Question about 2011 Chevrolet Aveo

Open Question

Aveo caliper mounting bolts torque - 2011 Chevrolet Aveo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 33 Answers

SOURCE: Need the correct torque specs for 2004 silverado 1500 calipers

  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Posted on Mar 28, 2009

    Ad
    • 72 Answers

    SOURCE: Front Hub Bearing Torque specs to complete replacement

    THE LUG NUT TORQUE SPEC - 140FT/LBS\
    CALIPER MOUNT - 80FT/LBS
    CALIPER BRACKET 129FT/LBS
    AXLE NUT 177FT/LBS

    Posted on May 09, 2009

    dennymulford
    • 1055 Answers

    SOURCE: allen wrench size to fit caliper mounting bolt

    some are 7/16 and some are 3/8 amd some are torx

    Posted on May 30, 2009

    • 333 Answers

    SOURCE: Replacing front wheel hub assembly on 2006

    Caliper mount bolts are 74 ft/lbs
    Driveshaft axle nut is 177 ft/lbs
    Hub and bearing mounting bolts are 133 ft/lbs

    Posted on Sep 10, 2009

    Testimonial: "The info on the torgue specs was very helpful. I couldn't find it anywhere. Thanks a bunch!"

    • 20 Answers

    SOURCE: 2004 chevy aveo cylinder head bolt torque how many

    Step 1: 18 lb.-ft.
    Step 2: additional 60 degrees.
    Step 3: additional 60 degrees.
    Step 4: additional 60 degrees.
    Step 5: additional 10 degrees.

    Each step involves starting at the center two bolts of the head and alternately tightening in a criss-cross pattern, ending with the bolts on the outer edge of the head.

    Posted on Sep 14, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    What is the torque specs for brake calipers on a ford explorer sport front calipers


    1. Torque Specs For F250 Caliper Bolts - Diesel Forum - TheDieselStop.com

      www.thedieselstop.com > ... > 1999-2007 General Questions Jan 13, 2009 - 3 posts - ‎1 author
      Does any one know what the caliper bolts torque specs are? ... Disc brake caliper pin bolts - Excursion, F-250/F-350 with Ford and Dana axle ... Torque specs for front brakes
      5 posts
      Mar 12, 2009
      05 F250 brake torque specs please
      6 posts
      Aug 22, 2007
      Brake caliper torque specs
      5 posts
      Jul 14, 2007
      Front brake Caliper Bolt Torque
      6 posts
      Apr 25, 2005
      More results from www.thedieselstop.com

    Jul 11, 2015 | 1998 Ford Explorer

    1 Answer

    Caliper bolts get loose


    the main mounting bolts? not guides?
    caliper mount to knuckle bolts?
    what torque did you use? in foot/lbs.

    1. id bet they are not factory spec bolts
    2. or you used the wrong torque page.
    3. or your tool is no good. (harbor fright tools?)
    use a beam torque tool, it will never fib to you, like cheap clickers do.
    I promise.
    specs
    tighten the caliper pin bolts to 26 ft. lbs. (36 Nm). Bottom bolt
    there are 4 bolts specs here.
    above pin
    banjo 17ft/lbs
    top B bolts is 61.5 foot lbs. (this came loose at 61 ?)
    C spec is 5ft/lbs on bleeder nipples.

    now alternator tack.
    the rotor is warped so bad it bead the calipers to death.
    the wheel bearing, is so bad , same.

    ever check those for run out, and end play?
    bingo if true.
    damage and collateral damage are limitless.
    and rust too. (entropy of all kinds)

    Apr 16, 2014 | 2010 Suzuki Grand Vitara

    1 Answer

    Front caliper bolts torque


    1. Remove or disconnect the following:

      Wheel Brake hose from the caliper Caliper mounting bolts Caliper
    To install:

    1. Install or connect the following:

      CaliperCaliper mounting bolts and tighten to 58-73 ft. lbs. (80-100 Nm) on the front caliper, or 37-44 ft. lbs. 50-60 Nm) on the rear caliper.Brake hose to the caliper and tighten the fitting too 18-22 ft. lbs. (25-30 Nm)Wheel
    2. Bleed the brake system.

    Sep 23, 2013 | 2004 Hyundai Santa Fe

    1 Answer

    2004 chevy malibu classic caliper torque


    caliper mounting bracket bolts torque 85 ft lbs torque caliper bolts 26 ft lbs..

    Jul 06, 2013 | Cars & Trucks

    2 Answers

    How to change brake pad and check rotors


    Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

    To Remove:
    1. Drain brake fluid to ½ full level in reservoir.
    2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

    3. Remove the front brake caliper assembly.
    4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
    5. Remove the wear indicator from each of the 2 brake pads.
    To Install:
    NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
    toy_car_cam_frontbrakepads.gif

    1. Using a large C clamp or equivalent press piston into the caliper.
    2. Apply disc brake grease to the inside of each anti-squeal shim.
    3. Install the anti-squeal shims on each pad.
    4. Install the pad wear indicator clip to the pads.
    5. Install the pads with the pad wear indicator plate facing upward.
    6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
    7. Install the front wheels.
    8. Fill the master cylinder with new clean brake fluid.
    9. Pump the brake pedal several times to seat the brake pads.
    Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

    TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

    To Remove:
    1. Drain the brake fluid to ½ full level in reservoir.
    2. Remove the rear wheels.
    3. Remove the caliper slide pins.
    4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
    5. Remove the rear brake calipers.
    6. Remove the 2 brake pads with the anti-squeal shims.
    7. Remove the anti-squeal shims and pad wear indicators from brake pads.
    To Install:
    1. Using a large C clamp or equivalent press the piston into the caliper.
    2. Coat both sides of the outer anti-squeal shim with pad grease.
    3. Install anti-squeal shims to each pad.
    4. Install wear indicators on the 2 brake pads.
    5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
    6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
      • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
      • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
    7. Fill the master cylinder with new clean brake fluid.
    8. Pump the brake pedal several times to seat the brake pads.
    9. Install the rear wheels.
    prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
    1. Remove the front wheels.
    2. Remove the front brake caliper assembly.
    3. Remove the front brake pads.
    4. Remove the 2 bolts and caliper mounting bracket.
    5. Place match marks on the disc and axle hub.
    6. Remove the front wheel disc.
    To Install:
    1. Align the match marks and install the front disc.
    2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
    3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
    4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
    5. Fill the reservoir with brake fluid.
    6. Bleed the brake system.
    7. Install the front wheel.
    Rear To Remove:
    1. Remove the rear wheels.
    2. Remove the brake caliper assembly.
    3. Remove the brake pads.
    4. Remove the 2 bolts and the caliper mounting bracket.
    5. Place match marks on the disc and axle hub.
    6. Remove the rear disc.
    To Install:
    1. Align the match marks and install the rear disc.
    2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
      • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
      • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
    3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
      • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
      • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
    4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
    5. Fill the reservoir with brake fluid.
    6. Bleed the brake system.
    7. Install the rear wheel
    prev.gif next.gif

    Jan 25, 2011 | 2007 Toyota Camry

    2 Answers

    Brake job torque spec


    Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

    Nov 13, 2009 | 2005 Honda Civic

    1 Answer

    How to replace the front brake pads


      Calipers With Guide Pins
    1. Step 1 Disconnect the negative battery cable from the battery. Remove the wheel. Using an open wrench hold the lower guide pin. Remove the bolt that secures the caliper.
    2. Step 2 Pivot the caliper up and then suspend it from the frame using mechanic's wire. To remove the pads, slide the pads straight out.
    3. Step 3 Using a C-clamp, compress the caliper piston into the bore. Insert the new pads by removing the mechanics wire and pivoting the caliper back into it's place.
    4. Step 4 Clean the old bolt and apply thread locking compound. If the old bolt can not be used install a new bolt. Hold the guide pin using a back-up wrench when tightening the bolt. Using a torque wrench, torque the bolt to 26 foot/pounds. Install the wheels. Add oil to the master cylinder reservoir. Reconnect the negative battery cable to the battery.
      Calipers With Sleeves and Bushings
    5. Step 1 Disconnect the negative battery cable from the battery. Remove the wheel. Remove the bolt that secures the caliper to the carrier.
    6. Step 2 Push the caliper up and pivot the caliper bottom out of the carrier. Remove the pads and the anti-rattle springs.
    7. Step 3 Install the new pads by putting the anti-squeal pads onto the caliper and then sliding the new pads onto the carrier. Put the caliper top back into place. Remove the mechanics wire and push the caliper up so that it pivots back into place and the bottom.
    8. Step 4 Clean the caliper mounting bolts. Install the caliper mounting bolts and using a torque wrench, torque the bolts to 18 foot/pounds. Install the wheel. Add oil to the master cylinder reservoir. Reconnect the negative battery cable to the battery.

    Jul 09, 2009 | 2006 Volkswagen Jetta

    2 Answers

    Front Hub Bearing Torque specs to complete replacement


    THE LUG NUT TORQUE SPEC - 140FT/LBS\
    CALIPER MOUNT - 80FT/LBS
    CALIPER BRACKET 129FT/LBS
    AXLE NUT 177FT/LBS

    Apr 24, 2009 | 2003 Chevrolet Silverado 1500

    1 Answer

    Need the correct torque specs for 2004 silverado 1500 calipers


  • Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft. lbs.) . Caliper Mounting Bracket to Knuckle, Front (15 series) 175 Nm (129 ft. lbs.) Caliper Mounting Bracket to Knuckle, Front (25/35 series) 300 Nm (221 ft. lbs.) Brake Caliper Mounting Bolt Rear (15 series) 42 Nm (31 ft. lbs.) Brake Caliper Mounting Bolt Rear (25/35 series) 108 Nm (80 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JC5/JH5) 200 Nm (148 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH6) 165 Nm (122 ft. lbs.) Caliper Mounting Bracket Bolt Rear (JH7) 300 Nm (221 ft. lbs.) Caliper Mounting Bracket Bolt Rear (NYS) 200 Nm (148 ft. lbs.)
    hope this helps
  • Mar 28, 2009 | 2004 Chevrolet Silverado

    4 Answers

    Torque specs for the cylinder head


    2004 ENGINE
    Engine Mechanical - 1.6L (L91) - Aveo
    SPECIFICATIONS
    FASTENER TIGHTENING SPECIFICATIONS
    Fastener Tightening Specifications
    Application
    Specification
    Metric English
    A/C Compressor Mounting Bolts 27 N.m 20 lb ft
    A/C Compressor Mounting Bracket Bolts 50 N.m 37 lb ft
    Air Filter Housing Bolts 12 N.m 106 lb in
    Alternator Adjusting Bolt 20 N.m 15 lb ft
    Alternator Adjusting Bracket Retaining Bolt 20 N.m 15 lb ft
    Auxiliary Catalytic Converter-to-Exhaust Manifold
    Nuts and Bracket Bolts
    40 N.m 30 lb ft
    Camshaft Cap Bolts 16 N.m 12 lb ft
    Camshaft Gear Bolt 67.5 N.m 49 lb ft
    Camshaft Pressure Plate Bolts 10 N.m 89 lb in
    Connecting Rod Bearing Cap Bolts 25 N.m+30°+15° 18 lb ft+30°+15°
    Coolant Pump Retaining Bolts 10 N.m 89 lb in
    Coolant Temperature Sensor 20 N.m 15 lb ft
    Crankshaft Bearing Cap Bolts 50 N.m+45°+15° 37 lb ft+45°+15°
    Crankshaft Position Sensor Retaining Bolt 10 N.m 89 lb in
    Crankshaft Pulley Bolt 95 N.m+30°+15° 70 lb ft+30°+15°
    Cylinder Head Bolts - Camshaft Support Housing
    and Cylinder Head Mounting Bolts
    25 N.m+60°+60°
    +60°+15°
    18 lb ft+60°+60°
    +60°+10°
    Electronic Ignition System Ignition Coil Mounting
    Bolts
    10 N.m 89 lb in
    Electronic Ignition System Ignition Coil Mounting
    Plate Bolts 10 N.m 89 lb in
    Engine Mount Bracket Retaining Bolt 65 N.m 48 lb ft
    Engine Mount Bracket-to-Engine Mount Retaining
    Bolts
    60 N.m 44 lb ft
    Engine Mount Retaining Nuts 40 N.m 30 lb ft
    Exhaust Flexible Pipe Bracket Bolts 40 N.m 30 lb ft
    Exhaust Gas Recirculation Valve Adapter Bolts 25 N.m 18 lb ft
    Exhaust Manifold Heat Shield Bolts 15 N.m 11 lb ft
    Exhaust Manifold Nuts 25 N.m 18 lb ft
    Flexible Plate Bolts 60 N.m 44 lb ft
    Flexible Plate Inspection Cover Bolts 10 N.m 89 lb in
    Flywheel Bolts 35 N.m+30°+15° 26 lb ft+30°+15°
    Flywheel Inspection Cover Bolts 12 N.m 106 lb in
    Front Muffler-to-Main Catalytic Converter Nuts 30 N.m 22 lb ft
    Fuel Rail Retaining Bolts 25 N.m 18 lb ft
    MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 1 of 330
    http://www.eautorepair.net/app/PrintItems.asp?S0=2097152&S1=0&SG=%7BEEDCF... 3/30/2009
    ENGINE MECHANICAL SPECIFICATIONS
    Engine Mechanical Specifications
    Intake Manifold Retaining Nuts 25 N.m 18 lb ft
    Intake Manifold Support Bracket Lower Bolt-to-
    Engine Block 40 N.m 30 lb ft
    Intake Manifold Support Bracket Upper Bolts 25 N.m 18 lb ft
    Lower Timing Belt Cover Bolts 10 N.m 89 lb in
    Oil Pan Retaining Bolts 10 N.m 89 lb in
    Oil Pressure Switch 40 N.m 30 lb ft
    Oil Pump Retaining Bolts 10 N.m 89 lb in
    Oil Pump/Pickup Tube and Support Bracket Bolts 10 N.m 89 lb in
    Oil Pump Safety Relief Valve Bolt 36 N.m 22 lb ft
    Oil Pump Rear Cover Bolts 6 N.m 53 lb in
    Power Steering Pump Mounting Bolts 25 N.m 18 lb ft
    Power Steering Pump Pulley Bolts 25 N.m 18 lb ft
    Rear Timing Belt Cover Bolts 10 N.m 89 lb in
    Spark Plug Cover Bolts 3 N.m 27 lb in
    Spark Plugs 25 N.m 18 lb ft
    Thermostat Housing Mounting Bolts 20 N.m 15 lb ft
    Throttle Cable Bracket Bolts 8 N.m 71 lb in
    Timing Belt Automatic Tensioner Bolt 25 N.m 18 lb ft
    Timing Belt Idler Pulley Bolt 40 N.m 30 lb in
    Transaxle Bell Housing Bolts 75 N.m 55 lb ft
    Transaxle Brace Bolts 40 N.m 30 lb ft
    Transaxle Torque Converter Bolts 65 N.m 48 lb ft
    Upper Timing Belt Cover Bolts 10 N.m 89 lb in
    Valve Cover Bolts 10 N.m 89 lb in
    Application
    Specification
    Metric English
    General Data
     Engine Type 4 Cylinder - In-Line
     Displacement 1598 cm3 97.51 in3
     Bore Stroke 79.0x81.5 mm 3.1x3.21 in
     Compression Ratio 9.5:1
     Firing Order 1-3-4-2
     Maximum Power - At 6200 RPM 77 kw/103.3 hp
     Maximum Torque - At 3400 RPM 145 N.m 106.9 lb ft
    Cylinder Bore
     Diameter 79 mm 3.1 in
     Out of Round - Maximum 0.0065 mm 0.00025 in
     Taper - Maximum 0.0065 mm 0.00025 in
    Piston
    MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 2 of 330

    Jan 07, 2009 | 2004 Chevrolet Aveo

    Not finding what you are looking for?
    2011 Chevrolet Aveo Logo

    Related Topics:

    307 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6918 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...