Question about 1998 Ford Taurus

1 Answer

Panel that goes under ford taurus engine what does it screw into

The panel that goes under the front of the engine on a 1998 ford taurus was removed and i don't know what it screws back into

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 64 Answers

Take a look at the panel and you will see where the holes for screws are, when you line it with where it is suppose to go the holes will be where it screws.

Posted on Apr 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jaykhjr
  • 3 Answers

SOURCE: replacing rear speakers on 1998 ford taurus

i had a 93 tarus for awhile and i dropped some pioneers in it. it was easy because the speakers actually sat on top of the paneling but on a 98 they are under it. the easiest way to go about changing them is to remove them from the top of the trunk. the fabric unclips from the top and a few screws hold the speakers in place.

Posted on Jun 28, 2009

  • 1986 Answers

SOURCE: Adjust (aim) headlights on a 1990 Ford Taurus

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Nov 04, 2009

wfservices
  • 260 Answers

SOURCE: alternator removal 1998 ford taurus dohc

3.0L (4V)
Removal

  1. Disconnect the battery ground cable.
  1. Remove the accessory drive belt from the generator pulley.
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist.
  1. Remove the right front wheel.
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.

Posted on Mar 14, 2010

  • 1 Answer

SOURCE: how do you remove the stereo from a 1998 ford taurus

A special tool is not needed. You can cut 2 pieces of coat hanger and bend them into a U and they work the same as the special tool

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove ford taurus window switch


Door Panels

Print


REMOVAL & INSTALLATION

See Figures 1 through 8
This procedure applies to both the front and rear door panels.


0900c152802604e4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Remove the cover from behind the inside door handle by gently pulling it out to release the retaining tabs


0900c152802604e5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Remove the pull cup retaining screw cover and...


0900c152802604e6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: ... remove the retaining screw from the cup and lift the cup straight up out of the door panel


0900c152802604e7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Remove the two sail panel/speaker grille retaining screws and...


0900c1528026022f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: ... remove the panel/grille from the door


0900c152802604e8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: The door panel is retained to the door by 11 retaining clips


0900c152802604e9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Carefully lift the door panel off of the door and...


0900c152802604ea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: ... detach the electrical connectors from the switches and remove the panel from the vehicle

  1. Remove the cover behind the inside door handle.
  2. Remove the screw from the bottom of the pull cup retaining the front door trim panel to the front door.
  3. Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door.
  4. Remove the three screws retaining the front door trim panel to the front door.

Do not attempt to remove more than one pushpin at a time.
  1. Use a suitable tool to remove the pushpins from the door.
  2. Carefully lift the door panel away from the door.
  3. Detach the electrical connectors as necessary and remove the panel from the door.

To install:
  1. Installation is the reverse of removal.

Aug 15, 2012 | 1998 Ford Taurus

1 Answer

Four way flashers and signal lights are not working on 1998 for taurus have changed the delay relay switch


Replace the flasher unit. The flasher/turn signal is screwed into the metal support above the fuse panel, you must take the bottom of the dash off and remove the plastic cover. this is for a sable that has light out detection.
Look under your dash for a blue box screwed into the right side of the dash panel. This of course is done, with you laying on your back, and your feet in the back seat.

It's a blue box, about the size of half a twinkie (cream filled, golden sponge cake).

Remove the plug that holds it in, unscrew the screw that holds it to the frame, and go to Autozone or other parts store, to get a new relay.

You will have to reuse the metal piece that holds the relay to the dash panel, so be sure and save that before you throw the old part away.

Installation is the reverse.

May 08, 2011 | 1998 Ford Taurus

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

Where is the pcm on a 1999 ford taurus


The PCM is located behind the engine on the passenger side of the car, it is in a slot in the fire wall behind the cowl cover. here is Fords instructions for replacing it.Powertrain Control Module (PCM)
Removal

Disconnect battery ground cable (14301) . Refer to Section 14-01.

Remove cowl deflector.

Remove screw securing the ground cable of the engine control sensor wiring (12A581) to the dash panel (01610) .

Loosen engine control sensor wiring to PCM connector retainer bolt.

Remove engine control sensor wiring from PCM (12A650) .

Remove retaining nuts and powertrain control module insulator from dash panel .

Remove powertrain control module .

Installation

Follow removal procedure in reverse order.

Tighten insulator retaining nuts to 8-12 Nm (71-106 lb-in).

Tighten engine control sensor wiring retainer bolt to 3.7 Nm (33 lb-in).

Tighten engine control sensor wiring ground retaining screw securely.




shortgap.png

Dec 28, 2010 | 1999 Ford Taurus

1 Answer

How to remove right front panel on 2000 ford


This is for the front passenger side door panel from a 1999 Ford Expedition. The driver's side door should be the same, except for the mirror switch which needs to be unplugged. The 1998 *might* be the same, I don't know, but this should be helpful to someone.

Use a flat blade screwdriver or other suitable tool to pry out on the top of the triangular plastic panel on the top front of the door panel. The plastic holder should pull out of the door. Now pry up on both sides of the triangular panel and pull it loose. Remove the philips head screw you find under this panel. Pull the door latch handle, pry out the insert where the handle goes through, and remove the bolt that holds the door handle in place. Remove the door handle. Pry up on the ends of the door switch panel to remove it. Unplug the cables by pushing in on the lock tab on the side of the plug and pulling out. Remove the philips head screw accessible through the switch panel hole. Insert a flat blade screwdriver into the slot at the bottom of the courtesy light lens and pry up and out to remove the lens. Remove the philips head screw behind this lens. Pull up on the door panel to remove it. Be careful of the courtesy light when removing the panel - give the light a quarter turn counter-clockwise from the rear to remove it from the door panel.

Its possible that this GUIDE can helpfull as reference.

Hope this help.

Apr 22, 2010 | 2000 Ford Expedition

2 Answers

Where is the DRL module on a 99 ford taurus


The module for my Daytime running lights for 99 Ford Taurus is behind or kind of under the drivers side headlight. Pretty much behind the bumper.

Nov 13, 2009 | 1998 Ford Taurus

1 Answer

1998 ford taurus instrument lights - it appears that the whole dash front needs to come off in order to access the 4th screw above the heater/radio panel. Do you need a special tool to remove the radio...


you can used a cut coat hanger bent into 2 u shaped
tools stick them into the 4 holes and squeeze them together and pull out on the radio should come out

Nov 12, 2009 | 1998 Ford Taurus

1 Answer

Replacing rear speakers on 1998 ford taurus


i had a 93 tarus for awhile and i dropped some pioneers in it. it was easy because the speakers actually sat on top of the paneling but on a 98 they are under it. the easiest way to go about changing them is to remove them from the top of the trunk. the fabric unclips from the top and a few screws hold the speakers in place.

Jun 28, 2009 | 1998 Ford Taurus

1 Answer

Replacing window motor


Start by disconnecting your negative battery cable. Then you need to locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Once you remove the screws that hold the door handles, remove any wire connectors to the handles. The door panel itself, is held on by snap in clips, and you will need a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are removed from the door, pull the panel upward to remove it from the door. Once you gain access to the interior of the door, you will need to remove the motor and regulator as a single unit. Once you have removed the regulator you will be able to replace the motor.

Install in reverse.

I hope this helps you, and I wish you luck on your repair

May 10, 2009 | 1998 Ford Taurus

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

Not finding what you are looking for?
1998 Ford Taurus Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...