Question about 1994 Jeep Wrangler

1 Answer

Installing clutch pedal holden jackeroo 1992 - 1994 Jeep Wrangler

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

A jeep jackeroo? huh.
was your jeep , hijacked?

Posted on Apr 13, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Further to my question regarding where do you find the computer , Keyreader and security isolater in a Holden Jackeroo 2002 with 3.2lt Isuzu diesel motor?


no symptoms stated. (older post)
what computer, name it, PCM. TCM , BCM? what?
what key reader. the ignition key?
will the key has an antenna (round loop) and is on the ignition key switch assembly on moset carts
we dont have JACKeroo's in uSA so...... no books. no examples.

Nov 30, 2015 | Isuzu Cars & Trucks

1 Answer

Where is the temperature sensor on a 92 holden jackeroo


Mate, most of the time these things are located close to the thermostat. You will see wire connector on it. It was has a threaded connection with the engine. Unplug the connector first, and then put a deep socket or spanner on it. Go Pies!

Apr 17, 2015 | Holden Cars & Trucks

2 Answers

Hi guys, searched google with no results so Can anyone tell me if I can adjust the clutch on a Holden jackaroo 3.2 litre petrol manual 1993 please? Thanks


Hi there
No there isent any adjustment on the clutch as its automatic done but you might try bleeding as you might have air in the system which will also give you a 1/2 pedal , if no good you might find that your clutch needs replacing.

Apr 04, 2015 | Holden Cars & Trucks

1 Answer

Holden astra problems


check the fluid level in the reservoir. If full the bleed the air out of the clutch system

Dec 14, 2013 | 2004 Holden Astra

1 Answer

How to blead clutch in 2004 holden clubsport


im assuming its a vy clubsport?
Make sure you remove all the old fluid from clutch resevior and clean it out properly.
You will need to raise the vehicle on a hoist or atleast 4 cat stands .
you will need 3 people in total to get the job done correctly.
fill the clutch resevior with new fluid.
get someone to stay under the car to open slave cylinder to release air.
someone to seat to drivers seat to pump clutch pedal.
and someone at resevior all the time to top up fluid.
when bleeding system just pump the pledal slowly when the person bleeding slave cylinder says hold.hold the pedal down with light pressure when the slave is open you will get air and then little fluid .
repeat process until just good flow of fluid comes out ,once this happens you should have a good pedal..
hope this helps you

May 29, 2012 | Holden Commodore Cars & Trucks

1 Answer

How do you install a clutch master cylinder on a k1500 v6 chevy


Remove the fluid line, then go inside cab at clutch pedal remove linkage that connects master and clutch pedal. Remove bolts that hold it in place and remove unit. reinstall in reverse order and bleed system at clutch slave by opening bleeder then pushing clutch pedal down and holding until bleeder is closed. repeat until solid fluid comes out, then with bleeder closed pump clutch pedal three times and open bleeder to relieve any left over air.

Jun 22, 2010 | 1992 Chevrolet K1500

1 Answer

I have a 1992 nissan 300zx and i just installed a new clutch master cylinder and a new clutch slave. i'm tring to get the pedal to get firm so i can bleed it and get a full pedal,but when the pedal gets a...


you need to bleed the cluch slave cylinder located on the transmission and the clutch operating cylinder located in the passenger front hood compartment next to the power steering resivoir

Mar 30, 2010 | 1992 Nissan 300ZX

Not finding what you are looking for?
1994 Jeep Wrangler Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...