Question about 1989 Chevrolet K3500

Open Question

1989 1 ton dump truck chevy power steering pump install

I installed new Steering pump but the bolt that goes in the pump is leaking, is there a rubber seal suppose to go in there?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: pwr steering pump failure GM truck

check to see if truck has a power steering pump cooler try to bypass cooler sounds like it has a blockage in the cooler not allowing fuild to circulate should fix problem

Posted on Nov 26, 2008

Ad
stevehinrich
  • 61 Answers

SOURCE: chevy silverado power steering

The power steering pump shaft may have broken inside the pump. I have seen this happen on a these trucks. Have your pump checked.

Posted on Mar 03, 2009

  • 52 Answers

SOURCE: Power steering pump on a 1978 Chevy half ton

First, remove the ps belt by loosing the adjustment bolts, then remove the hoses from behind it, then unbolt the bracket from the engine that the pump sits in. I believe that there are three bolts that do this. One off of the exhaust manifold, one on top and one underneath. Once you have gotten pump off of the motor you need to remove the pulley from the pump. KD tools make a great tool for this, part # KD 2897, about 60 bucks at napa. Follow the directions with the tool to remove the pulley and to replace it on the new one. New pumps don't come with the pulley and can be bought with the resevior. The pulley has to come off to get the pump out of the mounting bracket.

Posted on Aug 09, 2009

  • 1 Answer

SOURCE: Is the power steering pump in a chevy 1/2 ton 5.7

vladkov your an idiot power steering systems run on hydraulic power. The pump is driven by the engine with forces fluid through the gear and assists your steering efforts. I have changed my steering gear twice and my pump. There's nothin electronic about it. Steering assist is electronic and thats a whole diifferent ball game, it only comes on newer vehicles. Changing a p/s pump on a 98 chev is pretty simple, you just need a puller to pull the pulley off so you can get at the mounting bolts. Take those and your 2 lines off (making sure to mark which one goes where) and that's pretty much it.

Posted on Dec 03, 2009

pippall
  • 1486 Answers

SOURCE: my 2006 chevy impala has a massive power steering

You can change the seal.But check the shaft for a tram line type grove.If this is excesive then change the pump

Posted on Dec 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How can I replace the water pump on a 2004 Grand Prix GTP superchargered?


WELL YOU NEED TO DRAIN COOLANT SYSTEM.PLACE A LARGE DRAIN PAN UNDER THE RADIATOR TO CATCH COOLANT WHILE DRAINING RADIATOR.ONCE ALL COOLANT DRAINED OUT.REMOVE DRIVE BELT.REMOVE WATER PUMP PULLEY.REMOVE POWER STEERING PUMP AND MOVE IT ASIDE.THEN REMOVE WATER PUMP.MAKE WATER PUMP MOUNTING SURFACE CLEAN THEN INSTALL NEW WATER PUMP AND GASKET IN PLACE.IF WATER PUMP GASKET IS PAPER TYPE PUT GASKET SEALANT ON BOTH SIDES OF THE GASKET.IF YOU HAVE RUBBER GASKET DONT USE NO GASKET SEALANT.INSTALL NEW WATER PUMP TORQUE LONG BOLTS TO 25 FT LBS AND TORQUE SHORT BOLTS TO 16 FT LBS.TORQUE WATER PUMP PULLEY TO 115 INCH POUNDS.TORQUE POWER STEERING PUMP BOLTS TO 25 FT LBS.THEN INSTALL DRIVE BELT.FILL THE COOLANT SYSTEM.START THE VECHICLE AND CHECK FOR LEAKS.

Mar 25, 2011 | Pontiac Grand Prix Cars & Trucks

2 Answers

I need to find out how to remove the power steering pump on a 2006 pontiac grand prix 3.8L


Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg
*This originally came from abauto

Mar 24, 2011 | 2006 Pontiac Grand Prix

1 Answer

I WILL LIKE TO KNOW HOW CAN I REPLACE THE POWER STEERING PUMP ON A 2001 CHEVY MALIBU


1. Remove serpentine belt

2. loosen power steering pressure and return hoses

3. Remove nut from pressure line mounting on alternator bracket

4. remove power steering pump mounting bolts.

5. Lift pump assembly from engine mounting and remove hoses.

6. Reverse order to install. Fill and bleed system.

NOTE: A new or rebuilt power steering pump will most likely not come with a pulley attached. You will need a power steering pulley remover/installer tool to transfer the pully from the old pump to the new one.

Feb 19, 2011 | Chevrolet Malibu Cars & Trucks

1 Answer

Replacement steps for power steering pump - orginal one leaking thanks


REMOVAL & INSTALLATION 2.4L Engine Fig. 1: Location of the power steering pump - 2.4L engine 87958079.gif
  1. Disconnect the negative battery cable.
  2. Disconnect and cap the power steering fluid lines from the pump.
  3. Remove the mounting bolts, then remove the power steering pump. To install:
  4. Install the power steering pump.
  5. Install the pump mounting bolts and tighten to 22 ft. lbs. (30 Nm).
  6. Uncap and connect the fluid lines to the power steering pump. Tighten the line fittings to 20 ft. lbs. (27 Nm).
  7. Connect the negative battery cable.
  8. Fill the power steering pump with fluid and bleed the air from the system.
  9. Road test the vehicle and verify no leaks.
3.1 Engine Fig. 2: Power steering pump mounting detail - 3.1L engine 86888066.gif
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt.
  3. Unfasten the power steering pump-to-engine bolts.
  4. Pull the pump forward, then disconnect and plug the pressure tubes. NOTE: Place a rag under the pressure tubes to contain any excess power steering fluid.
  5. Remove the engine mount, and remove the pump. NOTE: To remove the engine mount, support the engine with a suitable jack by the oil pan. Make sure to use a thin piece of wood on the jack pad to disperse the weight and prevent oil pan damage. To install:
  6. Position the pump and install the engine mount. Tighten the engine support-to-mount bolts to 96 ft. lbs. (130 Nm). Tighten the engine mount-to-body bolts to 49 ft. lbs. (66 Nm) and the nut to 31 ft. lbs. (42 Nm), and remove the jack from the oil pan.
  7. Unplug and connect the pressure tubes.
  8. Install the serpentine drive belt.
  9. Fill the power steering pump reservoir with the proper type and amount of fluid. Bleed the power steering system.
  10. Connect the negative battery cable and check for leaks.
prev.gif next.gif

Nov 20, 2010 | 1999 Chevrolet Malibu

1 Answer

Cant find were to put powersteering fluid


Power Steering Pump Removal & Installation 3.8L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Place a drain pan under the vehicle.
  3. Remove the accessory drive belt from the power steering pump pulley.
  4. Raise and safely support the vehicle.
  5. Remove the right front tire and wheel assembly.
  6. Remove the hoses from the power steering pump.
  7. Remove the mounting bolts and the power steering pump from the engine.
  8. Remove the reservoir and pulley from the pump if necessary.
To Install:
Power steering pump removal/installation (3.8L engine) gm-08-38-480.gif

  1. If removed, install the power steering pump reservoir and pulley on the power steering pump.
  2. Position the power steering pump to the engine and install the mounting bolts. Tighten the bolts to 25 lb ft (34 Nm).
  3. Install the pressure and return hoses to the pump.
  4. Install the right front tire and wheel assembly.
  5. Lower the vehicle.
  6. Install the accessory drive belt.
  7. Fill and bleed the power steering system.
  8. Inspect the system for leaks.
  9. Remove the drain pan from under the power steering pump area.
3.4L Engine To Remove:
  1. Place a drain pan under the power steering pump.
  2. Remove the coolant reservoir.
  3. Remove the pulley from the power steering pump.
  4. Remove the wiring harness near the power steering pump and place it out of the way.
  5. Disconnect the fluid hoses from the power steering pump.
  6. Remove the mounting bolts from the power steering pump and remove the pump.
To Install:
Power steering pump removal/installation (3.4L engine) 88008g71.gif

  1. Position the power steering pump assembly to the engine and install the mounting bolts. Tighten the mounting bolts to 25 lb ft (34 Nm).
  2. Install the wiring harness in its original position.
  3. Install the pulley on the power steering pump.
  4. Install the coolant reservoir.
  5. Fill and bleed the power steering system.
  6. Inspect the system for leaks.
  7. Remove the drain pan from under the power steering pump.
prev.gif next.gif

Sep 18, 2010 | 2000 Chevrolet Impala

2 Answers

Looking to see haw difficult it is to change power steering pump.? any ideas Iam some what mechanicaly inclined


GM Astro/Safari 1985-1996 Repair Guide
Power Steering Pump - REMOVAL & INSTALLATION
(see Figures 1, 2, 3, 4, 5, 6 and 7)

199f8a3.jpg

Fig. 1: Exploded view of the power steering pump assembly mounting-2.5L engine

1544b7a.jpg

Fig. 2: Exploded view of the power steering pump assembly mounting-early-model 4.3L engine

8c93529.jpg

Fig. 3: Removing the power steering pump pulley-1985-92 vehicles

1995aea.jpg

Fig. 4: Installing the power steering pump pulley

d000dbb.jpg

Fig. 5: Pump pulley removal and installation-1993-96 vehicles

e8e94e6.jpg

Fig. 6: Exploded view of the power steering pump mounting-late-model 4.3L engines (1993-96 shown)

44caf14.jpg

Fig. 7: Typical power steering pump hose routing-1996 shown


The following procedure requires the use of the GM Puller tool No. J-29785-A (1985-92), Puller J-25034-B (1993-96) or equivalent, and the GM Pulley Installer tool No. J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993-96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
WARNING Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  1. Remove the power steering pump from the vehicle.
To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm).
On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  1. Install the pump pulley using the GM Pulley Installer tool No. J-25033-B or equivalent. Press the drive pulley onto the power steering pump.
  2. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  3. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment.
  4. For 1993-96 vehicles install the upper fan shroud and the hood latch assembly.
  5. For 1996 vehicles, install the air cleaner assembly.
  6. Connect the negative battery cable.
  7. Refill the power steering reservoir and bleed the power steering system.
  8. Remove the jackstands and carefully lower the vehicle.
  9. Road test the vehicle, then check and top-off the power steering fluid.

hope this help (remember rated this post) Good luck.

May 13, 2010 | 1989 GMC Safari

1 Answer

Replace power steering pump.


  1. Disconnect the negative battery cable.
  2. If necessary, remove the air cleaner duct and the air cleaner.
  3. Remove the drive belt from the air conditioning compressor, if equipped.
  4. Loosen power steering pump belt adjustment as follows:
    1. Loosen the pivot and mounting bolts.
    2. Loosen the idler pulley locknut and turn the adjusting nut counterclockwise to remove the power steering belt.
  5. Loosen the power steering hoses at the pump and remove the bolts holding the power steering pump to the bracket.
  6. Disconnect and plug the power steering hoses and remove the pump from the vehicle.
To install:
  1. Using new O-rings, connect the power steering hoses to the steering pump.
  2. Install the power steering pump and secure it with its mounting bolts. Tighten the front and rear mounting bolts to specifications.
  3. Install the remaining components in the reverse order from which they were removed.
  4. Connect the negative battery cable.
  5. Fill the power steering system, start the engine and turn the steering wheel from side-to-side to bleed air from system

Feb 14, 2010 | 1997 Nissan Maxima

2 Answers

How to replace power steering pump


2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg

Sep 07, 2009 | 2004 Pontiac Grand Prix

1 Answer

Changing power steering pump


Power steering pump special tools

519a4ae.gif
Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Jun 28, 2009 | 1999 Ford Taurus

2 Answers

How do I repair a leaking power steering hose?


ok thees instructions that i have is for replacing the power steering pump but it has a great pic witch shows the power steering hoses i hope it helps


NOTE The following procedure requires the use of the GM Puller toolNo. J-25034-B or equivalent, and the GM Pulley Installer tool No.J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. Remove the air cleaner assembly for access.
  3. Release tension and remove the drive belt.
  4. Remove the power steering pump pulley using a suitable puller tool.
  5. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  6. Position a fluid catch pan under the power steering pump.
  7. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
    WARNING Be sure to cap all openings in the pump hydraulic system toprevent excessive fluid spillage and the possibility of systemcontamination.
  8. Remove the power steering pump from the vehicle.

    0900c15280227d22.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Pump pulley removal and installation


    0900c15280227d23.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Exploded view of the power steering pump mounting


    0900c15280227d24.jpg enlarge_icon.gifenlarge_tooltip.gifFig. Typical power steering pump hose routing

To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secureusing the retaining bolts. Tighten the nut to 30 ft. lbs. (41 Nm).
  3. Install the pump pulley using the GM Pulley Installer tool No.J-25033-B or equivalent. Press the drive pulley onto the power steeringpump.
  4. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  5. Install the drive belt.
  6. Install the air cleaner assembly.
  7. Connect the negative battery cable.
  8. Refill the power steering reservoir and bleed the power steering system.
  9. Road test the vehicle, then check and top-off the power steering fluid.

Apr 23, 2009 | 2001 GMC Safari

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...