Question about 2007 Suzuki Swift 1.3

1 Answer

Socket size needed remove wheel hub - 2007 Suzuki Swift 1.3

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 3,904 Answers

If metric it is somewhere around 18 mm. If this is standard then it will be somewhere in the 5/8ths size

Posted on Apr 14, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

Rear wheel bearing


if its like the 99 winstar:

safely support the van, remove rear wheel, remove brake drum, remove grease cap. remove caged locknut assembly (38mm socket i think.) then pull the hub assembly from the axel. you may need to cut away the inner race if the bearing falls apart. clean axel, apply alittle anti size compound, then push on the new hub assembly. tighten down the hub nut to specifications (should be on the leaflet in the new bearing package), install dust cap, install drum, install wheel, lower and drive :)

May 25, 2010 | 1998 Ford Windstar

1 Answer

How do i repair left front hub & bearing assembly on a 2000 ford taurus v6 24v dohc


BEST TO GET A HAYNES REPAIR MANUAL IT HAS PHOTOS AND INSTRUCTIONS ON HOW TO REMOVE HUB BEARING ASSEMBLY.YOU WILL NEED A 1/2 SIZE TORQUE WRENCH FOR HUB RETAINING NUT.ITS TORQUE IS 170 - 202 FT LBS.MAKE SURE YOUR TORQUE WRENCH MAXIMUM RANGE IS AT LEAST OVER 200 FT LBS TORQUE.YOU WILL ALSO NEED A AXLE NUT SOCKET.ITS A BLACK SOCKET LIKE IMPACT SOCKET.ITS GRADE 8 STEEL.YOU HAVE TO USE THIS TYPE.A REGULAR SOCKET WILL BREAK.WHEN REMOVING AXLE NUT.ITS ON TIGHT.YOU WILL ALSO NEED A 1/2 BREAK BAR TO BREAK IT A LOOSE.ALSO REMOVE WHEEL COVER.WITH CAR WEIGHT ON WHEEL YOU HAVE TO LOOSEN AXLE NUT A LITTLE.NOT ALL THE WAY UNTIL YOU GET CAR OFF GROUND.WORK SAFE BECAREFUL.

Oct 28, 2009 | 2000 Ford Taurus

3 Answers

Socket size needed to remove wheel hub on a toyota celica


32mm.or 34mm. Go to auto parts store and borrow both to make sure. They are high $$$$

May 19, 2009 | 1990 Toyota Celica

1 Answer

What tools do i need to replace front wheel bearing hub assembly


Floor jack- jack car up and put a jack stand under it. A tire lug to remove tire. A 36 mm socket to unbolt axle shaft sticking through bearing hub. Next a Brass hammer with a block of wood. Next center wood on axle shaft sticking through bearing hub and hit with a 4lb brass or steel hammer with a wood block on shaft. Next you need a 10mm or 12mm socket on back side of bearing hub should have 3 bolts holding it unbolt. Last use a pry bar and gradually pry bearing out and no there not pressed in like a lot of people think.
(Socket sizes maybe different)
If you take it somewhere it would cost about $800 and up.

May 03, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Sebring wheel bearings


Not 100% sure on size, but ask for TORX socket to fit hub bolts on your vehicle, at local autoparts store.

Mar 06, 2009 | Ford E-150 Cars & Trucks

1 Answer

What socket is needed to remove the hub on a 1998 ford escort


thinks its about the same as a tempo somehwere in the line of 18 to 24 mm 22mm ...ithink dont quote me on it though-z

Feb 19, 2009 | 2003 Ford Escort

Not finding what you are looking for?
2007 Suzuki Swift 1.3 Logo

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...