Question about 2006 Chevrolet Malibu

Open Question

Removing a/c evaporater

Install a/c evaporator

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location ac evaporater vavle 2003 lexus es300


if you mean the expansion valve, is locate it at evaporator core, under the right side of dash.

Sep 29, 2014 | 2003 Lexus ES 300

1 Answer

Where is the air condition evaporater hose located on a 1992 Chevrolet S10 V6 pickup


AC evaporator is located within the heater box inside under the dash,the pressure lines are under the hood from either the compressor or the condenser.

May 05, 2014 | Cars & Trucks

1 Answer

Where is the evaporater drain hose located on a 1992 Chevrolet S10 V6 pickup


The drain hose is located on the evaporator case you can see it from under the car it is about in line with fender and door gap and inline with evap case.

May 05, 2014 | Cars & Trucks

1 Answer

Heater core removal 2000 mustang gt


The first thing your going to have to do is take it to a repair shop and have the air conditioning system discharged.Disconnect the battery and drain the cooling system.Disconnect the heater hoses at the firewall and also disconnect and plug the evaporator tubes at the firewall and also plug the heater core tubes so that you dont spill any coolant when you take it out.Cap the evaporator tubes so that you dont get any dirt or water in them.Next you want to remove the instrument panel.Then disconnect the main vacuum line from the heater/evaporater housing to the engine.This is located above the rear of the right valve cover.Then pull the hose through the firewall into the inside of the car.Remove the heater/evaporater housing screws which includes a bolt near the top center of the unit,a nut at the top righ,a bolt near the bottom,and a nut on the engine side of the firewal.Make sure that there are no other wires or hoses connected to the housing and then pull the heater/evaporater housing out from under the cowl and remove it from the vehicle.Take out the 4 screws and the heater core cover then you can take out the heater core.Be very carefull not to tear the foam sealing material.To install it reverse everything.hope that this will help a little.

Apr 10, 2011 | 2000 Ford Mustang

1 Answer

Need to replace heater core for Ford Taurus 2000


Heater and Evaporator Core Housing Removal & Installation To Remove:
  1. Recover the refrigerant.
  2. Remove the instrument panel.
  3. Remove the right side cowl vent screen.
  4. Remove the screws and the water shield.
  5. Disconnect the vacuum supply hose.
  6. Clamp off and disconnect the heater hoses at the firewall.
  7. Disconnect the evaporator outlet spring lock coupling. Discard the O-rings.
  8. Remove the two condenser-to-evaporator line bracket bolts.
  9. Disconnect the evaporator inlet spring lock coupling. Discard the O-rings.
  10. Remove the three nuts at the dash panel.
  11. Remove the screws and the heater outlet floor duct.
  12. Remove the evaporator core housing bolt and nut.
  13. Remove the heater and evaporator core housing.
Heater and evaporator core housing removal/installation ford-10-00-404.gif

To Install:
  1. Install the heater and evaporator core housing in the vehicle. Secure the mounting nut and bolt.
  2. Install the heater outlet floor duct. Secure with the mounting screws.
  3. Install the three mounting nuts to the dash panel. Tighten to 53 in-lb (6 Nm).
  4. Install new refrigerant system O-ring seals lubricated in clean mineral oil. Connect the evaporator lines.
  5. Install the two condenser-to-evaporator line bracket bolts. Tighten to 80 in-lb (9 Nm).
  6. Connect the hoses to the heater core connections. Lubricate the coolant hoses with plain water only, if needed.
  7. Connect the vacuum supply hose.
  8. Install the screws and the water shield.
  9. Install the right side cowl vent screen.
  10. Install the instrument panel.
  11. Lubricate the refrigerant system with the correct amount of clean PAG oil.
  12. Evacuate, leak test and charge the A/C system.
  13. Add coolant as needed.
prev.gif next.gif

Jan 08, 2011 | 2000 Ford Taurus

1 Answer

Change evaporator 1996 cheve truck 1500 350


Removal & Installation To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the coolant from the engine.
  3. Recover the refrigerant.
  4. Remove the glove compartment.
  5. Remove the floor air outlet.
  6. If equipped with a diesel engine, remove the powertrain control module.
  7. Remove the kick panel trim.
  8. Remove the blower motor.
  9. Remove the steering column.
  10. Tilt back the instrument panel assembly.
  11. Remove the coolant recovery reservoir from the engine compartment.
  12. Disconnect the heater hoses and the evaporator tube.
  13. Remove the accumulator.
  14. Remove the fasteners and the HVAC module assembly.
  15. Remove the cover plate on the bottom of the HVAC module.
  16. Remove the heater core and seal from the HVAC module.
  17. Remove the case cover from the HVAC module.
  18. Remove the evaporator core.
HVAC module mounting fastener locations gm-10-00-1003.gif

HVAC module components gm-10-00-1004.gif

To Install:
NOTE: If a new evaporator is being installed, add 3 fl oz (90 ml) of refrigerant oil to the new evaporator.
  1. Install the evaporator core.
  2. Install the case cover.
  3. Install the heater core and the seal.
  4. Install the cover plate on the bottom of the evaporator case to the HVAC module.
  5. Install the HVAC module in the vehicle.
  6. Install the accumulator.
  7. Connect the evaporator tube and heater hoses.
  8. Install the coolant recovery reservoir.
  9. Install the instrument panel.
  10. Install the steering column.
  11. Install the blower motor and cover.
  12. Install the kick panel trim.
  13. Install the powertrain control module and tray.
  14. Install the floor air outlet.
  15. Add coolant to the cooling system.
  16. Connect the negative battery cable.
  17. Evacuate and charge the A/C system.
  18. Check the system for leaks.
prev.gif next.gif

Aug 14, 2010 | 1996 Chevrolet C1500

1 Answer

Honda pilot will not start after being in hot sun


fuel evaporation it can be caused by someone working at the engine and not replacing the heat evaporation shield its sometimes looks like heavy tinfoilit sits around the fuel intake,and if missing the heat of the engine/sun evaporatates the fuel in the system check it out.adrian,,,,,,

Aug 12, 2010 | 2007 Honda Pilot

2 Answers

How do you replace the evaporator core for the a/c? on a 1994 gmc p/u truck, I've already have the dash out having promblems removing the duct work, what's next? or is there a maunal that will show me.


your instructions are on how to replace the condenser on a 1994 gmc sierra but the title says it is the directions for replacing an evaporator. please correct your title.

Aug 08, 2010 | 1994 GMC Sierra

1 Answer

My jeep passenger floor stays wet. could it be the heater core or the evaporater core?


I would think the drain hose for the evaporator core has come off or is clogged. If it was the heater core, you would smell anti-freeze and there would be some steam asscociated with it.

May 16, 2010 | 1998 Jeep Grand Cherokee

1 Answer

Check engine light on, engine running rough


evaporator is part of the fuel system, missfiring could be spark plug or bad coil

Mar 26, 2009 | 2001 Mercury Cougar

Not finding what you are looking for?
2006 Chevrolet Malibu Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...