Question about 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Restarting problems 3 times now ive tolk a short drive shut the truck off about 30 min later tried to re start it started for about 3 seconds and died will not restart just turns over checked fuses and stuff nothing then later tryed to start fired right up like nothing hapend only has about 65000 miles runs good it will work fine for weeks its the v8 gas help

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 176 Answers

The first thing you need to check is your coolant level. If it is low then the Coolant Temperature Sensor will not be in coolant, but in air, or steam, but either way it will signal the computer that the engine is cold and therefore deliver a very rich fuel mixture, flooding the engine. It could also be the engine temp sensor itself, sending incorrect temp readings to the computer. Either way once the engine has been allowed to cool down, the false signal to the computer will be correct. If the truck is emitting black smoke once it warms up, then this would be another sign that the Engine temp sensor is bad.

Posted on Jun 11, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 701 Answers

SOURCE: Burning out the pickup coil in 1986 F-150 w/302

Hello genobeano: My name is Roger and I will give some information that should help. When you replace the pick up coil also replace the ignition module. The ignition module will short out the pick up coil. If the module is attached to the side of the distributor be sure to use die electric grease when installing the module on the distributor. Should you not use the grease you will burn up the ignition system. By the same token should the pick up coil short out the module will burn out. The fact it runs for a short time says that you have a heat problem. Normally is in the ignition system. There was a tech bulletin to replace the pick up and module as a unit to correct the problem.
Please rate the answer as this lets us know you received correct information. Should you need further help please just ask. Thank You for using Fix Ya. Roger

Posted on Jun 17, 2009

  • 1 Answer

SOURCE: Wont start unless jumped or restarted within 30 mins

I had the same problem, but it wasnt happening every time. Alt and Battery tested good. About 1 month later the alternator went out and I had to have it rebuilt.

Posted on Dec 16, 2009

  • 1 Answer

SOURCE: 2000 Ford Ranger 4.0L V6 - Engine died while

check all fuses, any ground cables disconnected?

Posted on Feb 21, 2011

ZJLimited
  • 17970 Answers

SOURCE: 2006 f250 diesel....crank and crank

The first thought that comes to mind is a high pressure oil leak. The injectors have a snap ring on top that sometimes becomes detached and it will create these symptoms.

When you depress the brake it sends a signal to the PCM (Powertrain Control Module) and the PCM increases the idle because it predicts you are about to shift into gear. If the truck has a high pressure leak inside the engine it will have a hard time building pressure initially and once the oil warms and thins out the High Pressure Oil Pump cannot hold the pressure and the oil leaks faster because it is thinner.

You may have a leak around the pump area which is under the turbo also. The IPR which is the regulator that controls the oil pressure may also be bad. It is directly under the turbo as well. The IPR is located under the turbo on the High Pressure Oil Pump cover. You stated the seals were leaking on the IPR itself? If the orings are damaged or if the screen in the end of it is collapsed or even punched through with a small hole it will need replaced. Screen damage is usually a sign of debris entering it from either dirt from a previous repair or something is coming apart inside.

Make certain you have clean oil and fuel filters. Yor may want to check fuel pressure as well. It should be somewhere around 55psi on acceleration.

Additionally, I suggest check for voltage at the connector on the fuel pump. The pump is mounted in the filter housing on the frame and the connector is at the front of it. The pink and black wire should have 12 volts with the key on for about 30 seconds. If the pump has voltage but is not running, then your pump has failed. If there is no voltage then check fuse 2.40 in the central junction box. This is the fuse that feeds the inertia switch through the fuel pump relay. I have included a fuse box layout and a wiring diagram (click over images for zoom)...

zjlimited_1990.jpg

zjlimited_1991.jpg

Additionally, will need to scanned the PCM to know if some fault code is stored there.

Keep us updated.

Posted on Oct 08, 2011

  • 3 Answers

SOURCE: 1988 ford ranger 2.9 ltr engine stalls while driving , restarts in a few minutes usually

There are several possibilities, but based on how you described the symptoms I suggest a profile igniton pickup. On these systems the failure usually begins as dropping a cylinder occasionally,like a misfire,mostly during high underhood temperatures,will manifest into stalling and finally into a stall with no resart condition. Symptoms are most likely to occur in summer. The pickup is inside the distributor and the distributor must be disassembled to install it,the trickiest part being the removal and installation of the distributor drive gear. They are iron and easily broken. The simplest solution is another distributor. The ignition modules typically do not fail in this manner,but this is classic for the pickup coil. A code for loss of pip signal should be present, it is possible for a code to not be present,though very unlikely. Having worked on these systems for years this would be my first area of diagnosis.

Posted on Mar 20, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1985 d100 truck has just started to stall out after warming up and driving for 30 to 40 min's and won't restart for 15 to 20 min is that coil breaking down or voltage reg or the square box with all


is it fuel or spark thats what you need to check the older models have problems with relays overheating it is possible you can check the codes with the key on i think its 3 times the ignition on and keep it on the third time without starting and count the times the check engine light flashes it should start 1 long 2 short and if no codes 3 short and 3 short or 1 long 2 short so try it and check all first fuel spark whick one cuts off when wont start

May 11, 2014 | Cars & Trucks

1 Answer

Start and stall


unhook the battery for 30 min

Jan 02, 2014 | Cars & Trucks

1 Answer

Get no current to coil.....


starting problem ,takes 4-5 times turning over engine then blue smoke comes out of exhaust ,is very reliable when got started though -
ive replaced battery/glowplugs-&-relay/
a recovery man says no power to glowplugs ?
can you advise ?

Nov 29, 2012 | 1990 Dodge D150

3 Answers

2000 vw cabrio runs normal and shuts down, takes 5 to 20 minutes to restart, engine cranks but doesnt start, changed ignition coil, pulled diagnostic codes getting short to ground codes on cylinder...


On some models, the Engine Control unit has a power supply relay. These relays some times get internal dry solder points. After driving for some time the the solder will get hot and separate. When it cools down it makes contact again. You will have to replace this relay or open it up and re- solder the solder joints. The relay is usually located on the main relay station in position 3. the relay station is located behind the right dash panel.[right hand drive vehicles]. You may need to refer to a manual for your specific model to find the exact location of the relay.

Jun 04, 2010 | 2000 Volkswagen Cabrio

1 Answer

2000 VW Beetle dies occasionally and won't start for a while


run a scan tool on it and make sure there are no codes, if there is codes address those problems first, if no codes.. next time it won't start check for fuel preasure. it is probably a fuel pump getting ready to go out or they may be a large amount of something other than gas clogging the pick-up sock at bottom of fuel pump.

Mar 07, 2009 | 2001 Volkswagen Beetle

1 Answer

My avenger cuts off after being driven for at least 5-30 minutes


a very common problem with these cars is the crankshaft position sensor. also camshaft position sensor. they will make the car do exactly what you described. let me know what you find

Jan 06, 2009 | 1995 Dodge Avenger

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...