Question about 2002 Oldsmobile Bravada

Open Question

Oldsmobile bravada diagram

Whats the name of the plastic bracket the headlights and grille bolt to?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Molson02536
  • 3854 Answers

SOURCE: what headlight assemblies interchange with a 2000

1998 to 2005 GMC jimmy headlight assemblies are interchangeable, i believe.

Posted on Nov 17, 2009

Ad
techbuster
  • 5081 Answers

SOURCE: trying to find a diagram to replace headlight

Sorry i donot have diagram for the procedure. But the procedure is given below:

Each of the headlight assemblies are braced through the radiator support with a pair of retainers. The retainers for the right headlight assembly are in front of the battery. The retainers for the left assembly are in front of the washer fluid reservoir. Remove the retainers by pulling up on the retainer. With the retainers removed, the headlamp assembly falls forward. Reinstall the retainers to the square tabs on the headlamp assembly and the rivet on the radiator support

Posted on Jan 13, 2010

csmock132
  • 4669 Answers

SOURCE: smog pump 2000 oldsmobile bravada

I do believe it is a maxi fuse in a little fuse box in the fender right beside the battery.

Posted on Apr 16, 2010

  • 300 Answers

SOURCE: looking for front grille part

The is HEADER PANEL.
!996 - 1999 cost $75 after market.
!992 - 1995 is hard to find a cheap one.
Check first the junk yards.

Posted on Oct 08, 2010

  • 33 Answers

SOURCE: flasher button location in 1996 oldsmobile bravada

Do you mean the Emergency Flasher?

This is located on top of the steering column. Push in to activate. Push again to deactivate.

Some models also have the switch located at the 4 o'clock position of the steering column. Just below the starter key and a bit further back. It is round and black. There is a collar that moves around the button. Push in the center of that button to activate. Pull on the collar to deactivate.

Hope this helps.

Posted on Nov 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove grill


the front grille if I remember correctly is held in by clips and plastic removable rivets. most of the removable rivets are simple. either pull the center up and remove rivet or push center in and remove rivet. there may be 2-4 bolts on the radiator support bracket usually 8-10mm bolts

Jul 18, 2014 | 2003 Chevrolet TrailBlazer

1 Answer

1998 oldsmobile bravada fuse box diagram


On this website you find fuse box diagram and description for Oldsmobile Bravada (1998)

Oldsmobile Bravada 1998 fuse box diagram Auto Genius

Nov 22, 2011 | 1998 Oldsmobile Bravada

1 Answer

Replace low beam drivers side headlight on 1993 olds cutlass supreme convertible


Remove turn signal assembly (uses a torx 15 driver). This will expose the two 10mm bolts on the one side of the headlight assembly. Remove the plastic front grill (uses a torx 15 driver - there are about 6 screws). This will expose the other two 10mm bolts on the headlight assembly. Remove the four 10mm bolts to remove the headlight assembly and this will allow you access to the headlight you need to replace.

Feb 18, 2011 | 1993 Oldsmobile Cutlass Supreme

2 Answers

Trying to find a diagram to replace headlight bulbs on a 2002 Oldsmobile Bravada


Sorry i donot have diagram for the procedure. But the procedure is given below:

Each of the headlight assemblies are braced through the radiator support with a pair of retainers. The retainers for the right headlight assembly are in front of the battery. The retainers for the left assembly are in front of the washer fluid reservoir. Remove the retainers by pulling up on the retainer. With the retainers removed, the headlamp assembly falls forward. Reinstall the retainers to the square tabs on the headlamp assembly and the rivet on the radiator support

Jan 13, 2010 | 2002 Oldsmobile Bravada

2 Answers

How do I remove a headlight bulb on a 2006 Lincoln


remove 2 10mm bolts attaching top of headlight to the radiator support.

remove plastic clip attachinig headlight to top/front of fender.

remove 5 phillips screws on top of grill.

carefully pull out grill enough to remove 1 10mm bolt attaching headlight to radiator support and use slotted screwdriver or prybar to seperate headlight tab from the bracket that goes under the bumper cover.

with a little effort and wiggling pull out headlight assembly.

Nov 07, 2009 | 2006 Lincoln Zephyr

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

1 Answer

Instal diagram for nissan xterra grill gaurd


they jusy bolt to bomper brackets and where bumper bolts to bracket hey vote for me ok

May 26, 2009 | 2008 Nissan Xterra

2 Answers

How to remove grill on 1998 Tahoe. Have to replace headlight assy.


THE TOP SCREWS ARE EASY. THEN THERES THE BOTTOM OF THE GRILL. REMOVE PARKING LIGHTS. THERE ARE 3 PLACES AT THE BOTTOM OF THE GRILL THAT HOLD IT. THERE ARE NO SCREWS OR BOLTS TO REMOVE. JUST 3 PLACES WITH PUSH BRACKETS. LEFT, RIGHT AND CENTER,,A LITTLE TRICKY BUT DONT GIVE UP. LIFT AND PULL THESE TABS/BRACKETS. THE BOTTOM CHROME SHOULD COME OUT A TAB AT A TIME. YOU WILL DO GOOD,,,,RIGHT? YES

Apr 27, 2009 | 2003 Chevrolet Tahoe

1 Answer

How to replace headllight lamp


I know your frustration! I cannot believe the complexity of changing the headlights. Chevy has tried to make this a dealer item only just to change a headlight bulb. I will try to explain the procedure unfortunately I do not have photos. First you will need to remove the wheel well liner (two bolts and two plastic push pins). Pull the wheel well housing back (you will need to turn the wheel/tire to gain access) and using a 7mm socket remove the plastic support piece that holds the bumper in place (two bolts). Pull the corner of the bumper down until you can locate the bottom bracket of the headlight assembly that is held by a 10mm bolt. Remove it. (Oh did I mention this is a two person job!) Next move to the front of the vehicle (hood up) and remove all the 10mm bolts holding the upper part of the grill (I think there are eight of them). Now remove the obvious top two bolts on the headlight assembly! With two people - one to work the headlight assembly and one to push down the bumper and pull out on the grill assemble, slowly and carefully pull the headlight assembly straight forward. You will need to be mindfully of the small tabs on the headlight assembly that like to get caught on bumper/grill. If you are just replacing the bulb, you should be able to move the headlight assemble far enough forward to gain access to the bulbs without totally removing the headlight assembly. What a ***** job! SHAME on GM.

Oct 11, 2008 | 2008 Chevrolet Suburban

Not finding what you are looking for?
2002 Oldsmobile Bravada Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8732 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...