Question about Dodge Stratus

1 Answer

Im replacing a tail light circuit board on both rear lights, is their any special way to do this

1st right tail light, blinker and brakes light went out had a friend help with it, then taking bulb out of left, put it back in and left side doesn't work. So no brake light signal's work. purchased circuit assembly going to put it on today. Don't know what else to do, fuse's are fine and new bulbs.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 52 Answers

Just check accurately bulbs if you mixed it could happen like that, some cars for the brake lights use two contact bulbs some of them single contact, two contact bulbs can give two signals which one is used for brake ligths and another for taillight, so check the bulbs carefully

Posted on Apr 16, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1779 Answers

SOURCE: 1992 Honda Accord LX Brake Light Switch Repair

Of course you can make this repair! I'm wondering about the faulty bulb that shorted out all the brake lights...not sure if that's what happened. Your brake light switch is located on the brake pedal, up above where your foot goes. It has a plug in connector which you unplug, then loosen the locknut where it attaches to the pedal.Put in the new switch, lock nut 1st, then plug it in. Note that the locknut is the adjustment point that determines when your brake lights go on. Adjust the locknut so that the brake lights go on when the pedal is depressed within 1/2 an inch (13mm)of pushing down on it. If the switch is adjusted without enough play (say 1/8 inch or less), brake lights may flicker on and off when you go over a bump.If over 1/2 inch, brake lights might go on only if great force on pedal is used (or not at all, yikes!).For good diagrams of parts check out South Bay Honda (hondapartscheap)web site. You enter the year, model, engine, and you can scroll thru tons of parts. If you have any more questions, do not hesitate to post it for me. countrycurt0

Posted on Aug 08, 2008

  • 88 Answers

SOURCE: rear brake lights don't work

you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

Posted on May 23, 2009

kidspeedy
  • 321 Answers

SOURCE: left rear turn signal light on my 1999 chev. s10 is not working

any increase in bink speed is direcly related to a bulb being burt out.

Posted on Jun 12, 2009

  • 2 Answers

SOURCE: Brake light, Turn signal not working rear right 06' Focus

I have a 2000 ford focus no brake lights. with the brake lights the transmission would not go into drive .replaced the brake light switch checked fuse replaced turn signal switch with no results then i moved onto the wiper switch and replaced it as much to my supp rise it fixed the problems

Posted on Aug 06, 2009

  • 100 Answers

SOURCE: 1997 GMC Sierra p/u. Brake light & blinker out. Lamp & fuse ok.

you probably got the wrong bulb
those are usualy a different number higher wattage, they look exactly like an 1127 but are a 2027 or even a 3027 check the bulb base it has the number printed on it

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 DODGE DURANGO RT REAR TAIL LIGHT OUT AND FRONT LEFT HEADLIGHT GOES OUT BUT TAP HEADLIGHT AND IT COMES BACK ON


Check the harness connection for trailer hitch lights near back bumper in chassis rail. launching a boat gets this connector corroded.

May 17, 2017 | Dodge Durango Cars & Trucks

1 Answer

On my 2003 model 2500HD Silverado, the right tail light doesn't illuminate, although the brake light actuates normally. I have the right blinker function and the back up light also works. I had power...


In those years of chevy trucks they have circuit board in the tail light assembly. You will need to replace the circuit board ( the thing the bulbs push into) you can perchase one at your local auto parts store.

Jul 08, 2011 | Chevrolet 2500 Cars & Trucks

2 Answers

I have a 94 Chevy C1500 and the right side brake light and blinker are not working. The tail light and reverse light work though, and the right front blinker works but it blinks twice as fast as it...


It could be a bad multifunction (turn signal) switch. The way that switch works, it is possible that it can turn on the front blinker and not the rear one. It also cancels the brake circuit so the turn signal can work with the brake pedal depressed.

However, a more likely cause would be a break in the YELLOW/BROWN wire at the rear of the truck. It is common for the connector to get corroded at the left rear frame area where the bed harness connects to the vehicle harness. If you have trailer connections spliced into the wiring harness, these connections are also prime candidates for corrosion. I would look there first. Inspect these harnesses thoroughly all the way up and into the tail light assembly.

If the wires under the back of the truck look good, then I would check for power coming out of the turn signal switch. The wire at the turn signal switch is plain YELLOW (with no brown tracer). It is Pin (M) on the turn signal switch connector. The front signal is a LIGHT BLUE wire at the turn signal switch Pin (H). If you probe these with a test lamp, they should both work the same except the yellow wire will be hot with the brake pedal depressed and the switch NOT in the left turn position. If there is no power at the switch connector, replace the switch.

May 13, 2011 | 1994 Chevrolet K1500

1 Answer

Passenger tail light was staying on then going off intermitinly. now my blinker idicator lights on the dash don't work nor do I have any interior lights what so ever. My blinkers work outside but I have...


I had the same issues and when i removed the tail lights and looked closer their ws moister in the connections where the bulbs went causing corrosion and when i cleaned everything real good renintalled them and havent had any issues since

Jan 31, 2011 | 2005 Dodge Ram 3500

3 Answers

My rear brake light is not working, nor is my blinker at the back right. When I put the right turn signal on it blinks really fast, faster than normal, and the front blinker works. I have replaced both...


Normally with the blinker blinking really fast, it's telling you that one of the bulb is blown, front or rear signals. Check your fuse, and fuse relay to see if it would fix the promblem

Jan 23, 2011 | Chevrolet K3500 Cars & Trucks

1 Answer

Tail lights


These are famous for the circuit boards in the tail lights going bad. If the tail lights are in bad condition, replace the whole tail light, if the lenses are good, then you can buy just the circuit boards. Any (Good) parts store should have them.

Feb 12, 2010 | 1989 Chevrolet C/K 3500

1 Answer

Right tail light went out.


I have had the same issue recently. I have a 2002 Gr Cherokee Ltd 4.7L. At first I thought it was the bulb, replaced the bulb to no avail. Then I thought maybe the bulb was rattled loose due to my subwoofer, but that still was not the case. After testing all my fuses I decided to test all of my lights. The hazards worked, back up lights came on, tail and brake lights were all working also but for some reason the blinkers will go out and the right rear brake light will not come on. It always comes back on for me though, so now I just use hand signals when it is temporarily not working. My only suggestion is a problem in the wiring.

Oct 13, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...