Question about 1995 Nissan Pickup

1 Answer

Front wheel hub gets hot after driving - 1995 Nissan Pickup

Posted by on

  • mike puetz
    mike puetz Apr 15, 2014

    Just finished replacing both half shafts. Degreased hub/bearings and regreased. Did not have a custom nissan socket to set the torque on the axel nut!! But did tighten it back it off and then tightened to 20 deg as the book says. Do I need to back off that axel nut?? Bearings and hub were in perfect working order/ greased at 60,000 by Nissan and now have 80,000 on it. Never off road it. Thank you. 0

  • Johnathan Lence
    Johnathan Lence Apr 16, 2014

    yes you might want to recheck that

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Nissan Master
  • 442 Answers

Need to take wheel off and check to see if brakes are locking up after applying them if not hub bearing needs replaced

Posted on Apr 15, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can you get free wheeling hubs for a 2003 rav 4 all wheel drive


Not without changing most of the front components out.

Jan 12, 2017 | Cars & Trucks

1 Answer

Front wheel hub gets hot atfter driving 20 miles


Hubs will be temperate depending on braking. If there is a failure with a wheel bearing or a brake shoe you will experience grinding noises, which is friction and will cause things to get abnormally hot.

Apr 13, 2014 | 1995 Nissan Pickup

2 Answers

When you replace 2001 kia sportage vacuum hubs with manual, it it just the front hubs that get replaced?


If it is a rear wheel drive predominately then yes you replace the front vac hubs only as the rear is constantly driving, is it a east west motor or north south , that will tell you a lot

Jan 04, 2014 | 2001 Kia Sportage

2 Answers

Warn hubs, installation


Warn Hubs Installation
A truck or SUV with a four-wheel drive suspension uses locking hubs on the front wheels to engage or disengage the front axle shafts from the hubs. This way, you can drive the truck normally with just rear-wheel drive, or engage four-wheel drive mode when you want to drive off-road. These hubs can wear out, and one improvement is to install a set of Warn hubs. Installing a set of Warn hubs takes about an hour.
1.Park the truck and put on the parking brake. Lift the front of the truck with the jack and put the jack stands under the front axle. Take off the front wheels with the tire iron and put them to the side.
2.Disengage the locking hubs using your hands by turning the knob on the hubs. Remove the snap rings holding the hub locks in place with the snap-ring pliers. Pull the hub off the axle.
3.Install the lock ring wheel from the Warn hub kit in the axle with the factory snap ring and the snap-ring pliers.
4.Make sure the Warn locking cap dial is turned to the "Free' position. Install the locking cap onto the lock ring wheel and hub body with a hex-head key. Reinstall the front wheels with the tire iron and lower the vehicle off the jack stands with the jack.
Thank you for using FixYa. Hope this will help your problem and don't forget to rate me.thanks,
Reymond

Oct 18, 2011 | Cars & Trucks

2 Answers

The driver side front wheel does not engage in 4 wheel drive


manual or auto hubs?how do u now it is not engaging?.u can lift the front end up in 4 wheel make sure hubs r engaged .rotate the tire by hand ,and check to see if the drive shaft is turning [from the wheel to the front diff] u most likely have a bad locking hub.if it is not turning ur front tire is not locked up

Dec 29, 2010 | 1994 Ford Bronco

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

Front drive shaft not fully engaged in 4WD, with truck on stands all 4 wheels do rotate but if i stop front wheels the front drive shaft is not engaged


Hi,
Do you have auto locking hubs on the front wheels, or manual locking hubs?
If you have auto locking hubs chances are they are not engaging properly and will need to be removed and spline sets checked for broken teeth on locking hub and locking shaft.
If you have manual locking hubs then check that they are firm when turning to engage them in the lock position.If they are light when engaging them to the lock position then they my have broken/worn out the locking hub and spline. Also check that the engaging spring inside the hub has enough tension to engage the hubs they may be broken. If the hub are all ok then you have a problem in the transfer box, where the 4WD lever is not meshing the transfer box properly. Hope this helps, let me know how you get on.

Jason

Apr 04, 2010 | 2002 GMC Sierra C/K1500

2 Answers

Is it right for your front drive shaft to turn by hand when in park


i'm assuming you have a 4 wheel drive. If that is the case then yes cause when your in two wheel drive mode the front is in neutral

Oct 16, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

I have a Disco II and the wheel hub bearing went and i'm tryign to change it but i cant seem to get the hub off, can any one help with a step to step guide or something, thanks.


RAVE says the following:
1) Release ABS Sensor harness grommet from inner wing valance and disconnect multi plug.
2) Raise front of vehicle.
3) Remove road wheel.
4) Pull ABS Sensor harness through aperture into wheel arch.
5) Release harness from brackets on inner wing valance, suspension turret and front hub.
6) Release stake from drive shaft nut
7) Remove drive shaft nut with assistance & discard.
8) Remove front brake disk (Remove calliper, pad holder, screw and tap to remove)
9) Remove 4 bolts securing wheel hub to steering knuckle.
10) Release wheel hub from steering knuckle then remove wheel hub and drive shaft assembly from axle. DO NOT REMOVE ABS SENSOR FROM HUB. HUB AND SENSOR ARE SUPPLIED AS AN ASSEMBLY.
11) Position the wheel hub and drive shaft on a press, place supports beneath the wheel studs and press the drive shaft from the wheel hub.
12) Remove drive shaft oil seal from axle casing.

Refit is mostly the reverse, you need to take care to lubricate things in the right places and put loctite on the drive shaft and locate the loom and torque everything right.

Mar 24, 2009 | 1999 Land Rover Discovery

Not finding what you are looking for?
1995 Nissan Pickup Logo

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...