Question about 1995 Jeep Grand Cherokee

1 Answer

Wife got out of the 1995 Grand cherokee ltd. somehow got into programming sequence apparently by pushing drivers lock manually and turning key back on. Now I have to get in and close the door to operate the power door locks. It used to be I could run these with the door open to lock it after getting out. I have a Haynes manual but it has nothing about the programming sequence. I know these can be complex from my 97 Olds. I have not found anywhere that posts the programming procedure for the door locks etc. No owners manual.

Posted by on

  • 3 more comments 
  • kulkan Jun 18, 2009

    I tried that, and tried the "lock everything and unlock the tailgate with the key". No joy. Appreciate your availability but if it's not the kind of thing that is posted. (security programming for the 1995 GC) then I might as well spend $20 on a used owners manual.

    It starts and runs fine, but no stereo (just flashes) and the big indicator display panel just flashes. Interestingly, if the interior light dimmer switch is pushed all the way to the right, the radio & big lcd panel go black, but. .fan doesn't work. I have a friend with a 97 so maybe he has a manual.

  • kulkan Jun 25, 2009

    This is fixed. It was a 20 Amp fuse. I think it was number 8, but I do not yet have a manual that tells me which fuse does what.

    What it caused was this:

    power Door locks don't work until you close the door and turn on the key.

    Stereo and big display panel flash about twice/second. resetting security didn't change anything. replaced fuse and it was all better.



  • kulkan Jun 26, 2009

    I agree. I expect something to "not work" when a fuse blows. When the owners manual arrives that I ordered I will find out what that fuse was for and post it here.

    It could never have been a broken wire as it was absolutely consistent and a broken wire wouldn't be. If I held in the button in the door frame up by the door hinges then the power locks would work with the door open.

  • Richard Scordino May 11, 2010

    Odd problem, but jeep does strange electrical things (in the design). Only question remaining would be why did the fuse blow?

  • Richard Scordino May 11, 2010

    On some all you need to do is lock and unlock the drivers door using the key.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

There is no programing for the locks to work only with the door closed. Look at the harness between the "A" pillar and the drivers door, you might have a wire broken. With the door open it may strecth the wire and loose contact and when you close the door the broken wire may make contact with the other half.

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I program this remote start . I just got this for a replacment one and It never came with the instuctions Please help me?


Instructions
    • 1 Climb into your Jeep Grand Cherokee with your keyless remote(s) in hand and your manual ignition key. Do not close the driver's door.
    • 2 Hit the "Lock" switch on your driver's side door and insert the key into the ignition.
    • 3 Turn the key to the "Run" position and aim the keyless remote at the steering wheel. Press and hold the "Lock" button for five seconds.
    • 4 Wait for the locks to respond by cycling then program each successive remote (up to four total) by holding the lock until the locks respond. Each remote must be programmed within 20 seconds of the last.
    • 5 Turn the key in the ignition back to the "Off" position then quickly back to the "Run" position within 20 seconds of programming your last remote.
    • 6 Turn the car off and remove the key from the ignition to complete the programming sequence.

hope this helps

Jan 19, 2015 | 2000 Jeep Grand Cherokee Limited

2 Answers

My 1995 Jeep Grand Cherokee Laredo wont start and has blue security light flashing


Did u try unlocking the passenger door with the key?these are very common for the drivers switch goin bad

Apr 19, 2013 | 1995 Jeep Grand Cherokee

2 Answers

Keyless remote 1996 jeep grand cherokee laredo programing


Instructions
  1. Programming the First Transmitter
    • 1

      Unlock all of the Jeepicon1.png Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.

    • 2

      Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.

    • Sponsored Links

    • 3

      Point the remote at the receiver (located by the little bulb on the caricon1.png ceiling) and hold down the "Lock" button for up to 5 seconds.

    • 4

      When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.

    • 5

      Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Feb 11, 2013 | 1996 Jeep Grand Cherokee

2 Answers

Programin the remote control


Open the drivers door, manually lock the door, push and hold the unlock button on your remote. After a couple seconds the lock system should respond with a lock and unlock sequence.

Jul 25, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Windows wont roll down


I suspecft this is a security programming situation. I have something similar going on with my '95. I have to get an owners manual to find the sequences. I stumbled into this by manually locking the front door and turning on the key with the door open.
re: the dash lights. I find if I have the interior light dimmer all the way to the right it locks out some things but moving it back to the middle puts it back in operational mode. aside from the flashing, non playing stero. At least I can drive it and powerlock the doors IF the doors are closed.

Jun 17, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Locks on 2004 Legacy Outback


Not far fetched. The frequencies may bleed like a radio channel does when its not right on. Your two frequencies may be so close or one much stronger(other car) You should have it check before someone else notices it. Good luck

May 25, 2009 | 2005 Subaru Forester

1 Answer

Turns itself off within 2 seconds of being started


Lock all doors and open with key in passenger side door.Then start it..That should reset the security system>>>Hope this helps you and have a great day...

Apr 05, 2009 | 1995 Jeep Grand Cherokee

2 Answers

1999 jeep grand cherokee laredo keyless remote transmitter programing


Open the drivers door and turn the key to the on position. Lock the doors with the switch on the door. After the doors lock point the transmitter to the little bulb on the ceiling. Press the LOCK button and hold it until the doors unlock.

Maybe this info can be help you...
http://autorepair.about.com/library/faqs/bl868f.htm

Jan 20, 2009 | 1995 Jeep Grand Cherokee

4 Answers

1995 Jeep Grand Cherokee Laredo Alarm system


There are switches on the door lock cylinders that are supposed to shut the alarm off when you use the key,but they go bad allot. you could try unlocking the passenger door first, since that one usually gets less use and is less likely to go bad. Otherwise you can disconnect the alarm module, it is located behind the glove box.

May 14, 2008 | 1995 Jeep Grand Cherokee

5 Answers

Alarm shutoff


go to the hatchback and turn the key to the right

May 14, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...