Question about Chevrolet Lumina

1 Answer

I have to manually switch back turn signal handle after making a turn

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 443 Answers

Needing new switch under the steering wheel .. its a pretty good job to do .. removal of wheel to get to the plastic switch one of the ears is broken not letting it return when you turn your corner.

Posted on Jun 26, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: Turn signal won't click back

the cancel cam in the multifunction switch is bad...switch needs replaced

Posted on Nov 09, 2008

lancer721
  • 229 Answers

SOURCE: Turn signal won't go back to "Off" by itself.

There is a device in the steering column that switches the turn signal back off. These do go out occasionally and since your vehicle is a 2007 it will probably be covered under warranty.

Posted on Nov 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My turn signals sometimes will quit working then I have to hit the hazard lights button leave it on and then turn my turn signals on then they work what causes this to happen


When the turn signals quit working pull up , down , front to back an back to front on the turn signal switch handle . Do they work when doing this ? Pontiac had bad switch . The power for the turn signals goes through the flasher / hazard module . Could be the switch or the module.
The HAZARD LPS fuse in the left hand instrument panel (LH IP) junction block supplies battery positive voltage to the flasher module, which is part of the hazard switch assembly. The TURN LPS fuse in the LH IP junction block supplies ignition positive voltage to the flasher module. The turn signal lamps may only be activated with the ignition switch in the ON position. When the turn signal switch is placed in either the left or right position, current flow is from the flasher module's output to the turn signal switch assembly. The flasher module then sends an on-off voltage signal to either the left or right turn signals and their instrument panel cluster (IPC) indicator. When the hazard switch is pressed, all the turn signal lamps will flash including both IPC turn signal indicators.

Mar 12, 2016 | 2001 Pontiac Grand Am GT

1 Answer

Why is my turn signal not staying engaged when you click the handle down?


There's a plastic pert on the turn signal switch that has broken or worn down. Replacing it is impossible without special tools to remove the steering wheel. There is a procedure to follow to dis arm the air bag before you try to remove the steering wheel. A Chilton manual will give you instructions.

Aug 21, 2014 | 2006 Chevrolet HHR

1 Answer

Signal handle wont snap back after making a turn


You will basically have to replace the cancel cam to correct this problem. Some disassembly of the steering wheel components may be required and if the vehicle is equipped with air bags it is probably better left to a professional.

Apr 13, 2014 | Chevrolet Lumina Cars & Trucks

1 Answer

2000chevycavalier left turn signal don't blink and makes a buzzing noisr


its in the switch on the column. try pushing forward on the turn signal handle while turning the switch on and hold it there to see if it starts blinking .my 95 grand prix se has the same problem. i have to get a switch from a place call pull appart its a junk yard .

Jan 24, 2013 | 2000 Chevrolet Cavalier

1 Answer

69 firebird turn signal switch does not cancel, need blow up of internal parts in column


You need to replace turn sinal switch its not hard remove center of steering wheel (horn button) remove steering wheel bolt with steering wheel puller pull wheel off remove turn signal handle three screws and emergency button, under dash on right side of steering colume disconect turn signal wires tape a long wire to the end of connector pull turn signal wires out with out pulling tape wire out so you can tape new turn signal wire connector to wire so you can pull it back through

Jun 29, 2011 | Pontiac Firebird Cars & Trucks

1 Answer

How do i remove the turn signal switch from a 1984 nissan 300zx?


What you really want to remove is the "Combination Switch" which controls the
a) headlights b) turn signals, and c) windshield wipers.
The new switch comes with the Left-hand handle attached (expect to pay $$$).

I found your solution (with illustration and replacement parts) at
www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c15280071fa4
Autozone will expect you to register with the site - free. Since your car is a 1984, buy
a Haynes manual - $20 anywhere (try Pep Boys, Advance Auto Parts, etc.)

(I don't work for Autozone) Autozone sells 2 replacement switches:
the one you want is: Duralast SW1836 $122.99 - it has the combination switch and handle only.
They also sell: Duralast SW1690 $170.99, which has the combination switch/handle and also a
collar going around the steering wheel and another switch and handle on the right side of the column.

1. remove steering column cover.
2. unfasten the wiper switch electrical connector.
3. remove the wiper switch-to-combination switch retaining screws, then pull the wiper switch off of the combination switch.
4. The combination switch is now disconnected and can be removed.
5. Installation of new part is reverse of removal.

Oct 13, 2010 | 1984 Nissan 300ZX

2 Answers

Cruise control stopped working on my 93 sierra changed cruise control module under hood still wont work whats wrong?!


it is most likely the button itself being worn. replace the button.(i think it is on the turn signal in your truck) if it is the signal switch kind, you will need the whole multifunction switch.

Dec 18, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

Kia rio turn signal stalk?


Yes that is the handle, that is refered to as the stalk or multifunction switch, it is always on the steering column.

Dec 29, 2008 | 2003 Kia Rio

1 Answer

Turn signal won't go back to "Off" by itself.


There is a device in the steering column that switches the turn signal back off. These do go out occasionally and since your vehicle is a 2007 it will probably be covered under warranty.

Nov 29, 2008 | 2007 Chevrolet Equinox LS New Cars

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...