Question about 1989 Nissan Hardbody King

Open Question

Distributor diagram need to locate number one terminal on dist. cap 24zi motor

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy 350 firing order diagrams


1-8-4-3-6-5-7-2

TDC on #1 compression stroke,not exhaust

Number 1 on the dist cap-- is at about 7 o clock,
as you face the motor from the front

2-4-6-8
1-3-5-7

1&2 are at the front-- as you face it

Sep 14, 2013 | Cars & Trucks

2 Answers

When i bolt on the new distributor on a 1995 caprice lt1 4.3 is there away it has to be done like set to number like you do with the old style everybody keeps telling me no but it just doesnt make sense to...


You would put the distributor back in so that the rotor points to the same terminal on the cap the old distributor was pointing to.
If the shaft of the distributor has a notch, you can only put it in two ways with the rotor pointing to two terminals.
If you did not set the crankshaft to TDC before you removed the old dist, you have a 50 percent chance of being in the right position.
The notch on the bottom of the dist keeps you from picking any position other than the right one and the one 180 degrees off.

Aug 21, 2012 | 1995 Chevrolet Caprice Classic

1 Answer

Need a wiring diagram for spark plugs for a 1995 jeep Cherokee sport


V6 engine: firing order: 1 2 3 4 5 6, distributor rotates clockwise. Left bank of engine (driver's side), cylinders 2, 4, 6 (#2 at front of engine). Right bank: 1, 3, 5 (#1 at front of engine).
Inline 6 engine: firing order is 1-5-3-6-2-4. Distributor rotates clockwise.
The number one tower on the dist. cap should have a mark or numeral 1 on it. If not, turn crankshaft to top dead center of compression stroke on number one cylinder, the 0 degrees or "T" mark on the crank pulley pointer. If you are on the compression stroke (not the exhaust stroke), the rotor under the dist. cap will be pointing to the number one cylinder spark plug wire tower.

Mar 30, 2012 | 1995 Jeep Cherokee

3 Answers

I changed the spark plugs and wires on my chevy s10 2wd pick up, which is a 4 cylinder and now it will not turn over. I might have the wires mixed up on the distributer cap. Can someone show me a picture...


GET A PIECE PAPER DRAW A LARGE CIRCLE TOP UPPER HALF CIRCLE LEFT TO RIGHT WRITE NUMBERS 1 AND 3 BOTTOM HALF CIRCLE LEFT TO RIGHT RIGHT NUMBERS 2 AND 4 THAT YOUR DISTRIBUTOR SPARK PLUGS WIRES LOCATION.STANDING ON SIDE OF ENGINE WHERE DISTRIBUTOR IS LOOKING DOWN AT DISTRIBUTOR 1 AND 3 FIRST TWO SPARK PLUGS TERMINALS NEXT TO ENGINE. AND 2 AND 4 SPARK PLUGS TERMINAL ON CAP FACING YOU. THIS IS CYLINDERS LOCATIONS STANDING IN FRONT OF ENGINE.RUN WIRES FROM DISTRIBUTOR CAP TO PLUGS TO THE ENGINE SPARK PLUGS.

Oct 17, 2010 | Chevrolet S 10 Cars & Trucks

3 Answers

Location of spark plug wires to distributor cap for jeep cherokee 4.0 1987


Here is a firing order diagram for that vehicle and engine, and let me know if you need any help to understand this diagram, or if you require any further assistance.


f833d4b.jpg

Sep 28, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

I need the exact diagram for my V6 firing order and where is number one on the distributor?


153624 is the firing order ,i have no idea where no1 is on the distributor cap ,what i would do is assume that no1 is front left ,take the rocker cover off and watch the valves ,when the inlet and exhaust valves are both open at the same time look to dist cap and it will be pointing at this cylinder so take that as no1 and see if it runs .Sorry we only use mainly 4 cyl engines here in spain as we cannot afford the petrol for bigger motors ,

Jun 15, 2010 | Cars & Trucks

1 Answer

Need ignition wiring diagram for 93 z71


It's like a phone number. 1-843-6572 Clockwise rotation of distributor. Number one should be indicated on the dist. cap.cylinders are pass side 1357, drivers side 2468
If #1 is not printed on the cap it is around the 5:30-6:00 position. Unless you are refering to the primary ignition wiring then you can just hop on Autozone and get the wiring diagram from them for free.

Jul 31, 2009 | 1993 Chevrolet K1500

1 Answer

Need wireing diagram to change 72 nova over to hei distributor


Hey , just take the positive wire from the coil you are removing and feed it to the + terminal on the HEI dist. cap.the other terminal under there is for your tachometer. If you are mounting a master kill switch in the bumper for drag racing- attatch the kill wire to the tach terminal also.
Thats it you just plug the three wire pigtail from the dist. base(pickup) to the cap and you are off.
Remember firing order is 18436572 in a clockwise direction. to find #1 remove #1 plug and have someone"bump" the engine over while holding your finger over the hole-carefull. then line up the slotted mark on the crank pulley with the big notch on the timing indicator. Good luck

Aug 31, 2008 | Chevrolet Chevy Cars & Trucks

1 Answer

1995 Ford F350 5spd. distributor cap wiring diagram/layout!!!


1) #1-4 pass side front to rear #5-8 drivers side front to rear
2) 1-3-7-2-6-5-4-8
3)#1 is usually marked on cap wires go ccw
4) TDC #1 cyl you must remove the shorting plug before timing
it is located by the dist plug or the ignition module small gray plug

Jul 17, 2008 | 1995 Ford F350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...