Question about Cars & Trucks

1 Answer

Pinging sound from rear of engine around Bell housing

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

Not enough info, but sounds like your flywheel may be cracked
What make vehicle?

Posted on Apr 13, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

frenchy1954
  • 115 Answers

SOURCE: I Have a 2002 chevy

sounds like the rear main seal remove transmission or engine is the only way to fix this

Posted on Dec 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft sensor located 01 Honda Odyssey 3.5


Hi
Not many places for these to hide.
Either mounted somewhere around the crankshaft pulley area or on the bell housing/ rear of engine block so they can read from the flywheel.
Cheers
Roger

Apr 24, 2017 | Honda Cars & Trucks

2 Answers

Were is engine number on mercedes 3.2 engine


you should be able to read the engine number off the the bell housing. you may have to search around the bell housing to actually see it. typically it can be read off from above.

Aug 06, 2014 | 2001 Mercedes-Benz C-Class

3 Answers

Where is the crank shaft position sensor on a 2002 Jeep crank shaft position sensor


in the transmission bell housing, passenger side at about 11o'clock if looking from the front.

Feb 27, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Where is starter located on 1998 saturn sl1


Starter is located underneath the intake manifold on the back side of the engine. It is bolted into the bell housing of the transmission so that the gear on the starter meshes with the ring gear. Tough to get to, especially if you do not have a lift.

Everyone can find the battery. With the hood up and standing in front of the car look down and to the left of the battery. That big bell on its side shaped metal thing is the bell housing. Follow it around to the rear of the engine.

Jul 06, 2010 | 1997 Saturn SL

2 Answers

I cant get to the top bell housing bolts on my 96 chevy blazer


One way is to remove the back transmission /engine mount. Take the weight of the transmission on a car jack and lower it a few inches, Make sure that no pipes snag or the back the engine catches on the bulk head etc. A couple of wrench extension arms fitted end to end and a universal joint behind the socket should reach those difficult bolts from underneath the vehicle by accessing up between the chassis and the bell housing from the rear. Keep that transmission supported at all times as the full weight of the engine etc is pivoting around the front engine mounts! As an added bit of safety insert one of the lower bolts back into to bell housing and only very lightly tighten it. This should allow the top bolts to be taken out without risking sudden separation of the tranny from block at the bottom putting strain on the upper bolt shafts . When the top bolts are out support the rear of the engine on wooden blocks or some such and only then go to move the 'safety' bottom bolt prior to separation

Apr 17, 2010 | 1997 Chevrolet Blazer

1 Answer

Steps required to remove the standard transmission from a 1992 Toyota pickup. Bell housing bolts, starter, and rear trans. support have been removed, but the trans/bell housing will not separate from from...


Make sure you have removed all the bolts ....you will have to pry hard to remove it out .....be careful not to crack the bell housing ..Pry around the bell housing .good luck

Jan 02, 2010 | 1992 Toyota Pickup

1 Answer

I have a minor engine oil leak. What is the proceedure to R&R valve cover gasket?


check rear end of engine around the gearbox bell housing in case its rear end oil seal

Jun 08, 2009 | 1995 Toyota Celica

1 Answer

Antifreeze leak in back of engine


Sounds like your right rear freeze plugs are probably leaking .. but first you need to make sure its not coming from up around the rear of the intake before pulling the transmission . this would be the best way to fix this problem .. thanks jerry holler if you need more.

Jan 30, 2009 | 1987 Dodge Pickup 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...