Question about 2006 GMC Envoy

Open Question

Where is the oil pressure sensor on 2006 envoy denali located

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 15 Answers

SOURCE: rear seat fuse box in 7 seater 2006 GMC envoy denali

Rear fuse box is under the seat bottom, rear seat (middle row) on the driver's side. There is a plastic cover over the top of it that snaps into place.

Posted on Jun 20, 2009

Ad
  • 7353 Answers

SOURCE: 2006 Yukon Denali, oil pressure gauge malfunction

Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Posted on Oct 30, 2009

duane_wong
  • 6826 Answers

SOURCE: How do I check and possibly replace the engine oil

Oil Pressure Test Check for proper oil pressure at the sending unit passage with an externally mounted mechanical oil pressure gauge. A tachometer may also be needed, as some specifications may require running the engine at a specific RPM.

  1. While the engine is cold, locate and remove the oil pressure sending unit.
  2. Following the manufacturer's instructions, connect a mechanical oil pressure gauge and, if necessary, a tachometer to the engine.
  3. Start the engine and allow it to idle.
  4. Note and record the oil pressure reading when the engine is cold. The engine may need to run at a specified RPM, if so check the vehicle's specification.
  5. Run the engine until normal operating temperature is reached.
  6. Check the oil pressure reading again with the engine hot and record the value. Turn off the engine.
Compare the hot oil pressure reading to the specification. If the reading is low, check the cold pressure reading against the specification. If the cold pressure is well above the specification, and the hot reading was lower than the specification, the engine may have the wrong viscosity oil. Change the oil, making sure to use the proper grade and quantity, and then repeat the test.
Low oil pressure readings could be attributed to internal component wear, pump related problems, a low oil level, or oil viscosity that is too low. High oil pressure readings could be caused by an overfilled crankcase, too high of an oil viscosity or a faulty pressure relief valve.

Posted on Oct 09, 2010

  • 1 Answer

SOURCE: Where is the oil pressure

just had oil pump installed and still have no pressure

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a pressure oil sensor on a 2006 gmc Sierra Denali


it is located at the back of engine on top middle, behind intake. you have to remove sight cover. you will need a special socket

Jul 25, 2014 | 2006 GMC Sierra Denali

1 Answer

How to replace oil pressure sensor


I never had a problem like that, sorry

Jun 29, 2014 | 2007 GMC Envoy Denali

1 Answer

Oil pressure location


it sound like the oil pressure sending unit is bad Had a 91 chevy do the same thing

Apr 04, 2014 | GMC Envoy Cars & Trucks

1 Answer

Oil leaking loss oil pressure


does the oil light is on? if you do not know how to do, take your car to a mechanic. China OBD2 car diagnostic tools wholesale on CareUCar

Apr 03, 2014 | 2006 GMC Envoy XL Denali

1 Answer

Why is my 2007 envoy denali oil pressure dropping?


check oil level in sump. You may have to remove the sump to check for cracked oil pick up line . Check oil pump pressure regulator . replace oil filter as it may be blocked and dropping the oil straight back to the sump.

Mar 14, 2014 | 2007 GMC Envoy Denali

1 Answer

Using oil looking for possible fix on a 2005 envoy denali


GMC Envoy problems and GMC Envoy repair histories -- car repair descriptions reported ... by car, to see how many repairs each car required and where the car is located. ... 5.3L V8; 2006 291-horsepower 4.2L I6; 2005 275-horsepower 4.2L I6; 2004 ... Advised by OnStar not to drive and have it towed. ----------------------------------------------
galletto 1260

Dec 20, 2012 | 2005 GMC Envoy Denali

1 Answer

How do I check and possibly replace the engine oil pressure sensor in a 2006 GMC Envoy Denali?


Oil Pressure Test Check for proper oil pressure at the sending unit passage with an externally mounted mechanical oil pressure gauge. A tachometer may also be needed, as some specifications may require running the engine at a specific RPM.
  1. While the engine is cold, locate and remove the oil pressure sending unit.
  2. Following the manufacturer's instructions, connect a mechanical oil pressure gauge and, if necessary, a tachometer to the engine.
  3. Start the engine and allow it to idle.
  4. Note and record the oil pressure reading when the engine is cold. The engine may need to run at a specified RPM, if so check the vehicle's specification.
  5. Run the engine until normal operating temperature is reached.
  6. Check the oil pressure reading again with the engine hot and record the value. Turn off the engine.
Compare the hot oil pressure reading to the specification. If the reading is low, check the cold pressure reading against the specification. If the cold pressure is well above the specification, and the hot reading was lower than the specification, the engine may have the wrong viscosity oil. Change the oil, making sure to use the proper grade and quantity, and then repeat the test.
Low oil pressure readings could be attributed to internal component wear, pump related problems, a low oil level, or oil viscosity that is too low. High oil pressure readings could be caused by an overfilled crankcase, too high of an oil viscosity or a faulty pressure relief valve.

Oct 09, 2010 | 2006 GMC Envoy Denali

1 Answer

I use 2 qt oil in 3000 miles in my 2006 envoy is


No it is not normal to lose two quarts,Have you seen any oil spots on the ground where you park your Envoy,
take a look under your Envoy to see if you have a small leak and the air from driving it is blowing the oil back towards transmission.

Dec 19, 2009 | 2006 GMC Envoy Denali

2 Answers

2006 Yukon Denali, oil pressure gauge malfunction


Most likely the oil pressure sensor is bad. Its located in the very rear of engine on top of bell housing area.

Oct 30, 2009 | 2006 GMC Yukon Denali

Not finding what you are looking for?
2006 GMC Envoy Logo

Related Topics:

10 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...