Question about Dodge Ram 50

Open Question

Ram 50 custom l026 G63B timing belt - Ram 50 Dodge Cars & Trucks

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 6674 Answers

SOURCE: need the position for timing chain on a dodge ram

This should help.


Posted on Oct 23, 2010

  • 786 Answers

SOURCE: 1990 dodge ram 50 timing belt diagram

Easyest way to get it is go to local autozone and they will print it out for you at no cost. I do it all the time.........please rate this post and good luck and hope info helps.

Posted on Aug 14, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi, i have a 1983 dodge ram 50, i think my fuel filter is pluggin up, so my question is, where is the filter located at and is there more than on? the engine # is G63B Mitsabishi Model L026....Thank Y

I'm not 100% sure on the exact model of your vehicle, but if you check on the inside of the frame on the side your fuel tank is on it should be there.

Oct 05, 2014 | 1983 Dodge Ram 50 4WD

1 Answer

Where can i get a carboratur for a dodge ram 50 model # l026 engine # g63b

Holley makes carby's for most engines so check with a speed shop/auto spares shop and check out the catalogue for one suitable for your engine.

Dec 08, 2013 | Dodge Ram 50 Cars & Trucks

2 Answers

Good morning, thank you for the help with the comments. My truck was runnin fine till this mornin. I was drivinin up a grade and got a power loss, i had a small load of wood on but have pull this grade...

sounds like you are losing pressure could be the exhaust or the piston rings or the head manifold leaking. if you have the engine pressure tested should tell you witch is the problem rings is mostly the problem on a work hourse engine. .

Oct 15, 2013 | Dodge Ram 50 Cars & Trucks

1 Answer

Hello, I got the silent shaft, timed with the cam, crank and oil pump, thank you for the help with comments. now that it is runnin, it runs rougher then before i replaced the water pump and timing belts...

The only way to tell if you have a ring or valve problem is to do the compression test as it the best place to start . Once you have eliminated the compression from the equation then you can concentrate on why the cylinder is getting more fuel than the others. I would be checking for vacuum leaks for the rough running as an incorrect fuel / air ratio will cause missing. We cannot fix everything but we endeavour to point you in the right direction so that you can fix it.

Oct 06, 2013 | Dodge Ram 50 Cars & Trucks

1 Answer

Need too know the timming marks on where to set them at on a 1988 dodge ram 50 2.0 4 cyl

Here are the timing marks for the timing belt and also the balance shaft, when replacing the timing belt you should also replace the balanceshaft belt heres a diagram for both of them good luck and hope this helps.35de2d2.gif9665995.gif

Aug 13, 2010 | 1988 Dodge Ram 50

1 Answer

I am changing the timing belt on my 1989 Ram-50 and need to know how to line it up. the motor is a 2.0 litre and uses 2 belts. What are the marks and where are they?

here are two diagrams to help you do your timing belt, one to line up the timing belt and the other to line up the balance shaft belt, good luck, hope this is what you needed and hope it helps.da22fd0.gifdc33216.gif

Feb 18, 2010 | 1989 Dodge Ram 50

1 Answer

I need the timing marks to set the crankshaft to top dead center for a timing belt replacement. I just need a diagram to show me where the timing marks are located, where should the camshaft pulley mark be...

1986 Dodge Truck RAM 50 4WD 2.6L 2BL 4cyl

Fig. Timing belt and components-2.0L engine

Fig. Location and correct alignment of timing marks for the timing belt (camshaft)

Fig. Timing marks-2.3L diesel engine

Fig. Timing marks-2.4L engine

More details, (free register). Good luck.

Sep 29, 2009 | 1986 Dodge Ram 50

2 Answers


how do you set the timing belt

Aug 13, 2008 | 1988 Dodge Ram 50

1 Answer

Need Help with an 88 custom/2 wheel drive

You need a timing gun to set your timing belt wright..

Jun 02, 2008 | 1988 Dodge Ram 50

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides