the top. Unless they moved them on me, it shouldn't be anywhere close to the drain plug on the oil pan, and there no way that they should get near the oil sending unit when changing the oil, unless the sending unit is near the oil filter, and GMC generally doesn't put the two near each other for this reason. Just thought of something. Are the gages individually replaceable, or are they all built into one display unit?

Jul 30, 2008 | 2004 GMC Envoy

Not finding what you are looking for?
1994 Toyota Pickup Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...