Question about 1992 Ford Crown Victoria

1 Answer

1992 Crown Vic has gas running out of filler tube

Gas is leaking out and when gas cap removed, gas spews out.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 26 Answers

Replace the filter.

Posted on Apr 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jim9813
  • 124 Answers

SOURCE: Replacing fuel filler neck on 2000 Crown Vic

Good news, no the tank doesn't have to come down. However, there needs to be less than 3/4 tank. Jack it up and set on a jack stand, remove the wheel, four screws housing to pipe, filler pipe sensing hose from filler pipe, screw retaining the cap, four retaining screws from filler pipe, screw from filler pipe retainer, slide into the tank until it can be rotated and pulled out through the fender. lube the tank grommet with clean oil and reverse the removal for install.

Posted on Aug 21, 2009

planet-x
  • 232 Answers

SOURCE: 2005 Ford Crown Victoria Trouble filling gas tank.

The tank vent pipe may be blocked or kinked, it usually branches off the main tank filler pipe and can be seen from under the car.

Posted on Oct 23, 2009

  • 1 Answer

SOURCE: raw gasoline vapor 1992 ford Econoline chassis, motorhome

no power to my blower motor no power to wier that plugs into blower motor dont know were the fuse or relay switch is

Posted on Feb 09, 2009

Sean80000
  • 1867 Answers

SOURCE: how big is the gas tank on a 1992 ford crown vic.

1992 Ford Crown Vic 4.6 L V8 Automatic

Fuel tank capacity is 20 gallons (US).

Your fuel consumption will be affected by many factors, such as :
- how you drive the vehicle
- the condition and tune of the motor
- driving conditions (traffic, city use, highway use etc)
- tire pressures
- type and grade of fuel used .

It is impossible for me to estimate what fuel consumption you can expect from your own particular car without a whole lot of information.

It's unwise to run the vehicle for long with no working fuel gauge.

Posted on Dec 17, 2010

  • 8 Answers

SOURCE: My 99 Crown Vic acts like it isn't getting gas

Was the fuel tank drained and flushed when the fuel pump was replaced? By this time it will have collected a lot of junk and gunk. Without cleaning the tank, the fuel pump will simply clog and stop working again.

Posted on Oct 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Gas cap code put new one on check egine light still on


could be your oxygen sensor or catalytic converter.. You may check for leaks in manifold as well.Mass air sensor could also be at fault.

Oct 13, 2014 | 2002 Cadillac Deville

1 Answer

How to remove the fuel filler neck on my 1999 Dodge Grand Caravan 3.8 ltr. engine


OPEN GAS CAP FLAP THEN YOU NEED TO DRAIN GAS BELOW FILLER NECK.THEN LOOSEN REMOVE SCREWS IN THE GAS CAP FLAP AREA WHERE FILLER TUBE CONNECTS THEN GO UNDERNEATH VAN LOOSEN REMOVE HOSE CLAMPS AND REMOVE THE HOSE AT THE FILLER NECK BELOW THE GAS TANK.SPRAY WD40 AROUND HOSE AREA AT METAL FILLER TUBE STICK OUT GAS TANK.CAREFULLY USE LARGE PAIR OF CHANNEL LOCK PLIERS TO REMOVE WORK HOSE OFF METAL TUBE FROM GAS TANK. IF YOU CANT REMOVE HOSE WITH HANDS.BECAREFUL NOT TO MAKE ANY SPARKS.PLACE RAGS AROUND ANY METAL PARTS TO KEEP CHANNEL LOCKS FROM HITTING METAL MAKING SPARKS.

Jun 23, 2011 | 1999 Dodge Grand Caravan

1 Answer

How big is the gas tank on a 1992 ford crown vic. how many miles to the gallon. my gas gauge doesnt work. so i dont know anything about the gas.


1992 Ford Crown Vic 4.6 L V8 Automatic

Fuel tank capacity is 20 gallons (US).

Your fuel consumption will be affected by many factors, such as :
- how you drive the vehicle
- the condition and tune of the motor
- driving conditions (traffic, city use, highway use etc)
- tire pressures
- type and grade of fuel used .

It is impossible for me to estimate what fuel consumption you can expect from your own particular car without a whole lot of information.

It's unwise to run the vehicle for long with no working fuel gauge.

Dec 17, 2010 | 1992 Ford Crown Victoria

1 Answer

2003 crown vic check engine light on and can't fill gas tank to fast or it comes out bottom of car?


Might have a leak in the fuel filler neck. either the neck itself has a hole (rust?) or the short rubber hose that connects the neck to the fuel tank is bad. Normally the fuel system is sealed, if the gas cap is loose, for example, that will cause a check engine light. I think you have a hole somewhere in the tank or filler neck that is causing this.
If you can examine it from underneath, you might be able to see the problem, look for stains from the gas. If you can see the problem, it should not be hard to fix.

Aug 28, 2010 | 2003 Ford Crown Victoria

1 Answer

Can't fill gas tank to fast on 2003 Crown Vic


change the vent tubing to the filler neck. Its clogged up or collasped

Aug 27, 2010 | 2003 Ford Crown Victoria

1 Answer

Have a 97 crown vic and everytime I turn a corner


I would look under your car and look for gas stain's, it's either going to be the filler or vent hose's or the o-ring where the fuel pump goes into the gas tank.

Feb 03, 2010 | 1997 Ford Crown Victoria

1 Answer

Replacing fuel filler neck on 2000 Crown Vic


Good news, no the tank doesn't have to come down. However, there needs to be less than 3/4 tank. Jack it up and set on a jack stand, remove the wheel, four screws housing to pipe, filler pipe sensing hose from filler pipe, screw retaining the cap, four retaining screws from filler pipe, screw from filler pipe retainer, slide into the tank until it can be rotated and pulled out through the fender. lube the tank grommet with clean oil and reverse the removal for install.

Aug 21, 2009 | 1996 Ford Crown Victoria

2 Answers

Gas spewed out my gas tank in my 1991 civic hatchback while running. drove about 100 miles in 80 degree weather and parked idling for about 5 min when i looked over and gas was spewing out tank while gas...


Sounds like your gas cap may not be on right or is faulty ...and is now heat is forcing the fuel out of your gas tank. If removing and reinstalling the gas cap or even replacing it doesnt work, this is just an idea as to what the problem is. This is a very hazardous driving situation. I would NOT let anyone drive this car at the moment. Call a repair shop that has the ability to tow the vehicle. and expect a price tag somehwere in the range of 600-800 dollars to replace a fuel pump plus towing. Leaking fuel at that rate is not to be taken lightly. In anycase,it could be a fault in the fuel vapor canister, fuel lines clogged or damaged or even a faulty gas cap. I just want you to be safe at all costs...and if towing it ensures it...then do it.

Jul 07, 2009 | 1991 Honda Civic

3 Answers

Where is fuelpump on 2003 crown vic police intercepter


Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

May 16, 2009 | 2003 Ford Crown Victoria

2 Answers

We have a problem with a 1992 crown vic. It bogs


run a presher test on your fuel pump.check your fuel filter. have nice day

Apr 02, 2009 | 1992 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...