Question about Toyota Pickup

1 Answer

1984 CELICA ECU SWAP

Wondering if swaping the 94 p/u ecu with the 1984 celica ecu is it necc. to change distributer as it runs up to about 2500 t0 3000 rpms and drops off or is this a tps prob. worked great with 94 computer is thier that much difference in settings of tps and afm.

Posted by on

  • Lee Ranton
    Lee Ranton Apr 13, 2014

    must be over experts head.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 52 Answers

Big deal

Posted on Apr 16, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What controls the ground for the injectors on a 1992 toyota celica. I have sent out the computer and they sent it back saying it was ok. I have power to the injectors but no ground on # 1 & 3.


The ground goes into the computer to be internally grounded. Maybe bad wires in your harness somewhere.

#1 is a red wire, goes to ecu pin # 12 of the larger (26 pin) dark gray connector of ecu.

#3 ground wire is a yellow wire, enters ecu on pin 25 of same dark gray connector- Connector D.

Gave you that so you could check continuity of the wires. Hope you have an ohmmeter, a multi-meter. Good luck.

Jun 18, 2015 | 1992 Toyota Celica

1 Answer

How do i replace ECU/ECM on 1996 toyota celica?


if it is just the fuel problem with the ecu, replace the chip in side the ecu from the new one you got as then you dont need to re program it then. the fuel chip and control is inside the ecu. you used to be able to get the chips for them and program the codes onto them. should be clip in type chips. if its soldered type as there are 2 types of ecu boards with same part number. you will need to un solder the chip.

Dec 20, 2013 | Cars & Trucks

1 Answer

I have a 2000 celica and it turns over but will not start


On older Celicas (maybe on yours too) there is a 15 amp EFI fuse in the fuse box by the battery. Check for that. If it's out, the fuel pump and the ECU will not come on.

Nov 22, 2011 | 2000 Toyota Celica

1 Answer

Honda jerks


My 94 celica had the same problem, thought it was the tranny turned out to be the ECU, replaced it,never had the problem again.

Sep 06, 2009 | 1991 Honda Accord

2 Answers

2000 Celica electrical problems


check all fuses with test light in cab and under bonnet.

Jun 14, 2009 | 2001 Toyota Celica

1 Answer

What do the diagnostic trouble codes for 85 toyota celica. they are 11, and 6


11 is switch signal air conditioning on during diagnosis check. code 6 rpm signal no signal to ecu.

Apr 22, 2009 | 1985 Toyota Celica

1 Answer

5sfe motor swap to a st184 celica motor in a 94 camry


in the celica motor they run a smaller knock sensor, get a reducing nut from a bolt shop and it will fit, ive done one of these conversions before

Dec 26, 2008 | 1994 Toyota Camry

2 Answers

Electrical diagram


Hi,

Might this help?
They were originally posted here and here.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 16, 2008 | 1992 Toyota Celica

1 Answer

Gearbox conversion.


computer controlled trans so yes ecu has to be changed use pedal assy from auto car and shifter assy if on column change collumn if floor just shifter needs changed probably need fuse boxfromauto car underhood fuse box for prndl to work properly for shifting purposes fuses relays etc.

Aug 11, 2008 | 1992 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...