Question about Cars & Trucks

1 Answer

All lights are on but won't start sensing - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 26 Answers

Need more info, please.

Posted on Apr 14, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Won t start will not turn over no crank do have lights and battery


then I can only suspect the starter has failed .

Oct 24, 2015 | Cars & Trucks

1 Answer

Cabrio won't re-start - heat problem?


Could be crankshaft sensor.

May 09, 2013 | Cars & Trucks

1 Answer

Car won't always start


heater plugs , remember to heat engine or get them replaced

Mar 19, 2013 | 1990 Oldsmobile Eighty Eight

1 Answer

My lights won't turn off


see the diagram attached, and use the logic sense for troubleshooting, please use the VOM for test the parts defective, loose wires, open or break, switch defective, fuse open. bulbs open.
God bless you
7_10_2012_5_25_33_pm.jpg

Jul 10, 2012 | 1994 Honda Accord

1 Answer

Car wont start..after i stuck wet keys in ignition


Give the key-hole a few days to dry out. There are electronics inside the key-hole that sense the key's position and the immobilizer chip within the key. If these short out, or any other circuits with them, the car won't start/run properly.

Jun 19, 2012 | 2006 Chrysler 300

1 Answer

1999 toyota camry won't start battery is good, half tank of gas and starter is good? Sometimes it comes on and works fine, and other times it won't start?


see the diagrams and proceed with common sense.
Reset the ignition timing to the specification manufacterur +gap reset to the s. manufacturer Very Important
God bless you


5_22_2012_9_35_55_am.jpg5_22_2012_9_36_23_am.jpg5_22_2012_9_36_46_am.jpg5_22_2012_9_37_02_am.jpg

May 21, 2012 | 1999 Toyota Camry

1 Answer

99 suzuki vitara stalls out all the time engine lite comes on. Now it won't start. Almost like it is not getting any gas.


The information below was complied by me, it explains what causes the check engine light to come on and the process of finding the cause.
When the Check Engine light (or Service Engine Soon or small picture of an engine) is turned on, the systems computer control unit (called the PCM) has sensed a fault in the electronic controls of the engine and/or the emission system. When this happens you will seldom feel the car engine run any different. There are about 200 possible system faults (the gas cap is just one of them) that turn the Check Engine light on, to know what has developed a problem you must have the system tested

Oct 14, 2011 | 1999 Suzuki Vitara

1 Answer

After doing a head gasket repair 2001 Chrysler Sebring 2.7 v6 won't start. It makes a noise like growling but does not turn over. My mechanic is saying we may need to rebuild bottom half but makes no...


You say that it does not turn over, how would you know there's no compression if it don't turn over, unless you mean if won't start up, lets go with it won't start up, if you have no compression, did you bleed down the lifter's, if you did not, with the lifter pump up will hold the valves open and you will not have compression, will be very hard to start engine, remove lifter and bleed them down, also make sure you replace the oil just in case there's water in the oil pan when heads were removed, if there is water could lock engne, now you would need to overhaul lower engine, hope this was very helpful.

Oct 10, 2011 | 2001 Chrysler Sebring

1 Answer

SL2 ? 2000 starting problem


I had the same problem at one time and what the problem was is a short or an exposed wire connected to the starter which causes the voltage to fluctuate which in turn activates a security feature that stops the flow of fuel to the injectors. The car actually senses the possibility of a spark which could possibly ignite the fuel and be a fire hazard. If you turn the ignition on and off repeatedly after a certain amount of time the car will start and run fine. It is a very intermittent problem.

Jan 02, 2009 | 2000 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...